Marshall MS-2 Mod More Highgain

[TheIbanezGrx20]

the intro is like Some kind of monster :D

[felphero]

MAXIMUM THE HORMONE!!!!!!!!! fucking awesome! HAHA

[DownTicH4rri3r]

Where can i get a small cable for this so i can have it in on a belt?

[boredtodelusionFan]

Does it have a clean tone?

[yamahabmxer1]

@boredtodelusionFan yes

[homersimps1]

Sounds better than every Line 6 I've heard.

[Belleraphon100]

@homersimps1 get your ears tested

[bullshitproof]

@homersimps1 damn right.

[SteelPandaThommo]

i have no idea how to do this to an amp i wish i could :(

[wandercamilotto]

sound is good of ms-4

[saskekun101]

does it need a plug XD

[afikiota]

My amp led is red! I want the blue one

[BMXBOBO]

im on that weird part of youtube again

[cmzangetsu1993]

Fucking Playing Shimi through the that little beast! Hells yes

[JoystixMusic]

Lol, I'd love to see someone put this ontop of a 4x12 and use a power amp to pwer the cab, but have this provide all the tone. Is that even possible?

[bezoro2008]

this is impressive for such a small amp

[UnitedHateLv]

i bought this for for about 38$ at a music store. Was so worth it.

before i left my old band, the bass player lived on the other side of the city, so this thing was really handy, when we had to go to his place.

[leonixsc]

ahhahahahah lol

[CobrazVeNoMx]

Epic, but I imagine eventually the speaker would blow.

[timberland1108]

what song u playing

[INGAGEN6]

@timberland1108 maximumthehormone.

[INGAGEN6]

@timberland1108 & OZZY , Disturbed ,

[razorrick1293]

i modded mine with a 2.2uF cap accross the transistor emitter resistor, gave a lot more gain, and it doesnt sound too bad

[johnnyblax1]

Yes but you say on your comment ms4. What about the master volume knob you put? Is it a standard guitar pot like Alpha or CTS? Is it a 250 kOhm a 500 or 1MOhm? And where do you connect it? The extra cap what capacity must it be? 470 pF again or something else?

[INGAGEN6]

@johnnyblax1 You 'll have to cut the red wire that connects the "O1" pin of the amp board and the "O1" pin of the out Jack board.Cut it in the middle and strip the 2 cut ends of the wire. Solder the ends to a 4,7kOhm,1W pot (lugs 2 and 3). It would be really good to connect a 47Ohm, 1W resistor to pins "O1" and "O2" of the amp board to serve as a Load and keep the IC's temperature low.

[johnnyblax1]

Amazing? Can you tell me anything about the master volume and the higher gain mode?



[INGAGEN6]

@johnnyblax1 You could modify the ms4's amp board to produce more gain! All you have to do is placing 2 jumpers across the "R1" and "R8" marked resistors of the board. An extra cap could be used in parallel with the 470pF cap(across pins 1 and 4 of the IC/chip) to reduce the "nasty" highs. In case you don't need the gain pot, you could put an extra jumper in parallel with the R4 resistor for even more gain . The amount of gain is controlled by the volume pot in this case.

[Olegga666]

Great sound.

How you mod this? Can you give link?

[INGAGEN6]

@Olegga666 take the resistance of R1 and R8 and join by a jacket pin.