How to connect the pins of a flyback Transformer using a 9V and resistor to create 3000V?I want to know how the pins must be connected of a flyback transformer. I have the wires, 200Ohm and 20 Ohm resistors, switch and transformer. I have everything but I wanna know how to connect it.
You ought to build a better enclosure. Current can flow through air without any visible arc. This can be observed by holding your output conductors far enough away that an arc can't be created, and you will hear a hissing noise. These are ion currents, and they CAN electrocute you. Try unplugging the leads from your HV output and listen for any hissing noise. If you hear it, you need to insulate better.
he really do not care about fire safety, if he did he would never have burn that stick over the bed... lucky for him something didn't flew off the wooden stick and landed on the bed....
btw, where is the fun?
the only thing we see are some sparks and some damn high pitch annoying sound.. atleast take down the sound on the sound the sparks generates!!
I tried doing something similar with seven nine-volt batteries connected in series, but I didn't even manage a corona discharge. Awesome video :) Also, accidental spectrograph at 2:33
I have a problem. I think that i made the circuit for my flyback transformer right but theres somethin wrong-It gives out only 19 volts when i use a 9 volt battery! there are sparks but they are only about half a milimeter long. Why it doesn't make normal sparks and big volts?
@loly617 you can find in old TV's ,however you have to be extremly carefull pulling it out cause it stores energy just like capacitors , you need a big screw driver to prob the two terminals so you uncharge it. be careful .
@clienthax Wind your own primary and feedback coil up, fire it up, take a ground wire at the end of a long insulated stick and look for big purple sparks.
Man I wish I had time to do idiotic stuff like this! My projects usually have a little more purpose in life than this too! BACK TO WORK FOR ME> ! My AC Hi POT will do these tricks.
(jack). its ok we have this transformer to bring it back alive!!! turn on the electric fields!
(jim) ok zzzzzzzzz,,,,,,,,,,,,,zzzzzzz,,,,,,,,,zzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzz,,,,,,,,,zzzzzzzzzzz,,, (jack) its alive!!!! wait nvm its dead agian F*** Turn the camera off!
i'm trying to build a "plasma speaker" for an electronics project. we have all the parts (and schematic) in hand, and we're not sure how to set up the flyback transformer. we know for the "singing arc", one end is the thick red cable that runs out of the flyback, but where does the current from this cable jump to? it appears in this video that it jumps to one of the metal pins on the transformer itself. any tips would be appreciated!
@jaredtkatz It goes to the ground pin. We made one from an oscilloscope when I was in electronics school. Just pull the anode from the crt then let it short to ground while injecting audio through the input. It works better if you let it arc through a flame though as the ionized gas aides in sound production....
I'm missing something here. Mine has the high KV output red and an orange and white. I don't see a ground, but assumed white. Is this correct, or is orange and white feedback/primary? Is ground one of the pins underneath? I've got an oscillation circuit I made with just a audio transistor with a oscilation control pot hooked to some power darlington transistors. HELP!
you have to test shortened / bring the HV wire near to each potted terminals to find out which one is the HV ground. If there are arching occur, then that may be the HV GND.
No, you need a fast switching circuit (oscillator) to make them arc/spark. Some use a 555 timer or an audio transistor setup: Subscribe to "lidmotor" videos and he has it both ways.
Just because you breathe a LITTLE of it does not mean that it's not doing anything to you (you dont have to die for it to be effecting you).
Just being "slightly" poisoned WILL cause your health to deteriorate, shorten your lifespan, cause brain damage, nerve, neurological damage, etc... even if you don't notice it right away.
And when you start developing problems you wont remember where you got them from.....
the flyback transformer arc burned you from the inside ( internal burns) the human brain doesent feel burning pain because of the flybacks frequencies, usually in the range of 17 kHz to 50 kHz
i don't get it? my flyback only has an arc of about 5mm and my other only gives off about 1mm? i tried every feedback and primary and tried different polarities! what's the deal!?!?!?
Why what? -- fire + beds don't mix too well. You just don't know what will happen, always safer to conduct experiments like this on a hard surface, even a dirty old board. Not a piece of paper and a bed...
