Good info. You should just make a centering tool and a z plate in one though. if you ad an angle to the bottom of the plate you can but it against the corner of the work piece and get the center from the top once you square the bottom up.
very interesting I wonder if the ring on the plate is not x,y exactly with the table of the mill than probe might not et the longest diameter inside ring as cross section and eventually not give me factual center.
Another words if my piece of material is not accurately aligned with the table than plexi-glass bracket holding ring I will not get cross reference reflecting center ?
I have a CNC motor controller 3 axis Toshiba TB6560AHQ and 3 BS57HB56-03 Stepper Motors but when I power up the systems after while my motors “gets hot” without using them (in non operational mode) is that any normal?
Do you know if Mach3 v R1.83 can work with USB to Parallel port converting pluck? Because I have a laptop with no Parallel port so I bought a USB to Parallel port converting plucks “any suggestions welcome”
Hello intresting video, but did you make a macro for you self the center the drill.
The rezone that I ask you is that I have to make also something like that for to center my wire for my edm wire machine, and the marco that I have fond on the mach site don't work.
cool stuff, i'm trying to get my screen altered with screen4 like yours but i suck in script writing, did you share your cool screen and script on the yahoo forum ?
Very nice, how are these made and hooked to the control board to make it work. I'm new to cnc and I am using mach3 and the soung logic pc-2- route board rev 1.9
Thanks, homemade tools are great...
sullytrny 1 month ago
Wow why your Mach3 screen is blue? How do I change mine?
AgasVag1 2 months ago
how do you get point cloud data? I would like to touch probe scan a model and import into CAD for refinement and then cnc build.
WHere do I start? Thank you.
jgore27 7 months ago
Where do those soldered leads hook up to? Just a ground?
voltairegoethe 8 months ago
Good info. You should just make a centering tool and a z plate in one though. if you ad an angle to the bottom of the plate you can but it against the corner of the work piece and get the center from the top once you square the bottom up.
musicmaneman1 11 months ago
Good info. You should just make a centering tool and a z plate in one though.
musicmaneman1 11 months ago
very interesting I wonder if the ring on the plate is not x,y exactly with the table of the mill than probe might not et the longest diameter inside ring as cross section and eventually not give me factual center.
Another words if my piece of material is not accurately aligned with the table than plexi-glass bracket holding ring I will not get cross reference reflecting center ?
stivep1 1 year ago
You can get the license at motiontek.ca for 159.
jblakes34 1 year ago
This has been flagged as spam show
I have a CNC motor controller 3 axis Toshiba TB6560AHQ and 3 BS57HB56-03 Stepper Motors but when I power up the systems after while my motors “gets hot” without using them (in non operational mode) is that any normal?
Do you know if Mach3 v R1.83 can work with USB to Parallel port converting pluck? Because I have a laptop with no Parallel port so I bought a USB to Parallel port converting plucks “any suggestions welcome”
Thanks
supperstorm 1 year ago
How much do you pay for your Mach3 license? You can tell me by personal message if you prefer. =)
molinobeer 1 year ago
Cheezy
fjpete 2 years ago
Thanks so much!
rickgaston 2 years ago
too bad the plug in is busted.. we cant make point clouds right now, but is very good for touching off.
terrablader 2 years ago
Hello intresting video, but did you make a macro for you self the center the drill.
The rezone that I ask you is that I have to make also something like that for to center my wire for my edm wire machine, and the marco that I have fond on the mach site don't work.
Greetings Benny
plasmaboog 2 years ago
Could you please post the vb marco for center probe
oakphisto 3 years ago
Could you not put a pin in the middle with a tight fitting spring around it ,insolate from each other and make one pos and one neg for 3D probing
Spydwar 3 years ago
Thankyou, A great job and demo. I will be building it today..
theislandpartyboat 3 years ago
I love it. The edgefinder especially. Super cool.
zackwootensc 3 years ago
Good work .. keep it
rboghdady 3 years ago
cool stuff, i'm trying to get my screen altered with screen4 like yours but i suck in script writing, did you share your cool screen and script on the yahoo forum ?
nappocnc 3 years ago
Nice stuff- thanks for sharing
mnorth1 3 years ago
Very nice, how are these made and hooked to the control board to make it work. I'm new to cnc and I am using mach3 and the soung logic pc-2- route board rev 1.9
jmrks1 3 years ago
That's great Ernie. Thanks for putting all this together as it will be so useful for a later date when I rebuild my router.
baccus61 3 years ago
VERY COOOL!
kmcwhq 3 years ago