@oldskoolaoldier yea i got mine at 4 wheel parts there like these small little axles dat bold on to ur axles that rase it up wit out putting blocks ill take a video and post so u can c ust luk up my name sire429
Hey bro ust a lil hin to ppl dat wanna do lift to der blazer i got a 2000 ok did a 3 inch lift for under a hundred buck i tighten d suspension in d front dat raised it 3 inches and multiplyed the axle in the rear and it only took me 1hr ust sayin looks gud and cheapper and easier check out my blazer type in sire429
@julesb12345 I actually just used Rocker guard/ asphalt undercoat. I taped the lines around the fenders and sanded them, then sprayed them a few times over a month with the spray can. I did the wheel wells, and the frame too. I don't have any after market fender flairs, just the spray. Thanks for the comment!
like the vid. think I'm looking at the same kit at jc whitney...says its a 2 or 3" kit..same company though " Performance Accessories "....looking at doing on my 1996 s10 blazer 4 dr 4x4...was yours the same 2 or 3" body lift ?
I put mine on sunday- where do I put the side bumper brackets though? I can't figure it out!
El Diablo793 Blazerforum
SuperRetroTech 5 days ago
@oldskoolaoldier yea i got mine at 4 wheel parts there like these small little axles dat bold on to ur axles that rase it up wit out putting blocks ill take a video and post so u can c ust luk up my name sire429
SIRE429 1 week ago
Hey bro ust a lil hin to ppl dat wanna do lift to der blazer i got a 2000 ok did a 3 inch lift for under a hundred buck i tighten d suspension in d front dat raised it 3 inches and multiplyed the axle in the rear and it only took me 1hr ust sayin looks gud and cheapper and easier check out my blazer type in sire429
SIRE429 1 week ago
@SIRE429 Thanks for the comment, what do you mean 'multiplied the rear axle?"
OldSkoolSoldier 1 week ago
do the bolts that came with the body lift bolt into nuts or do they bolt into the body itself?
jrobb913 1 week ago
@jrobb913 The bolts thread into the body itself, thanks for watching!
OldSkoolSoldier 1 week ago
I've had my PA 2" BL up in my attic for about 6+ years now for my 2002 BlaZeR2. Your video has inspired me to just fuckin' install the bitch already.
::favorited::
BobboZR2 1 month ago
question
where did you get the black rocker panel trim and fender flares?
julesb12345 1 month ago
@julesb12345 I actually just used Rocker guard/ asphalt undercoat. I taped the lines around the fenders and sanded them, then sprayed them a few times over a month with the spray can. I did the wheel wells, and the frame too. I don't have any after market fender flairs, just the spray. Thanks for the comment!
OldSkoolSoldier 1 month ago
good video, best one on here.
Sexymanye419 2 months ago 2
Same kit, mine is a 2" body lift
OldSkoolSoldier 5 months ago
like the vid. think I'm looking at the same kit at jc whitney...says its a 2 or 3" kit..same company though " Performance Accessories "....looking at doing on my 1996 s10 blazer 4 dr 4x4...was yours the same 2 or 3" body lift ?
Ricky039 5 months ago
@Ricky039 Yes, I had the Performance Accessories 2" body lift.
OldSkoolSoldier 1 month ago
Fellow blazeeforum member- great vid! How would I get a GMC Jimmy grille off though?
SuperRetroTech 5 months ago
@SuperRetroTech I assume it would be a simple clip system as well. Try to pull the grille a bit and watch down with the hood open.
OldSkoolSoldier 1 month ago
Great vid... But I betcha those 1/2 and 5/16 fasteners you did would be better using a 13 and 7mm instead... Just sayin'
OHSOOOFLY 6 months ago