Provides numerous positive charges at the anode (front of the screen) to attract the negative electrons produced at the cathode (skinny "tube" in the back) and thus producing a picture when the negative meets the positive. it also makes a constant sound similar to those sparks.
this energy can kill someone, if it can melt the tip of a tungsten electrode - used for welding - then that means there's alot of energy around that part, I'm building a singing arc by the way so I know a little about that :P
In this design, yes it is needed. In the ZVS circit, it is not. It feeds back into the transistor, allowing the circit to oscillate at the flybacks resonant frequency.
man, i've tried everything to get flybacks to work! i have three here (one with a cracked ferrite core) and two other that are fine. i drew the line when i wasted $5 dollers on a transistor (MJE13009) and it didn't work worth a shit! someone please explain to me why the hell it isn't working! and the one that cracked was a green dot flyback too! also give me suggestions on what i can use to make this thing work.
do what I did, find at least 3 of that transformators. Connect them to get higher current, mage yourself power supply with adjustable friequency and than you can get 15cm long sparx ;)
i hear some tasty jungle
happykyle49 5 days ago
dont put that much current to such a tin wires they will get very hot and melt!
MrTrollfacedeluxe 6 days ago
at 2:45, the legit way to burn a cd
macho844 6 days ago
How to connect the pins of a flyback Transformer using a 9V and resistor to create 3000V?I want to know how the pins must be connected of a flyback transformer. I have the wires, 200Ohm and 20 Ohm resistors, switch and transformer. I have everything but I wanna know how to connect it.
9MrkEgpt4 1 week ago
Your about as bad as me... awesome video lol
voradeaur 2 weeks ago
You ought to build a better enclosure. Current can flow through air without any visible arc. This can be observed by holding your output conductors far enough away that an arc can't be created, and you will hear a hissing noise. These are ion currents, and they CAN electrocute you. Try unplugging the leads from your HV output and listen for any hissing noise. If you hear it, you need to insulate better.
yourTIV0 4 months ago
you a jungle man??
dnbrhythm 4 months ago
is that enough to kill or hurt someone?
mathscirocks 5 months ago
Dude, your bed is not a workbench. Setting stuff on fire on your bed really isn't clever.
beeble2003 5 months ago
This is how i load my mobile battery! :D
Playsim1234 5 months ago
I used 10 urns of primary, and 5 turn of feedback, and it worked fine.
Then I used 5 turns of primary and 3 turns of feedback,, and it didn't work.
How come? :S
kmncztms 6 months ago
You can even literally slice the insulation on wires :D
kmncztms 6 months ago
the fuckin power went out at my house while watching this stupid storms ive got storms all week comin in
crashyboi 6 months ago
he really do not care about fire safety, if he did he would never have burn that stick over the bed... lucky for him something didn't flew off the wooden stick and landed on the bed....
btw, where is the fun?
the only thing we see are some sparks and some damn high pitch annoying sound.. atleast take down the sound on the sound the sparks generates!!
crankylucifer 7 months ago
4:42 = Schockolate.
NickXDDX 7 months ago
I tried doing something similar with seven nine-volt batteries connected in series, but I didn't even manage a corona discharge. Awesome video :) Also, accidental spectrograph at 2:33
AsymptoteInverse 8 months ago
What are you using as a power supply?
Alex1M6 10 months ago
@Alex1M6 Just a 13.8v 5A supply
sparkie21 10 months ago
wooow
htupam 11 months ago
Can you cut tin foil using a flyback transformer? And how about etching pcb's?
raguaviva 11 months ago
It's alive ! :D
madmax10101 11 months ago
I have a problem. I think that i made the circuit for my flyback transformer right but theres somethin wrong-It gives out only 19 volts when i use a 9 volt battery! there are sparks but they are only about half a milimeter long. Why it doesn't make normal sparks and big volts?
RRdigy 11 months ago
This has been flagged as spam show
fun fun fun
denner610 11 months ago
Electrifying experiment...GOT IT?ELECTRIFYING?HUH?ANYONE?OH,C'MON...FUCK THIS SHIT, I'M GOING TO MOON...
