Corksport 80mm exhaust system on 2010 Mazdaspeed3 (Inside)

[chris24mil]

i would rather have the HMMWV in the background....lol



[PrivatePenis]

whats that small gauge on the left side of the dash do?

[D16Turbo86]

your car sounds nice! is that Ft. Polk? Ft. Polk = shit lol

[MangoSmoothie16]

whats wrong with the stock boost gauge?

[TheMaverickSpawn]

thank you for serving our country and thank you for the vid i am so getting that pod

[Cobaltridar]

What is the name of the boost gauge pod that you have?

[myttuf1]

@Cobaltridar I got it from a guy on mazdaspeedforums that makes them, his screen name on that website is: block8head.

[MrRizzlybear]

Yes all Speed 3s are...

[Fadeaway97]

Is ur car manual

[kendallanimal12]

K cool thanks for all the info. Have you checked out my ride yet?

[kendallanimal12]

where did you get you boost gage pod from? I am installing an Auto meter bost gage but I do not want to use a piller pod.

[myttuf1]

@kendallanimal12 I got it from a guy on mazdaspeedforums named "block8head"... He makes and sells them himself.

[kendallanimal12]

@myttuf1 How much dose he charge and would i fit my auto meter gage? I cant find a piller or pod anywher for are cars.

[myttuf1]

@kendallanimal12 I think it was around $80 shipped, and he makes different sizes to fit the common gauge sizes... Once you find him, private message him to make sure everything fits.

[V10ViperGTS]

I'm active duty military (25 years) and bought a MS3 to bring to Italy (6 months of fun so far) and have been looking at mod ideas for the car (I am a HP junky (check my videos)), so your videos have been helpful. I see that you got out of the service (one of your comments) so thanks for your service and hope you landed on your feet OK with a good job, etc. Take care, and again, thanks for the videos.

[myttuf1]

@V10ViperGTS Thank you, and thank you for your service as well.

[V10ViperGTS]

@myttuf1 Were any of the mods you installed difficult or are they pretty "cut and dry" and easy to install? With my being overseas, I still have access to a lift at the base, but if something goes wrong I do not have access to a tuner shop or dealership that can work on my car. They would simply say "This no Fiat".

[myttuf1]

@V10ViperGTS I was able to do every mod myself at the shop I had on base. However, I got a lot of my know-how and help from some Mazda online forums that I frequent: mazda3revolution and mazdaspeedforums... These websites are full of information and there are a lot of how-to's that take you through the step of different installs.

[V10ViperGTS]

@myttuf1 Thanks. I'm on both sites and will dig in to the DIY stuff.

Ordering my stuff today or tomorrow. Take care.

[SalVatioN2011]

how much boost are you pushing...

[myttuf1]

@SalVatioN2011 The stock 15psi for now... Still gotta get a HPFP to safely up the boost.

[hondalover301]

Yea corksports exhuadt have alil drone noise but I guess u can deal with it

[Buhnanah]

How many HPs on that car?

[dfrankenbach]

Just had a question for mytuff1,

I know you showed the video of reving up at a standstill. Is their significant drone or noise when you are cruising at about 3000rpm at about 120km/h? I had the CS exhaust on my 10 2.5L and it was so loud you could hear the car from a significant distance. I have the 10 speed now and want to put the CS exhaust on again but am worried it will be the same thing. I know the turbo will cause the system to be somewhat quieter as it does act as a type of silencer.

[dragonx828]

Hey I think i saw you before, were you at downtown Killeen? Btw how much did everything cost i was looking at a similar setup.

[myttuf1]

@dragonx828 No, I'm not in TX, I was in WA, but now I'm in CA... For just the things listed in my sig, it cost roughly $1000 (not installed).

[teamxtaci]

@dragonx828

Thats me not him....who and where are you?:)

[myttuf1]

To get a defrost vent pod, you need to get a hold of "blockh3ead" on M3F (mazda3forums)... He's also on MSF (mazdaspeedforums) under the name "Ghostspeed". He uses a stock vent, and molds a plastic cup to the vent... It looks very professional, and he can make it in different sizes for different sized gauges.

[6u66a]

where did u get the gauge pod from?? p.s sounds sick!!

[myttuf1]

To get a defrost vent pod, you need to get a hold of "blockh3ead" on M3F (mazda3forums)... He's also on MSF (mazdaspeedforums) under the name "Ghostspeed". He uses a stock vent, and molds a plastic cup to the vent... It looks very professional, and he can make it in different sizes for different sized gauges.

[myttuf1]

No extra vibrations, it's the same as the stock exhaust except noise and power.

[kbeau]

i was wondering if you felt alot of extra vibrations when you rev or get on it..

[teamxtaci]

What about the POD?

[myttuf1]

It's a Prosport gauge, you can find them on Prosport's webpage. It's 52mm and it's mechanical.

[weezyx3]

i need to now were u found the guage please

[myttuf1]

The only thing stock on the exhaust is the downpipe, the midpipe/racepipe is 80mm and catless, from CS, and everything after that is 80mm piping from CS as well.

[jamjam0221]

what part of the exhaust system is modded? just the catback? or the whole thing?