quit using stainless, or anything with chromium in it. professional hydrogen generation companies use nickel and iron for the electrodes. hence better generation, and no poisonous by products. A little studying, and minor research can lead to a much safer, and cleaner generator
you should make separate collection system for hidrogen and oxygen (positive and negative electrodes)
Else only one spark and it will explode.
If you try egnite gas at output of the tube fire will go throu tube (because it contain eplosive gas mix) to generator and gas in generator will explode.
I estimate amount of gas to break this construction is about 20 cm^3 if it will contain more - hmm...
I think using wire is very iniffective way because
1 during operation of the "device" electrode will be "eaten" by chemical reactions in water so thin wires will be destroyed very soon so you need MUTCH thicker
2 for increasing production of gases you should increase current. for increasing current with same voltage you should increase surface of elecrodes.
i think it is a ordinary water cooker. The wires are connected and the adapter so the wire gets hot when electrons rush from min to plus. the friction between the the wire and the electrons creates friction. so it gets hot. the water warms up evaporating. the litle room of air above the water is under pressured, air is puched out. just air! You didn't see it burn did ya.
will be smaller and spacing tighter with 3/32 or 4.2mm. I'm using (.32) welding wire can't wait to see it run. Yours produces at 4.5VDC, what will it put out at 12 VDC 20amps.
good clean design, for the generator, and well put together video. This is the design I have chosen to impliment. Im still in the choosing materials stage however.
But wait i have the plans and a video for a better generator. This is a work in progress and I will be doing all the video and post it in the next few days
Thanks, That sounds great I can hardly wait. I will be looking forward to it, as soon as you give us a parts list, I think? I will be right with you. Do you think the new one will produce more gas's? Thanks again I am gratful, peace
H2O???
Step1: walk to the kitchen
Step2: open the tap
Step3: enjoy your H2O!
11olaf11 1 month ago
quit using stainless, or anything with chromium in it. professional hydrogen generation companies use nickel and iron for the electrodes. hence better generation, and no poisonous by products. A little studying, and minor research can lead to a much safer, and cleaner generator
ymdeardorff1 1 month ago
you should have used copper or aluminum wire much better conductor s
shepnannie 1 month ago
h20 h20 h20 h20 h20 h20 h20 post this on 4 other videos and the next morning u touch water u mite grow a tail
rikki14100 2 months ago
thts an hho generator NOT a h20 generator
ppsjsh 6 months ago
this guy sounds like raymond
zenga2902 6 months ago
Electrolisis
darkstone243 1 year ago
you should make separate collection system for hidrogen and oxygen (positive and negative electrodes)
Else only one spark and it will explode.
If you try egnite gas at output of the tube fire will go throu tube (because it contain eplosive gas mix) to generator and gas in generator will explode.
I estimate amount of gas to break this construction is about 20 cm^3 if it will contain more - hmm...
you probably loose hand if will hold it at time
odv000 2 years ago
sorry for my english.
I think using wire is very iniffective way because
1 during operation of the "device" electrode will be "eaten" by chemical reactions in water so thin wires will be destroyed very soon so you need MUTCH thicker
2 for increasing production of gases you should increase current. for increasing current with same voltage you should increase surface of elecrodes.
I think plates much effective
and
NEVER MIX HYDROGEN AND OXYGEN IN SAME TANK
it can and will explode
odv000 2 years ago
4.5 volts isn't good. get like 1kv or something... low amps is good too. it won't heat the water up much.
harryfodder 2 years ago
great work
blackspider999 2 years ago
i dont think bakeing soda is any good i used koh
samking12 2 years ago
i think it is a ordinary water cooker. The wires are connected and the adapter so the wire gets hot when electrons rush from min to plus. the friction between the the wire and the electrons creates friction. so it gets hot. the water warms up evaporating. the litle room of air above the water is under pressured, air is puched out. just air! You didn't see it burn did ya.
whell thats what i think. no offence
sneakyjjb 3 years ago
Dude build one and light the bubbles but be careful as it can and will explode i found out the hard way trust me
katoosh1 3 years ago
Make money on YouTube: /watch?v=iHs1ScFVUnU
memernolly 3 years ago
@memernolly the video is privte dude
rcvideogamer 2 years ago
Outstanding, well done video, thank you!
Same type I'm building. The coil I'm planning
will be smaller and spacing tighter with 3/32 or 4.2mm. I'm using (.32) welding wire can't wait to see it run. Yours produces at 4.5VDC, what will it put out at 12 VDC 20amps.
MikPil 3 years ago
good clean design, for the generator, and well put together video. This is the design I have chosen to impliment. Im still in the choosing materials stage however.
katrinaro 3 years ago
But wait i have the plans and a video for a better generator. This is a work in progress and I will be doing all the video and post it in the next few days
h2oFuelTechnology 3 years ago
Thanks, That sounds great I can hardly wait. I will be looking forward to it, as soon as you give us a parts list, I think? I will be right with you. Do you think the new one will produce more gas's? Thanks again I am gratful, peace
waltsingletary 3 years ago
nice 1
nolelox 3 years ago
thanks chap very informative and easy to do. Lots better without the music :)
nolelox 3 years ago