4540524 1 year ago
how much is the input?i want to see if i can built one
bernardocovas 1 year ago
So could i get the off of any old LCD TV i.e computer monitor? If so where is it located?
loly617 1 year ago
@loly617 you can find in old TV's ,however you have to be extremly carefull pulling it out cause it stores energy just like capacitors , you need a big screw driver to prob the two terminals so you uncharge it. be careful .
alitou001 1 year ago
Your hotstick seems rather optimistic ;)
pieznice29 1 year ago
fascinating
m4astermisch4 1 year ago
isn't this the basis for the plasma speaker??
mrfuzzles92 1 year ago
hea mate
ive got one of these and i cant find the datasheet anywhere
im making a plasma speaker with mine after i get the pins located
any tips?
clienthax 1 year ago
@clienthax Wind your own primary and feedback coil up, fire it up, take a ground wire at the end of a long insulated stick and look for big purple sparks.
yTubeBlowsBigBalls 1 year ago
i have a question can this kill some one ???????????
1212fdfd 1 year ago
@1212fdfd no question about it
alitou001 1 year ago
hhaha jacobs ladder from cartoons... mmm...frankenstein
izlude2 1 year ago
if you lose this flyback may i have it?
robot797 1 year ago
reminds me of tesla coil
adamz1988 1 year ago
You might want to add a walton cocroft voltage multiplier to that, then you could have some real fun if you dont kill yourself first.
element2310 1 year ago
0:38 reminds me of the gravity gun
apard7 1 year ago
primary coil is WAYYYY to thin.
TeravoltOrg 1 year ago
Holy crap, that's badass.
avwos 1 year ago
i heard its impossible to do that to your hard drive i bet you 100$/£ that you cant
custom91911 1 year ago
pa que sirve?
2gogy 1 year ago
@2gogy
para muchas cosas
puedes hacer plasma, encender un fluorescente a distancia (pequeña).. dar calambrazos..hacer un ignitor a lo grande..
en fin..
Worge993 1 year ago
sounds like a lightsaber! hahaha
rfsdalotto 1 year ago
cool!! wabba make one of these!
MaryStewart 1 year ago
Nice job man! good setup too!
xXINSANELOSERXx 1 year ago
I was worried about sending my phone off for recycling, I now know how to erase the memory.LOL
vivanetx 1 year ago
Man I wish I had time to do idiotic stuff like this! My projects usually have a little more purpose in life than this too! BACK TO WORK FOR ME> ! My AC Hi POT will do these tricks.
Satchmoeddie 1 year ago
cell phone!!
Doctor its dead!
(jack). its ok we have this transformer to bring it back alive!!! turn on the electric fields!
(jim) ok zzzzzzzzz,,,,,,,,,,,,,zzzzzzz,,,,,,,,,zzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzz,,,,,,,,,zzzzzzzzzzz,,, (jack) its alive!!!! wait nvm its dead agian F*** Turn the camera off!
sonicxlc123 1 year ago 16
@sonicxlc123 Haha brilliant :)
sparkie21 1 year ago
@sparkie21 hey um mr. awesome what power supply do you use cuz i want to make this and zap bugs
TheJd45 1 year ago
@sonicxlc123 LMAO ! XD
AiRGuNmOdEr 1 year ago
I'm notsure but I don't think that's how you're supposed to burn a CD.
tryithere 1 year ago
thats how you burn a vd!
pokemonaca 1 year ago
Dude, on your bed? Hope you had a fire extinguisher handy!
perldude69 1 year ago
i have that exact same nail :) home depot?
flargrbargr 1 year ago
caN u help me with how this works please and what component goes were..what coils to hook up
metaltomato100 1 year ago
@metaltomato100 Google 2N3055 Flyback Driver
Its a very simple circuit.
sparkie21 1 year ago
Comment removed
usernameABCDXYZ 1 year ago
@sparkie21 i found the powerlabs driver but i could not find the right resistors. is there another circuit with more common resistor values?
mathscirocks 5 months ago
i tried this before and the but the candy bar wrapper i used caught fire o.o
randommezos 1 year ago
mmm... tasty ozone addictive
coolaidkiller101 1 year ago
hi,
i'm trying to build a "plasma speaker" for an electronics project. we have all the parts (and schematic) in hand, and we're not sure how to set up the flyback transformer. we know for the "singing arc", one end is the thick red cable that runs out of the flyback, but where does the current from this cable jump to? it appears in this video that it jumps to one of the metal pins on the transformer itself. any tips would be appreciated!
jaredtkatz 2 years ago
where did you get plans ive been trying to find the for ages
panzuman 2 years ago
@panzuman Just google: 2N3055 flyback driver
sparkie21 1 year ago
@jaredtkatz It goes to the ground pin. We made one from an oscilloscope when I was in electronics school. Just pull the anode from the crt then let it short to ground while injecting audio through the input. It works better if you let it arc through a flame though as the ionized gas aides in sound production....
