Free energy has been here all along ,But the Oil companies want these technologies unknown to the masses,Get a motor that works with the power of magnets only at LT-MAGNET-MOTORdotCOM ,Join the energy revolution!
yes,,I agree,, its best fill some caps up then switch it over to run on the caps power. and see if it can fill it faster than it can use it,, Good job!!!
Right now I am not playing around so much with capacitors.. Although I have in the past with my first Newman Motor and got some good results! This time I'm simply trying to charge a rechargeable 9V battery and have it charged enough to run the motor once the AA batteries run out.. if I can do that, Im totally sold on this technology!
Went out and bought some A/C caps rated at around 800V and also picked up tons of various sized D/C caps.. going to use the caps as a dump bucket for the big voltages I am getting back from this and see if I can put it to use.. I have to brush up on diodes, resistors and charging circuits.. back to the books!
I think it all has to do with timing and pulse duration. With this motor I only pulse the 6V once per revolution instead of twice like it's "supposed to be" switching polarity.
I think this allows for less overall draw on the batteries although I will try different commutator configurations for fun and see what happens. I also have a generator on the end of it that independantly puts out about 2-3.5V which would otherwise be wasted (next vid I will show this) Thanks for the positive comments
I'm not sure why it lasts for 2 days at this point, I know I am drawing only about 20miliamps with the proper commutator timing. I have added more wire to the main coil, aprox 500 more feet. The resistance has gone up but now draws even less from the battery. I did notice as you go with more windings in the coil, amperage goes down as long as the voltage is higher to keep the RPM's up.
I have measured A/C voltage spikes with the bigger coil at over 1000v!! Off the meter..
The "motor" will actually spin slowly off of 1 AA battery 1.5V - so to answer your question, it will technically run off of what 1 AA will provide as far as amps..
I will be taking more measurements and will post up the results.
To properly answer the question you could build a circuit that's used only for measuring the REAL power consumption of your motor. I explain how to do it on one of Armakuni2000's clips.
Excellent work! Like Nonetub, I'm in the Bedini SSG mode right now but I started out with a Newman motor first. I'm using AA batteries to run my SSG so your project interest me alot.
Great job TheB3e!!! You show in this video how a better design can put more output energy... You show here how easy is to make an overunity device. You can post how to replicate you experiment in our NERD forum. Now, I´m working in the same idea, but using the Bedini motor. I want to compare what experiment can put more output energy, Newman or Bedini? Look in my uploaded videos and see my video about Bedini Motor/Generator to get an idea.
This has been flagged as spam show
Free energy has been here all along ,But the Oil companies want these technologies unknown to the masses,Get a motor that works with the power of magnets only at LT-MAGNET-MOTORdotCOM ,Join the energy revolution!
checksummedchest 1 year ago
yes,,I agree,, its best fill some caps up then switch it over to run on the caps power. and see if it can fill it faster than it can use it,, Good job!!!
Bill- N.e.R.d Group
MoonSpyStudios 3 years ago
Right now I am not playing around so much with capacitors.. Although I have in the past with my first Newman Motor and got some good results! This time I'm simply trying to charge a rechargeable 9V battery and have it charged enough to run the motor once the AA batteries run out.. if I can do that, Im totally sold on this technology!
Thanks for the positive feedback!
TheB3e 3 years ago
Went out and bought some A/C caps rated at around 800V and also picked up tons of various sized D/C caps.. going to use the caps as a dump bucket for the big voltages I am getting back from this and see if I can put it to use.. I have to brush up on diodes, resistors and charging circuits.. back to the books!
TheB3e 3 years ago
700 feet of wire in 20AWG is 7 ohms!
700 feet of wire in 20SWG is 5.6 ohms!
How do you run 6 volts of batteries on so few ohms for days???? :)
I need this. My coil is 270 ohms and I'm using 40 volts of AA batteries just to run it for two or three days!
Like Lidmotor, I am very curious as to what amount of current you are using. Please show AC and DC.
Awesome!
kmarinas86 3 years ago
I think it all has to do with timing and pulse duration. With this motor I only pulse the 6V once per revolution instead of twice like it's "supposed to be" switching polarity.
I think this allows for less overall draw on the batteries although I will try different commutator configurations for fun and see what happens. I also have a generator on the end of it that independantly puts out about 2-3.5V which would otherwise be wasted (next vid I will show this) Thanks for the positive comments
TheB3e 3 years ago
I'm not sure why it lasts for 2 days at this point, I know I am drawing only about 20miliamps with the proper commutator timing. I have added more wire to the main coil, aprox 500 more feet. The resistance has gone up but now draws even less from the battery. I did notice as you go with more windings in the coil, amperage goes down as long as the voltage is higher to keep the RPM's up.
I have measured A/C voltage spikes with the bigger coil at over 1000v!! Off the meter..
TheB3e 3 years ago
I have to make you a question... How many Amps you need to run the motor and how many amps can the generator put out?
Nonetub 3 years ago
The "motor" will actually spin slowly off of 1 AA battery 1.5V - so to answer your question, it will technically run off of what 1 AA will provide as far as amps..
I will be taking more measurements and will post up the results.
TheB3e 3 years ago
To properly answer the question you could build a circuit that's used only for measuring the REAL power consumption of your motor. I explain how to do it on one of Armakuni2000's clips.
Drevtoobe 3 years ago
Excellent work! Like Nonetub, I'm in the Bedini SSG mode right now but I started out with a Newman motor first. I'm using AA batteries to run my SSG so your project interest me alot.
Lidmotor 3 years ago
Great job TheB3e!!! You show in this video how a better design can put more output energy... You show here how easy is to make an overunity device. You can post how to replicate you experiment in our NERD forum. Now, I´m working in the same idea, but using the Bedini motor. I want to compare what experiment can put more output energy, Newman or Bedini? Look in my uploaded videos and see my video about Bedini Motor/Generator to get an idea.
Nonetub 3 years ago