K&N Cold Air Intake. if it doesn't already have it. also you should get a 2.1 Kenne Bell supercharger they are sick! if you go to the K&N site and pick out your car then they will guarantee a certain amount of horsepower. if you provide proof that it didnt at least give you that much horsepower then they send your money back but you keep the filter. also if the 2.1 kenne bell supercharger is pumped up the max psi i think its around 200 extra hp? dont quote me on that one though. nice car! :D
headers,underpullies ,Xpipe, 373 in the rearend ..and chip it after that i would look into intakes,throttle bodys ect ect....the dumbass below has no idea that u have to build a bottom end before going whipple or kb supercharger unless u wanna throw a rod threw the block ...even cobras have to build bottom ends after 5-9lbs of boost 03-04 cobras are a lil more tougher and direct bolt on but for a GT rebuild bottom end to take the abuse new rods and pistons on that 2v 4.6 or pay for it later
headers,underpullies ,Xpipe, 373 in the rearend ..and chip it after that i would look into intakes,throttle bodys ect ect....the dumbass below has no idea that u have to build a bottom end before going whipple or kb supercharger unless u wanna throw a rod threw the block ...even cobras have to build bottom ends after 5-9lbs of boost 03-04 cobras are a lil more tougher and direct bolt on but for a GT rebuild bottom end to take the abuse new rods and pistons on that 2v 4.6 or pay for it later
anybody know where i can buy the stinger mufflers? everywhere i look is a complete exhaust and i already have a complete exhaust i just wanna change the mufflers to the stingers
Dude, I've got the same car but I drive it to death. I have 160,000 miles on it and everything except brakes and tires are original. If yours is stock then you must add a CAI, but make sure you can get it in and out of the fender hole, mine is too wide. The BEST thing you can do cheap are underdrive pulleys. You will SHIT A BRICK at how much quicker the car is and it is only an hour swap. Next thing I do is cast iron lower end and a kenne-bell sc when I get the money
@maestas04gt Yes but it is a pain in the ass to drop the filter down through the wheel well when it has to be removed and cleaned. I'd cut the hole bigger but I want the body to remain stock.
@592220 Dude you can barely feel the difference of Under drive pullies and a CAI. I've got them both on my car and you will not feel a difference. They are both supporting mods. They only make a difference when other real HP mods are added.
gtet bbk shorty headers a bbk h pipe and flowmaster 2 chamber mufflers along with a k&n or bbk cold air intake and maybe a cam for some aggressive thumping
sorry for the extremely delayed response, for some reason youtube has stopped sending me alerts when I receive comments... it's the stock midpipe. I've thought about changing it but I'm afraid of creating an unbearable drone
@2003slvrgt Sound weak with the stock pipe. I've never known Borla Stingers to drone much, but if you are concerned about it get an aftermarket X-pipe with cats. It will be louder with much more roar, but no drone. IMO LT headers, an O/R X-pipe and Stingers is one of the best set ups for a Mustang.
I'd throw on a pair of MAC LT's, catted MAC Prochamber H-pipe and a K&N FIPK. You'll have the best sounding GT in your area, for sure. These are the mods i have on my '03 GT coupe and everywhere i go i get commented and complimented about the sound. Dont have any vids posted of her yet as i JUST recently purchased the car and it's cold as hell outside. Come next summer i'll have a vid of my car ready for yuh.
@mgrande11 Indeed they are. Mine about brought out the worst in me, lol. I had half a mind to just yank the motor from the car and put them on that way.
throw out the h and get an x..way more torque down low and balanced better up high plus the sound is better...click on my page and listen to 08 bullit donuts/drifting thats frpp stingers(borla) and o/r x
Um, what? I've never once heard anyone say an x will have more torque, the h will have more torque, the x will have a little more hp and top end, and to me sound better...
If you're saying that it will have a little more Horsepower in the top end, you're saying that it will have more Torque. You're contradicusting yourself, really.
Horsepower is calculated from Torque, and revolutions per minute..
Horsepower = Torque X Engine RPM / 5,252.
What he means is that an X pipe flows better. An X pipe is really better suited for higher RPM operation, due to the ability for a faster exhaust gas velocity, due to increased flow over an H pipe.
that would be my dad.... he had just had back surgery at the time. sorry. (if you listen closely you can hear my mom at the end saying "are you leaving... are you leaving... henry... henry...) the circus i used to live in is the reason i moved out haha
Don't get an o/r x pipe... sounds shitty! For sure go with an o/r h or catted x pipe either sounds great. Also a tint would look good cause of your added mustang decals
Sounds good, maybe a high flow X pipe. Or an off road X pipe if you want, and some 3.5" tips. That would bring the tone out more. I'd also say a lowering kit and aftermarket wheels. A light bar would look great too being a convertible.
