I'm willing to bet it's not the header flange gasket. Your pipe is just all bent to hell and you're probably running rich as shit, it doesn't seat right like how you said and it's just spraying spooge right out of the gap. And that dent is ruining your scavenging which is the whole point of the expansion chamber and is also causing this because the gases (and oil that shouldn't be there) cannot escape. I bet that silencer packing is all but burned out or saturated with the same oily mess.
@StreetFighter85 Thanks for the tips, the only thing i know about the richness is that the guy said to run 34:1, and he said that there was a problem at some point (3 years ago) where it was fouling the shit out of the plugs. I'm looking into a new pipe, or a better used one, and going to repack my thingy, once i can get the darned thing off....
@apricotsnms516 fix the pipe situation, then pick a premix ratio. I run ~36:1 and then jet the bike correctly for that mixture. If everything is right there should be little to no smoke or spooge.
dude you propably use the wrong 2 stroke oil and it dosnt burn properly so it drips the shit over the whole bike. Get motul 710 or motul 800.
The springs hold the exhaust because the resonant frequency is so high that the normal screws would unscrew itself. This is also on my 2 stroke and i can help you with the problems if you have any. Just first you can do is warm the bike up properly and then run it full trottle and shut it of and show me the color of the spark plug tip
@warezvz Thanks dude, I've actually tried using the only types of oils we have in my area, one I'm using right now is crap haha the other was Klotz, and that was pretty good. I'm getting new springs and a new gasket, the other thing I didn't say is that the screws holing the joint flange on were VERY loose, I could unscrew them with my fingers! And as for the spark plug, it's a darker beige :)
Thanks again, and I will ask if I ever have any other problems with it!
@apricotsnms516 dude thats a 2 stroke enduro engine it will seize and take hevy damage if you put shit in it. Get propper oil like motul 710, 800 or repsol competition put atleast 2.5-3% if you mix it manualy. Your spark plug should be the color of dry coffe powder after you run it full trottle. The unscrewing screws is the problem that i told you about get loctite cream and cream them before you screw them in. Also change the piston rings they dont cost much but its good to change them.
@warezvz Well, the problem with that oil is I can't get it anywhere locally, so it adds an extra $5 for shipping.. and I'm already low on money as it is, that's why I got crap oil this last time. and yes you HAVE to loctite the screws in!! learned that the hard way! lost my mud guard lol... and again, i'll get the piston when it comes time, but i really don't have an extra $125 sitting around haha which is about two weeks pay.
kool bike.
larrythelookout 10 months ago
@larrythelookout thanks dude! Can't wait till it's up and running! It's gonna be sweet!
twistedkeys1 10 months ago
I'm willing to bet it's not the header flange gasket. Your pipe is just all bent to hell and you're probably running rich as shit, it doesn't seat right like how you said and it's just spraying spooge right out of the gap. And that dent is ruining your scavenging which is the whole point of the expansion chamber and is also causing this because the gases (and oil that shouldn't be there) cannot escape. I bet that silencer packing is all but burned out or saturated with the same oily mess.
StreetFighter85 10 months ago
@StreetFighter85 Thanks for the tips, the only thing i know about the richness is that the guy said to run 34:1, and he said that there was a problem at some point (3 years ago) where it was fouling the shit out of the plugs. I'm looking into a new pipe, or a better used one, and going to repack my thingy, once i can get the darned thing off....
apricotsnms516 10 months ago
@apricotsnms516 fix the pipe situation, then pick a premix ratio. I run ~36:1 and then jet the bike correctly for that mixture. If everything is right there should be little to no smoke or spooge.
StreetFighter85 10 months ago
Left you a comment on Thumpertalk. Pacific pipe repair, high temp RTV silicone sealant, repack silencer, ratio rite, tune, go from there.
StreetFighter85 10 months ago
dude you propably use the wrong 2 stroke oil and it dosnt burn properly so it drips the shit over the whole bike. Get motul 710 or motul 800.
The springs hold the exhaust because the resonant frequency is so high that the normal screws would unscrew itself. This is also on my 2 stroke and i can help you with the problems if you have any. Just first you can do is warm the bike up properly and then run it full trottle and shut it of and show me the color of the spark plug tip
warezvz 10 months ago
@warezvz Thanks dude, I've actually tried using the only types of oils we have in my area, one I'm using right now is crap haha the other was Klotz, and that was pretty good. I'm getting new springs and a new gasket, the other thing I didn't say is that the screws holing the joint flange on were VERY loose, I could unscrew them with my fingers! And as for the spark plug, it's a darker beige :)
Thanks again, and I will ask if I ever have any other problems with it!
apricotsnms516 10 months ago
@apricotsnms516 dude thats a 2 stroke enduro engine it will seize and take hevy damage if you put shit in it. Get propper oil like motul 710, 800 or repsol competition put atleast 2.5-3% if you mix it manualy. Your spark plug should be the color of dry coffe powder after you run it full trottle. The unscrewing screws is the problem that i told you about get loctite cream and cream them before you screw them in. Also change the piston rings they dont cost much but its good to change them.
warezvz 10 months ago
@warezvz Well, the problem with that oil is I can't get it anywhere locally, so it adds an extra $5 for shipping.. and I'm already low on money as it is, that's why I got crap oil this last time. and yes you HAVE to loctite the screws in!! learned that the hard way! lost my mud guard lol... and again, i'll get the piston when it comes time, but i really don't have an extra $125 sitting around haha which is about two weeks pay.
apricotsnms516 10 months ago
@apricotsnms516 dont ride it on the crap oil because if the crankshaft burns out trust me its gonna be expansive
warezvz 10 months ago
@warezvz Thanks for the tips bro I will keep that in mind.
apricotsnms516 10 months ago
Nothing like I have ever worked on myself.
Best of luck in getting it up and running bro.
suburbanryder 10 months ago
@suburbanryder Thanks Chuck! I'm looking forward to the riding season this year!
apricotsnms516 10 months ago