so i have an sr5 hatch, ive got a gts rear end and full coilovers i can put on it and i know a place that sells 1uzfe's for 700 bucks, and i got to thinking... put one in the corolla???? but i need custom mounting brakets and trans crossmembers, you guys wouldent happen to make them would you?
@xXPanfy004013Xx Don't use GTS rear end, it won't hold up, use ford rear end. 9" is best, but you can use 7.5 and 8.8" too. They're all cheap but you could take 2 ford explorer rear ends, since their differential is offset to the passenger side, use the short passenger side axle from each and make a centered, shorter version of the two, suitable length for ae86, then you saved $150 for shortening each axle, which could be used to make it 4 nuts, and caliper mounting brackets :)
@terribleoneprimopro Don't know what you are talking about, unless it is just the lack of exhaust. The engine sounds great if you watch the videos of this car with exhaust.
@corollafrenzy you know whats a great replacement for the 4AG....2RZFE out of the tacoma its finally coming into its own and paradise racing has started a movement for it...its capable of putting down more hp then the 2JZ
excellent! i'm about to do the same swap and could use all the help you could give. right now wondering about unecessary wiring on the engine harness but also the basic install in the small engine bay!
OK, Tnx, have you got any info on what wires need to be connected as I have just put the same engine in a Toyota Hilux, so no doubt will have the same 'challenges' that you had!
That's a cool swap! I have a w58 in my MKIII supra that I won't be using cos I'm swapping a 2jz into it. How did you get the W58 to mate up to the 1UZ-FE? I heard they only had an auto tranny. did it only involve getting a different bellousing or something? Thanks!
so i have an sr5 hatch, ive got a gts rear end and full coilovers i can put on it and i know a place that sells 1uzfe's for 700 bucks, and i got to thinking... put one in the corolla???? but i need custom mounting brakets and trans crossmembers, you guys wouldent happen to make them would you?
xXPanfy004013Xx 1 month ago in playlist More videos from ck1uzfeae86
@xXPanfy004013Xx Don't use GTS rear end, it won't hold up, use ford rear end. 9" is best, but you can use 7.5 and 8.8" too. They're all cheap but you could take 2 ford explorer rear ends, since their differential is offset to the passenger side, use the short passenger side axle from each and make a centered, shorter version of the two, suitable length for ae86, then you saved $150 for shortening each axle, which could be used to make it 4 nuts, and caliper mounting brackets :)
yubastardus 1 month ago
sounds like p00p. revs kinda slow too.
FLNative1 4 months ago
I'm curious...corner weight ?
123cameltosis 11 months ago
Man that car still sounds like heaven.
aShoe0o 1 year ago
Dam that box is tighter then a virgin o.O
RIllCHY 1 year ago
Do you still an AC with that setup?
aShoe0o 1 year ago
@aShoe0o
No sir, currently has no AC. It could be retained with a little work though.
ck1uzfeae86 1 year ago
it fits fine? no need to cut the firewall?
mattforce400 1 year ago
@mattforce400 Yup, fits just fine with no cutting. Just needed to lower the subframe a little bit.
ck1uzfeae86 1 year ago
wtf is that nasty ticking?
terribleoneprimopro 1 year ago
@terribleoneprimopro Don't know what you are talking about, unless it is just the lack of exhaust. The engine sounds great if you watch the videos of this car with exhaust.
ck1uzfeae86 1 year ago
So sick!! I picked up a smashed 93 sc400 and gunna do the same to my coupe cause the good ol 4ag aint cuttin it anymore.
corollafrenzy 2 years ago
@corollafrenzy you know whats a great replacement for the 4AG....2RZFE out of the tacoma its finally coming into its own and paradise racing has started a movement for it...its capable of putting down more hp then the 2JZ
Muzicsallitsworth 1 year ago
excellent! i'm about to do the same swap and could use all the help you could give. right now wondering about unecessary wiring on the engine harness but also the basic install in the small engine bay!
Axxel32 2 years ago
sweet as bro
brind0g 2 years ago
OK, Tnx, have you got any info on what wires need to be connected as I have just put the same engine in a Toyota Hilux, so no doubt will have the same 'challenges' that you had!
Cheers
uksupertrucks 2 years ago
Hi, great sound. What ECU did you use?
uksupertrucks 2 years ago
Stock LS400
ck1uzfeae86 2 years ago
WHAT MOTOR IS THAT FROM????\
fullymental307 2 years ago
1uz-fe from a 91 Lexus LS400
ck1uzfeae86 2 years ago
was the swap hard to do? could you email me a list of what had to be done to do this? thanks. nice car btw.
ok333 2 years ago
That's a cool swap! I have a w58 in my MKIII supra that I won't be using cos I'm swapping a 2jz into it. How did you get the W58 to mate up to the 1UZ-FE? I heard they only had an auto tranny. did it only involve getting a different bellousing or something? Thanks!
Tevolo52 3 years ago
That is true about only coming with automatics. I used a bellhousing made by A1turbos in New Zealand.
ck1uzfeae86 3 years ago
solid motor mounts?
Ill06Taco 3 years ago
Yes.
ck1uzfeae86 3 years ago