i have a 14 hp vanguard twin motor and not getting gas i cleaned the carb and checked the fuel pump both seems fine when i put eaither in it it runs for a few secounds and dies off and i hooked the electric silonoid up but still no go can any one help me on this or no where i can send it to get worked on or a rebuild ?i have 4 briggs engines like that 4 sale but black in collor
make sure you buy a good cast iron pulley, or at least a stamped steel one... those crappy cast aluminum ones wear away too quick. Kudos on the spider gear welding - we've been doing lincoln lockers for a few years now :)
Hey i have put on a small pulley on trans. and im having trouble on the engine pulley the shaft is much bigger and goes in the pulley more different. How do i put a larger pulley on it? im stuck on this prob. with tractor kind of dismantled. i want to get back to riding it fun fun.
ummm ya have to get pulley with a bigger hole in it so it fits your motor and to get them off you need a gear puller cause they are usually rusted on get just a single pulley that fits your motor shaft and you have to line it up with the belt and put the keyway in and tighten it down with the hex key and put your belt on, youll need a new belt too to fit it
it can after a while. what i would suggest is fill is with higher speed oil than what is in it, becasue stock grease is only low speed. Also, if you dont need reverse then open your gearbox and remove the chain that connects the reverse gear. This can sometimes become loose and rip apart your gearbox.
you put a bigger pulley on the engine, and a smaller one on the transmission, but i also take my transmission apart and weld the spider gears together
well where did u get bigger pully i see on my mower that the deck pully is bigger sgould i flip them??? and what about the back btw thank you for answering me
go to tractor supply co and get a pulle with the same shaft size as your motor i used a 4.5 in pulley on the motor and i think a 4 in on the transmission
This has been flagged as spam show
whats your transmission? and what do you use for the transmission a belt or a chain?
mouse007hi 1 year ago
that looks fun as hell i want to do it
TYdragons 2 years ago
did you modify the transmission if you did do you know if keeping the stock transmission on will destroy it
DirtbikeGuy2009 2 years ago
how big engine and where did u get it?
nikesandsprite 2 years ago
nah i didnt but either way id have a blaST on those mowers. hgell id even mow my neighbors lawn for free. lol
80cwyk80 3 years ago 4
either vanguard twin or kohler command twin. but def. a twin
budfrogluv 3 years ago 3
that first one had a briggs single if i'm not mistaken and that second one sounded an awful lot like a briggs vanguard twin. both sounded sweet tho
budfrogluv 3 years ago
yeah i agree... but i love how low the first one idles, even for a single.
CSAKvids 3 years ago
daaaaaamn!!!
budfrogluv 3 years ago
whoa those are kick ass lawn mowers. did yall dump bike engines in em or something?
80cwyk80 3 years ago
no their just modified bigger lawnmower motors in them
aspirepower101 3 years ago
@aspirepower101 wat r the pulley sizes?
omaxx12 1 year ago
lmao 80cwyk80, These are hillbillys were talkin about...did u not look at the engine?
EVILSTONERKID 3 years ago
What kind of engine you running in that?
CSAKvids 3 years ago
what is the trans?? is it like a peerless or what?!!? please help very interested.... check out my mower!!!
crazytubadude 3 years ago
it has a motorcycle carb on it, pulleys, a peerless tranny welded,
aspirepower101 3 years ago
This comment has received too many negative votes show
hick
comedykid8485 3 years ago
hahaha, thats hilarious
dkeightpack20 3 years ago
is it possible to make one out of a craftsman II with a 18hp v twin?
jamesb1221222 3 years ago
what size are the pulleys
redmand18 4 years ago
nice, are u shifting gears?? is it a dirrferent, tranny? sounds like an auto matic shifting tranny LOL
Redneckfarmer77 4 years ago
cool lawnmowers.
moon1moon1 4 years ago
what did you do to get it to go that fast?
dirtbikes4life250 4 years ago 2
different pullys
bigtrucks 4 years ago
bad ass
wheelinkid00 4 years ago
how do u make one!!!!
BigHoss3030 4 years ago
thanks
Snoopy0345 4 years ago
will changing the pullys work on a hydrostatic drive mower.