ArtistBlade1972 1 year ago
The chocolate wrapper reminds me of darth vader picking up the emperor and chucking him off the rail in star wars :D
SimOfDark 2 years ago
I touched TV's flyback tranz wire... It hurts
TheError404 2 years ago
that looks fun!!!!! =P
chickenpoper 2 years ago
I'm missing something here. Mine has the high KV output red and an orange and white. I don't see a ground, but assumed white. Is this correct, or is orange and white feedback/primary? Is ground one of the pins underneath? I've got an oscillation circuit I made with just a audio transistor with a oscilation control pot hooked to some power darlington transistors. HELP!
LoneOarman 2 years ago
Do flyback transformers emit any radiation/xray when operating and when arcing?
Driv3th3hiv3 2 years ago
they do inside a vacuum but other than inside one they do not produce any amount of x-ray radiation
zker666 2 years ago
Many who play with these things use a protective cage or box.
LoneOarman 2 years ago
you have to test shortened / bring the HV wire near to each potted terminals to find out which one is the HV ground. If there are arching occur, then that may be the HV GND.
mekir87 2 years ago
so flyback transformers plug right into the wall when you take them out of a tv?
MacsCanfly 2 years ago
i dont think they do :(
guydie5 2 years ago
This has been flagged as spam show
Do flyback transformers emit any radiation/xray when operating and when arcing?
Driv3th3hiv3 2 years ago
no no no no no! never put a flyback strait into and outlet. you need a dc current and a flyback driver. google it
zker666 2 years ago
This has been flagged as spam show
Do flyback transformers emit any radiation/xray when operating and when arcing?
Driv3th3hiv3 2 years ago
This has been flagged as spam show
Do flyback transformers emit any radiation/xray when operating and when arcing?
Driv3th3hiv3 2 years ago
No, you need a fast switching circuit (oscillator) to make them arc/spark. Some use a 555 timer or an audio transistor setup: Subscribe to "lidmotor" videos and he has it both ways.
LoneOarman 2 years ago
This is why CRT's rule
jonnyj0987654321 2 years ago
This has been flagged as spam show
Do flyback transformers emit any radiation/xray when operating and when arcing?
Driv3th3hiv3 2 years ago
nice that high voltage has nice corona wind
zker666 2 years ago
This has been flagged as spam show
Do flyback transformers emit any radiation/xray when operating and when arcing?
Driv3th3hiv3 2 years ago
Idk why di you post tthat like 6 times
guydie5 2 years ago
love the smell of ozone its addictive taste a bit like blood
coolaidkiller101 2 years ago
nooooooooooooo!! not a nokia 6230 nnooooo the nice cellphone
tbsys31061 2 years ago
yeah but it can be deadly if y smell to much :))
raxredneck 2 years ago
Yeah, deadly.
But as with all poisonous things:
Just because you breathe a LITTLE of it does not mean that it's not doing anything to you (you dont have to die for it to be effecting you).
Just being "slightly" poisoned WILL cause your health to deteriorate, shorten your lifespan, cause brain damage, nerve, neurological damage, etc... even if you don't notice it right away.
And when you start developing problems you wont remember where you got them from.....
RhXz47rc 2 years ago
Doesn't everyone here agree that ozone smells lovely?
holycrapapie 2 years ago 28
This has been flagged as spam show
@holycrapapie indeed. i LOVE smelling ozone lol
MrPablo3771 1 year ago
@holycrapapie it smells somewhat like bleach to me. and it isn't good to inhale a lot of it
mathscirocks 6 months ago
I wonder if you could use this to clean the tartar and plaque build-up off your teeth. Do you think it would whiten your smile?