I'm actually buying some springs with Christmas money. Which brand do you recommend? I just want something moderate and tasteful I don't really want the car scraping the ground. Merry Christmas!
Id' say the Eibach Pro-kit. I have the Eibach Sportlines on mine, but I really have to be careful everywhere I go. I think the Pro-kit would be great. Happy Holidays!!
Thanks for the reply. I am pretty sure the pipping is stock. The endpipe's final bend before it goes straight to the tips is right where my tires are.
Hey I have an 04 GT and I recently put on some used Stingers myself and I love the sound. I have the stock rims with 245 tires but my right endpipe is VERY close to my tires which will be a problem later when I mount wider wheels. Can you tell me whether your right end pipe is like that too so I can figure out if it is a factory problem or just a problem with mine?
Hey there, I went and looked and my right pipe does come closer to the wheel by about an inch and a half. BUT I think that the bend is far enough back so that the tire could never touch it. Does your cat back have the borla piping on it or did someone redo the piping since it's used? Keep in touch, i hope i can help you figure this out
Ok you will have plenty of clearance for aftermarket rims and wider tires i have a 10" rim and 275 all around on my 02 GT and have no problems. Next I would go with an off road X pipe, throttle body and plennum combo, and a cold air intake. I could give you a whole list but if you're really interested get a hold of me and I'll hook you up.
If you remove those back cats and add a K&N air filter your car will sound like a Nascar when you get on it...It will be frickin loud...lucky for me that is the way I wanted it...lol..By the way...dont spend the money on headers...for what they cost to install according to Ford Racing they are not worth it...Eric
sure is.....if you're gonna go all out you might as well save up for some LT headers....I just ordered Borla Stingers and a Bassani catted X, hoping to get some LTs here soon though. Good luck with the exhaust setup.
hey 2003slvrgt u should go with the H-pipe...like u said below it is better sounding than a x-pipe. anyways nice 'stang and i hope u will post sum more vid's of it
yeah thats my dad, he had gotten home from getting back surgery the same day i took this haha. He was milking it... trying to make the neighbors feel sorry for him haha
It sounds pretty good, would have sounded better with the revs above 2k but i know it was cold, have you changed the h-pipe yet or is it just a cat back.
nah i haven't changed it yet. ha i'm hoping to change it with my christmas money haha (but food comes first) i know some people like the x-pipes the best but i want to go for the h cause 1, its different and 2, i think the h carries a deeper note
me too! i'm actually thinking about looking into it myself. i think theres a few on youtube with that combo or maybe its streetfire DOT net. if i decide to do it i'll put one up :)
Sounds sick bro.
But I love how in the background before he starts the car,
That a man and a woman are talking about taking steroids. And the woman says, "yeah, those are good."
DerrickT113 9 months ago
K&N Cold Air Intake. if it doesn't already have it. also you should get a 2.1 Kenne Bell supercharger they are sick! if you go to the K&N site and pick out your car then they will guarantee a certain amount of horsepower. if you provide proof that it didnt at least give you that much horsepower then they send your money back but you keep the filter. also if the 2.1 kenne bell supercharger is pumped up the max psi i think its around 200 extra hp? dont quote me on that one though. nice car! :D
TheZohaun 1 year ago
headers,underpullies ,Xpipe, 373 in the rearend ..and chip it after that i would look into intakes,throttle bodys ect ect....the dumbass below has no idea that u have to build a bottom end before going whipple or kb supercharger unless u wanna throw a rod threw the block ...even cobras have to build bottom ends after 5-9lbs of boost 03-04 cobras are a lil more tougher and direct bolt on but for a GT rebuild bottom end to take the abuse new rods and pistons on that 2v 4.6 or pay for it later
MrSilent937 1 year ago
headers,underpullies ,Xpipe, 373 in the rearend ..and chip it after that i would look into intakes,throttle bodys ect ect....the dumbass below has no idea that u have to build a bottom end before going whipple or kb supercharger unless u wanna throw a rod threw the block ...even cobras have to build bottom ends after 5-9lbs of boost 03-04 cobras are a lil more tougher and direct bolt on but for a GT rebuild bottom end to take the abuse new rods and pistons on that 2v 4.6 or pay for it later
MrSilent937 1 year ago
anybody know where i can buy the stinger mufflers? everywhere i look is a complete exhaust and i already have a complete exhaust i just wanna change the mufflers to the stingers
cb250exrider 1 year ago
Dude, I've got the same car but I drive it to death. I have 160,000 miles on it and everything except brakes and tires are original. If yours is stock then you must add a CAI, but make sure you can get it in and out of the fender hole, mine is too wide. The BEST thing you can do cheap are underdrive pulleys. You will SHIT A BRICK at how much quicker the car is and it is only an hour swap. Next thing I do is cast iron lower end and a kenne-bell sc when I get the money
592220 1 year ago
@592220 well if the cai doesnt fit in the finder hole u have to install it through under the finder thats what i had to do.
maestas04gt 1 year ago
@maestas04gt Yes but it is a pain in the ass to drop the filter down through the wheel well when it has to be removed and cleaned. I'd cut the hole bigger but I want the body to remain stock.