Snoopy0345 4 years ago
it should, if it has pullies. (don't have a hydro)
Dang, my craftsman's are welded on, I can't change them. :(
FirstProject 4 years ago
swee lawn trators how do you make them go that fast!?!?!? the govener???? write me someone. lol
Redneckfarmer77 4 years ago
looks like the govener... or throttle and also the pulleys swapped..
crazytubadude 3 years ago
is that a car exhuast?
pbplayaforlife 4 years ago
chek my lawn mower wheelie
jons9013 4 years ago
This has been flagged as spam show
i have a 14 hp vanguard twin motor and not getting gas i cleaned the carb and checked the fuel pump both seems fine when i put eaither in it it runs for a few secounds and dies off and i hooked the electric silonoid up but still no go can any one help me on this or no where i can send it to get worked on or a rebuild ?i have 4 briggs engines like that 4 sale but black in collor
kasjv 4 years ago
how do you have to gas pedal hooked up
thanks
jungetracin 4 years ago
hey i like ur mower im woking on a 14.5 briggs and need some ideas including your exhaust i want mine just like that.
turrco07 4 years ago
that exhaust went under the mower out the back by the transmission
just a straight pipe no muffler
aspirepower101 4 years ago
i have a 3 speed manual transmission will changing the pullys make it go faster or mess it up?
Snoopy0345 4 years ago
was that a wheelhorse b4 u modded it severely?
Omega481 4 years ago
yea it was!!! : )
aspirepower101 4 years ago
that is fuckin tite
maniakkilla 4 years ago
make sure you buy a good cast iron pulley, or at least a stamped steel one... those crappy cast aluminum ones wear away too quick. Kudos on the spider gear welding - we've been doing lincoln lockers for a few years now :)
therainbowboxer 4 years ago
that looks like fun
kidonthe300ex 4 years ago
Hey i have put on a small pulley on trans. and im having trouble on the engine pulley the shaft is much bigger and goes in the pulley more different. How do i put a larger pulley on it? im stuck on this prob. with tractor kind of dismantled. i want to get back to riding it fun fun.
thanks
300609 4 years ago
ummm ya have to get pulley with a bigger hole in it so it fits your motor and to get them off you need a gear puller cause they are usually rusted on get just a single pulley that fits your motor shaft and you have to line it up with the belt and put the keyway in and tighten it down with the hex key and put your belt on, youll need a new belt too to fit it
aspirepower101 4 years ago
What mods can u do to the engine?
I read some rules and they wouldn't let u even change the carb, or would that be a different type?
Be good if u could put bigger carb, freeflow zaust, high ratio/lift rockers etc?
tpvalley 4 years ago
just change pulls small back big front
shamuslauer1 4 years ago
would my gearbox brack if i was going to make it faster
samuelweightman 4 years ago
NOPE!
shamuslauer1 4 years ago
it can after a while. what i would suggest is fill is with higher speed oil than what is in it, becasue stock grease is only low speed. Also, if you dont need reverse then open your gearbox and remove the chain that connects the reverse gear. This can sometimes become loose and rip apart your gearbox.
CSAKvids 3 years ago
is your mower lowered any ?
domarias 4 years ago
yea a little bit
new axles in the front and the seat springs out on the one
aspirepower101 4 years ago
u gotta cut the front end in half and add 5 inches to widen it and then weld it sold to the frame if u move it up it will lower the front by a lot
chrisfarlywannabe 4 years ago
i have remover the deck of my lawnmower now waht do i do??(for speed)
shamusherba 4 years ago
u have to put a smaller pully on the tranny and a bigger pully on the motor
chrisfarlywannabe 4 years ago
what kinda tires r that
atverdude 4 years ago
just v tread lawnmower tires
aspirepower101 4 years ago
whereu get??
shamusherba 4 years ago
what tires r on that
atverdude 4 years ago
Big pully on the engine... little pully on the tranny... :p
Marks256 4 years ago
yep yep
aspirepower101 4 years ago
ivwe heard of that how do you do it???
shamusherba 4 years ago
you put a bigger pulley on the engine, and a smaller one on the transmission, but i also take my transmission apart and weld the spider gears together
aspirepower101 4 years ago
well where did u get bigger pully i see on my mower that the deck pully is bigger sgould i flip them??? and what about the back btw thank you for answering me
shamusherba 4 years ago
go to tractor supply co and get a pulle with the same shaft size as your motor i used a 4.5 in pulley on the motor and i think a 4 in on the transmission
aspirepower101 4 years ago
how did you make it go so fast
57vett 4 years ago
how the fuck did u make it up that hill do u have four wheeler tires on that bitch
elliotcr 4 years ago
radical dood
Brian12Pearson12 4 years ago
How you Drive lawnmower going fast?Because I has lawnmower going only 8 miles for hour lol..
JCxShadow 4 years ago
that looks like fun, i want to race you
JackofSpades014 5 years ago
no shit
ratrodder13 5 years ago
your all muddy
richard4195 5 years ago