PigsCanFly99 2 years ago
for sure
ratingssuck 2 years ago
also can you post a vid on how you made everything
collinwashburn 2 years ago 7
what was your power source
collinwashburn 2 years ago
Thats friggin awesome
Chiefhalo19 2 years ago
thin cables for such a high voltage
myztic123 2 years ago
its doing something to the camera...
thecssnoobz 2 years ago
my huge crt tv flyback produces 40kv
438426x1 2 years ago
that fucking kicks arse
gunman305 2 years ago
Check out my Flyback Transformer connected to a VoltageTripler.
voon100 2 years ago
Was that NOKIA6230 ? I't a good phone !
jarkonkotisivu 2 years ago
u have safe place to burn wood:DD
TheoZc1 2 years ago
looks like you had a lot of fun!
suupertramp 2 years ago
Now try touching it. Joke. Nice thingy majiggy there.
scozzahisee 2 years ago
a color tv flyback generates more juice but you can also try ramping up the input voltage as well with using the same flyback.
hellsmaw84 2 years ago
pure RF
stranac1 2 years ago
at 1:23 is the cell screen lighting up
bill0chatham 2 years ago
Bom pra desbloquear telefone celular...
h4cker10 2 years ago
mmmm beautiful boxed, nice arcs
ruggeromaestrini 2 years ago 2
do you use some special material and shape for the electrodes, or is it just normal metal in a pointy shape?
LMF5000 2 years ago
i can only get 1cm arcs! god dammit
Ravenpulse 2 years ago
me too. Any ideas?
Aleksa809 2 years ago
put 2 turns on the primary and see what happens
masermaker97 2 years ago
The coolest part is when the CD got burned through and it started arcing across the gap
mdemenok 3 years ago
pain doesnt operate on frequencies....
razzsupermccool 3 years ago
sweet one!!!
SmashCOBamberg 3 years ago
next make a emp pulse weapon :D
legomaniac150 3 years ago
what do you mean with "fun" the fun ends when someone gets killed. playing with arcs its no fun at all.
predator2036 3 years ago
It doesn't have to go that far, maybe he's happy just frying random crap.
Btw arcing IS fun
holycrapapie 2 years ago
nope, not near enough power
zanta24 3 years ago
oh... and how to power a flyback?!?
SmashCOBamberg 3 years ago
use google and search "flyback driver" :D
zanta24 3 years ago
I did the same... but yesterday I touched the the flyback by mistake... OMG!!! That was a "shocking" experience
SmashCOBamberg 3 years ago
the flyback transformer arc burned you from the inside ( internal burns) the human brain doesent feel burning pain because of the flybacks frequencies, usually in the range of 17 kHz to 50 kHz
predator2036 3 years ago
lol, tape it to someones chair
legomaniac150 3 years ago 2
i don't get it? my flyback only has an arc of about 5mm and my other only gives off about 1mm? i tried every feedback and primary and tried different polarities! what's the deal!?!?!?
ikilljewbabies 3 years ago
can u make 1 of these?? or do u buy? if so where?
konabiker9 3 years ago
u get the complese curcit out of a tv or computer monitor
Durken316 3 years ago
you needn´t to buy one... Flybacks can be found in every monitor...
SmashCOBamberg 3 years ago
Didn't some older televisions use flyback transformers? I think I might have one and I'm wondering if it can be repaired.
piper4seeformerly 3 years ago
how i made a tesla coil with a flyback?
rubas07 3 years ago
fascinating. makes you think that ufo like tech is possible
DanFrederiksen 3 years ago
and all of that out of a 2n3055?
my won't go for that long arc's.
only now i used some other transistors.
zezimashock 3 years ago
Urgent Help needed!
Where to buy/find flyback transformer
Philips AT2140/16 ?
Zahlvater 3 years ago
You can found flybacks in an old CRT television.
But the best flyback are in the old black and white CRT televisions.
Bye, Arma ^^
ArmaHighVoltage 3 years ago
Nice transformer :)
Can you post the schema of this driver?
Thank
Arma ^^
ArmaHighVoltage 3 years ago
Hey I'm pissed! I tried this on my new cell phone and now it doesn't work! LOL
gedgar2000 3 years ago 3
I guess that CD doesn't work anymore... :)
Aze876 3 years ago
Wow that's impressing !!!
(U use the dark side of the force)joking
matdb001 3 years ago
Super excellent arc man well done
sheumatic 3 years ago
you need to get a flyback from a tv and still on curcit bord, it works better, :D
Durken316 3 years ago
my fly back makes 1 inch arcs i zaped myself and i jumped im alive ritting this commment
stutest2 3 years ago
OK, cool... however, why did you conduct the experiments on your bed and not a hard surface? (ie: a concrete floor) lol
natenorrish 3 years ago
why?