592220 1 year ago
@592220 Dude you can barely feel the difference of Under drive pullies and a CAI. I've got them both on my car and you will not feel a difference. They are both supporting mods. They only make a difference when other real HP mods are added.
Neckbonekat1029 1 year ago
oh ight brooo
cubanpimp727 1 year ago
throw 410's in that bitch!
blnts0722 1 year ago
gtet bbk shorty headers a bbk h pipe and flowmaster 2 chamber mufflers along with a k&n or bbk cold air intake and maybe a cam for some aggressive thumping
rp94cobra 1 year ago
Hey what midpipe you running?
Scubajarrett 1 year ago
sorry for the extremely delayed response, for some reason youtube has stopped sending me alerts when I receive comments... it's the stock midpipe. I've thought about changing it but I'm afraid of creating an unbearable drone
2003slvrgt 1 year ago
@2003slvrgt Sound weak with the stock pipe. I've never known Borla Stingers to drone much, but if you are concerned about it get an aftermarket X-pipe with cats. It will be louder with much more roar, but no drone. IMO LT headers, an O/R X-pipe and Stingers is one of the best set ups for a Mustang.
Neckbonekat1029 1 year ago
nice ride man
cubanpimp727 2 years ago
thanks pimp.... haha sorry I couldn't resist
2003slvrgt 1 year ago
I'd throw on a pair of MAC LT's, catted MAC Prochamber H-pipe and a K&N FIPK. You'll have the best sounding GT in your area, for sure. These are the mods i have on my '03 GT coupe and everywhere i go i get commented and complimented about the sound. Dont have any vids posted of her yet as i JUST recently purchased the car and it's cold as hell outside. Come next summer i'll have a vid of my car ready for yuh.
CBRuRedE 2 years ago
LT's are a pain in the ass to install on the new edge stangs
mgrande11 1 year ago
@mgrande11 Indeed they are. Mine about brought out the worst in me, lol. I had half a mind to just yank the motor from the car and put them on that way.
CBRuRedE 1 year ago
throw out the h and get an x..way more torque down low and balanced better up high plus the sound is better...click on my page and listen to 08 bullit donuts/drifting thats frpp stingers(borla) and o/r x
dalemllns 2 years ago
Um, what? I've never once heard anyone say an x will have more torque, the h will have more torque, the x will have a little more hp and top end, and to me sound better...
papaown 2 years ago
If you're saying that it will have a little more Horsepower in the top end, you're saying that it will have more Torque. You're contradicusting yourself, really.
Horsepower is calculated from Torque, and revolutions per minute..
Horsepower = Torque X Engine RPM / 5,252.
What he means is that an X pipe flows better. An X pipe is really better suited for higher RPM operation, due to the ability for a faster exhaust gas velocity, due to increased flow over an H pipe.
kcole939 1 year ago
Whoa, typo. Somehow I hit a 'u' and an 's' in the word contradicting. Haha, oh well.
kcole939 1 year ago
Long tube headers and K&N intake...
ho0dbridge4lyf87 2 years ago
who the fuck is talking about steroids?
cfilose07 2 years ago
that would be my dad.... he had just had back surgery at the time. sorry. (if you listen closely you can hear my mom at the end saying "are you leaving... are you leaving... henry... henry...) the circus i used to live in is the reason i moved out haha
2003slvrgt 2 years ago
kenne bell supercharger :)
buxton11 2 years ago 2
no supercharger there budd
rocky440 2 years ago
he was asking for future mods
buxton11 2 years ago
lol sorry, i see that now. but yeah, that'd be sweet,
rocky440 2 years ago
either smoked tailights or a rear blackout panel
stuntrider15 2 years ago
mac prochambers are good check out my vid.........03 gt mac prochamber no cats
gtracer56 2 years ago
dude lower an inch and a half and open up the exhaust more, she sounds restricted
smc13s 2 years ago
Don't get an o/r x pipe... sounds shitty! For sure go with an o/r h or catted x pipe either sounds great. Also a tint would look good cause of your added mustang decals
warriorfan514 2 years ago
the o/r h pipe is the best lol i agree
coolguy3432 2 years ago
bassani catted x pipe next man, trust me
hastings631 2 years ago 2
sounds really nice
PortalRealm 2 years ago
sell it....buy an 03/04 cobra :)
boostedassasins 3 years ago
EXACTLY!!! to bad they can up to twice the price tho haha
speeddemon0712 2 years ago
lol
boostedassasins 2 years ago
Sounds good, maybe a high flow X pipe. Or an off road X pipe if you want, and some 3.5" tips. That would bring the tone out more. I'd also say a lowering kit and aftermarket wheels. A light bar would look great too being a convertible.
josephsvt 3 years ago
I'm actually buying some springs with Christmas money. Which brand do you recommend? I just want something moderate and tasteful I don't really want the car scraping the ground. Merry Christmas!
