Dynam E-Razor 2.4Ghz bind Tx Bind Procedure

[450erazor]

could someone please explain the the dip switches on the dynam erazor stock tx

[Blueray450]

@450erazor

go to mycoolheli and look at the review section for the eRazor review. It has all that there plus more

[Blueray450]

Folks go to mycoolheli and then click the reviews and go to the eRazor. Then find the rcgroups thread and that is the absolute best place to get these questions answered quickly. thx

[504GENUWINE]

When and how is the best time to use the 3d switch? And why is the throttle power different when you flip the switch?

[504GENUWINE]

I have an issue with my e razor 450. Everytime I get ready to give more throttle to it, it begins to spin around and I can't figure out how to keep it steady as other helicopters should. So can you help me fix this issue???

[yz426clint]

I bought a new Rx but still cant get collective pitch . i have t pro servos

[504GENUWINE]

What's the title and listing of the video? Because also, my helicopter is shaking really bad and spinning. So this is the reason why I need the help to know how fix the pitch and track the blades with this particular 2.4ghz transmitter with the all the DIP SWITCHES. So I wanna make sure which one's to use correctly? But also the 72mhz transmitter seams easier to use from a video I've seen by DAVIDSUNSHINE... But anyways can you help out with a simple video to make? I would really appreciate it

[504GENUWINE]

Its not on there as a video like this?

[504GENUWINE]

I also have a e razor 450. But can you please make a video on how to set the blade/pitch tracking with this type of transmitter? Because im having problems on trying to figure it out what to do, can you help me please? ??

[Blueray450]

@504GENUWINE

Adjust blades mechanically for 0 pitch at center stick with motor disconnected and on idle up.

[matrix49A]

I love the band-aids on this hand.

[Blueray450]

@matrix49A

HAHAHA, Just dry fingers cracking from all the heli work.

[504GENUWINE]

And mines aways spin to the right, so how do I fix that?

[504GENUWINE]

I have the same e razor 450. And also, can you make a video on showing how to properly adjust and correct the trims so that it can fly correctly???

[Blueray450]

@504GENUWINE

If you are a beginner, look at the beginner video training on MyCoolHeli

[yz426clint]

make a video on the gyro tune and setup

[malolos1962]

can anyone help me how trim my dyman erazor 450 first time i tried to fly it just keep hovering to backward left any sugestions. thanks

[chatch15117]

Would you mind opening up the Tx and take a picture of the PCB? There are 6 screws on the back. Just pop it open a little, disconnect the battery connector and then it will open. Nothing will fall out... everything is secured inside. I just need a picture of what it looks like when you open it up.

[EVELYNEMIL]

Hello, I bought my new E Razor 450 but I can not charge my battery with the suppied charger, nothing happens, any sugestion?. Thanks!!.

[cmartman48]

No luck meaning that I can't get it to beep like the video.

My ESC beeps in different sequences.

I watched two videos on the E-razor450 and both haqs the same beep sequence instructions.

I did toggle the gear switch but I will give it another try.

Can you explain to me about the low/high time programming. I dont have a clue!

THK U!

[cmartman48]

Why do you think my ESC on my e-razor 450 has a different beeping sequence?

I have the same 2.4 GHZ radio.I did the exact sequence in the manuel and video with no luck.

[Blueray450]

@cmartman48

No luck with what?

Did you toggle the gear switch? (top left?) There is a video on the xheli page that shows the new tx is a little different.

[captainLeeMunro]

Yes please cover the 10 switches on the bottom. I just got my today and I can't get to hover because it keeps pitching to the left. I've thief to trim it but it doesn't help.

[xTvSxLaZer]

Ok can you post a video on how to disconnect the ESC on a E-razor 450 please!

People are telling me to disconnect the ESC on any helicopter before you pitch it!

So with the model helicopter shown in this video. Can you please show us how to disconnect the ESC! thankyou!

[Blueray450]

@xTvSxLaZer

Disconnect 2 of the 3 wires going from the ESC to the Motor.

[xTvSxLaZer]

@Blueray450 Ok i dont that... but now my helicopter dosn't lift off the ground

[HappySCVResident]

Please cover the 10 switches below too sometime. I'm totally lost on where to position them.

[Blueray450]

@HappySCVResident

look at the razor 450 review page on mycool heli d ot com

[iBradapps]

@HappySCVResident I cant seem to find the switches info on the site... what is the correct way to put them?

[HappySCVResident]

Man I really wish you would have covered setting up those PIT, CCPM, PLT, and the others at the bottom of the TX. I have no idea where or how to set them.

[Blueray450]

@HappySCVResident

Look at the erazor review page on mycoolheli d o t com

[jcer93705]

So i saw how you powered up with the frame laying, isn't that is so wrong for the gyro? Shouldn't it be on the skid while gyro and binding settle down? I wont even do that with my 50 size align trex helicopter gyro setting will be total wack. Can this heli do that with razor 450?

[donfartist]

I have one of these transmitters but after binding to the receiver I am unable to control the throttle and servos. Any advice?

[psygn0sis]

@donfartist flip the MODE (left toggle switch) switch and then flip it back. It's a new safety switch.

[Prttimeninja2]

Meh.. TOoooooOoo Much work. I would die having to put up with this EVERY time.

[Blueray450]

@Prttimeninja2

Thats why Xheli made the effort to pull it from their Heli offering once they saw the vid. I don't know if Dynam has fixedt the problem yet.

[psygn0sis]

@Prttimeninja2 Pretty much the same start up procedure for every heli. Turn on Tx.. plug in battery... wait... done.

[Blueray450]

@psygn0sis

Nope, with Walkera and Dynam, you have to turn on Rx first. It binds each time you turn it on.

[djminich]

on every 6ch remote does the 3D switch always go down/away from you for regular flight mode?

[J444123]

Well i was using the 72 Mhz radio on my e-razor and the switch actually had to be switched the opposite way (pushing it forward meant 3D mode, and vice-versa)

[UnkleSi]

Great vid thanks. If I buy a better transmitter (Spektrum Dx6i) will it bind ok to the Erazor?

[Blueray450]

@UnkleSi

Not with the Dynam Rx. You will need a Spektrum Rx in it like an AR6100 which is fine for a 450.

[donfartist]

@Blueray450 I have one of these controllers. It binds ok but the servos and throttle wont work. Any advice?

[MaximD9]

#1 #1 #1 YES MAKE SURE THE 3D SWITCH IS IN THE OFF POSITION!!!!!! Bad things happin when its not trust me I found out first hand!! Hard lesson to learn but I wont be making that mistake again. Thnx for the vid!!