Durken316 3 years ago
Why what? -- fire + beds don't mix too well. You just don't know what will happen, always safer to conduct experiments like this on a hard surface, even a dirty old board. Not a piece of paper and a bed...
natenorrish 3 years ago
tru if you touch leads on the cap it will hurt like hell
Durken316 3 years ago
Poor phone :(
stalkersas 3 years ago
can i get the circuit plans?
Ztuibyman 3 years ago
on 0:23 it looks lighter than 0:26...
alwinovich 3 years ago
If you like this, then you would properly get off, on a job as a welder
Wollemand 3 years ago
Mmmm. Sparks.
Wonderful. Areal beauty of a flyback.
Arexux 3 years ago
0.006 AMP across the heart will kill u.
how do i make one of these things?
imaqtlolz 3 years ago
1-5 miliamp, but heart fibrilation starts @ 30mA
alwinovich 3 years ago
CAN THIS KILL A PERSON??
Atomic101Heli 3 years ago
Not sure, im not trying! Guess it will really hurt at least ;)
sparkie21 3 years ago
what does the flyback transfomer do for the crt monitor?
slaterking1000 3 years ago
Provides numerous positive charges at the anode (front of the screen) to attract the negative electrons produced at the cathode (skinny "tube" in the back) and thus producing a picture when the negative meets the positive. it also makes a constant sound similar to those sparks.
mohammeddavis 3 years ago
Oh ok well ok thats ok i guess
Atomic101Heli 3 years ago
It wont kill someone, because the amperage gets lowered tremendously to make such high voltage. But it will cause violent muscle spasms.
BTW, this is not from personal experience.
Chamtechie 3 years ago
this energy can kill someone, if it can melt the tip of a tungsten electrode - used for welding - then that means there's alot of energy around that part, I'm building a singing arc by the way so I know a little about that :P
TheDexboy 3 years ago
what is the purpose of a feedback coil? Is it needed?
Thanks, great video.
BasementBen 3 years ago
your tv needs it
jaa93997 3 years ago
In this design, yes it is needed. In the ZVS circit, it is not. It feeds back into the transistor, allowing the circit to oscillate at the flybacks resonant frequency.
sparkie21 3 years ago
put a flash tube in that
lasergeak 3 years ago
HAHa that was fun try doing it with a dynamite set xD
HellNukes 3 years ago
lol
jaa93997 3 years ago
Aww this gotta be fun... And looks simple to build too...
Guess i'll do something like...
exjio 3 years ago
please can you tell how do you identify the feedback, primary coil and secondary base pins on a 15 pin flyback? please reply
SKarmytech 3 years ago
No wonder they call the energy bars!
TheGeek1028 3 years ago
does a pc monitor also have a flyback? (not lcd but the older ones ^^) nice vid by the way, inspired me a lot lol
OGMO11 3 years ago
it depends if its a CRT it has a cothodic tube so it needs flyback, if its plasma or LCD it doesn't
SKarmytech 3 years ago
man, i've tried everything to get flybacks to work! i have three here (one with a cracked ferrite core) and two other that are fine. i drew the line when i wasted $5 dollers on a transistor (MJE13009) and it didn't work worth a shit! someone please explain to me why the hell it isn't working! and the one that cracked was a green dot flyback too! also give me suggestions on what i can use to make this thing work.
nordo360 3 years ago
do what I did, find at least 3 of that transformators. Connect them to get higher current, mage yourself power supply with adjustable friequency and than you can get 15cm long sparx ;)
thesmellmaker 3 years ago
I have a "destroyed" 17 inch crt (my brother shot the screen) and I want someone to tell me how to do this!! PLEASE!
Hrakleus 3 years ago
sweet. nice done... wonder what a frog would do...
gobuyone 3 years ago
that was AWSOME but if you get it out of a tv make sure the cirular thing that goes over th bulb is still on.
makes bigger/better arcs.
BTW check out my dads vid.
go to my channel and under friends look for toommyg155
Durken316 3 years ago
i was waitin for he wrapper part. ive done what with a modded bug zapper, just like 630v. nice sparks though.
as a suggestion..
try it with low light.
cook some raw chicken!
BACON!
yz250ftony 4 years ago
That would make a nice jacobs ladder. Do you want to sell it?
mca0824 4 years ago
Doing that to a CD is better than putting it in a microwave! :D
PepsiYoshi 4 years ago 2