2003slvrgt 3 years ago
Id' say the Eibach Pro-kit. I have the Eibach Sportlines on mine, but I really have to be careful everywhere I go. I think the Pro-kit would be great. Happy Holidays!!
josephsvt 3 years ago
I heard that new shocks and struts are required after installing lowering springs. Is this true?
warriorfan514 2 years ago
Thanks for the reply. I am pretty sure the pipping is stock. The endpipe's final bend before it goes straight to the tips is right where my tires are.
StriderTacticaL 3 years ago
I meant the piping is original borla
StriderTacticaL 3 years ago
Hey I have an 04 GT and I recently put on some used Stingers myself and I love the sound. I have the stock rims with 245 tires but my right endpipe is VERY close to my tires which will be a problem later when I mount wider wheels. Can you tell me whether your right end pipe is like that too so I can figure out if it is a factory problem or just a problem with mine?
Thanks
StriderTacticaL 3 years ago
Hey there, I went and looked and my right pipe does come closer to the wheel by about an inch and a half. BUT I think that the bend is far enough back so that the tire could never touch it. Does your cat back have the borla piping on it or did someone redo the piping since it's used? Keep in touch, i hope i can help you figure this out
2003slvrgt 3 years ago
Ok you will have plenty of clearance for aftermarket rims and wider tires i have a 10" rim and 275 all around on my 02 GT and have no problems. Next I would go with an off road X pipe, throttle body and plennum combo, and a cold air intake. I could give you a whole list but if you're really interested get a hold of me and I'll hook you up.
lcplidk 3 years ago
headers, x-pipe
tdv1985 3 years ago
If you remove those back cats and add a K&N air filter your car will sound like a Nascar when you get on it...It will be frickin loud...lucky for me that is the way I wanted it...lol..By the way...dont spend the money on headers...for what they cost to install according to Ford Racing they are not worth it...Eric
cirellsky 3 years ago
get a hardtop. lol i dont know why i just aam not fond of any type of convertable....... sounds soo nice tho
snowxracer12 3 years ago
get some wider rear wheels, that adds to the add ass look
Hellz420 3 years ago
slap a Bassani O/R X pipe on it....man that'll scream
CDStang 3 years ago
that's what i've been saving up for, bassani is expensive, but worth the money
2003slvrgt 3 years ago
sure is.....if you're gonna go all out you might as well save up for some LT headers....I just ordered Borla Stingers and a Bassani catted X, hoping to get some LTs here soon though. Good luck with the exhaust setup.
CDStang 3 years ago
Borla and Magnaflow are the 2 best sounding exhausts...nice sound man
dhk07 3 years ago
thank you
2003slvrgt 3 years ago
WOW That sounds amazing!!!! Blows Flow Masters out of the water.
ilovesilvia69 3 years ago
hey 2003slvrgt u should go with the H-pipe...like u said below it is better sounding than a x-pipe. anyways nice 'stang and i hope u will post sum more vid's of it
1967bullitt 3 years ago
i swear i hear someone talking about taking steroids before you get in the car.. no chit.
ronniej1183 4 years ago
LOL, I hear the same thing too. A man and a woman are talking about them.
gobucks10304 4 years ago
yeah thats my dad, he had gotten home from getting back surgery the same day i took this haha. He was milking it... trying to make the neighbors feel sorry for him haha
2003slvrgt 4 years ago
It sounds pretty good, would have sounded better with the revs above 2k but i know it was cold, have you changed the h-pipe yet or is it just a cat back.
abrianL 4 years ago
nah i haven't changed it yet. ha i'm hoping to change it with my christmas money haha (but food comes first) i know some people like the x-pipes the best but i want to go for the h cause 1, its different and 2, i think the h carries a deeper note
2003slvrgt 4 years ago
no offense man, but it could use better and louder mufflers.........
390851 4 years ago
there arent that many mufflers that are better than borka stingers and they are pretty loud.
WAsoccer24 4 years ago
theres bassani, v-force and others..........
390851 4 years ago
Im curious about a Mac O/R H prochamber and borla stinger combo
grasshopper0223 4 years ago
me too! i'm actually thinking about looking into it myself. i think theres a few on youtube with that combo or maybe its streetfire DOT net. if i decide to do it i'll put one up :)
2003slvrgt 4 years ago