This morning I flew the wing dragon for the first time. It flew very strangely it kept wanting to fly down and without any elevator it went down fast not straight down but very fast and at an angle Why do you think that it is flying like this? I did not position the motor as you did. I used two plywood sections and then the back of the plane I just made that piece longer so the motor sat up higher. However, it was very similar to what you did. Please help
I used the two 1 x 4 x 1000mm carbon fiber strip. You could also use a CF tube, however I prefer the CF strip since it will lay flush against the wing joiner.
Thank you very much for helping me with all off the problems you have been a huge help to get my wing dragon to fly. although not yet maiden flight with brushless but again huge help thanks a lot.
what do you recomend as the best wd combo with brushless and lipo and what motor, wing, tail assm, and what do you thing the best combo is there to be flown. what wing would you say from the wd 4 wd 3 or begin air
I recommend the TowerPro 2408-21T-3A with an 18 Amp Brushless ESC. I am using a 3 cell 1320 mAh Lipo battery. Several people have used this combination with very good results.
I forgot, I recommend the WD4 wing and tail assembly. I find that it glides much better with the WD 4 setup. It also looks much cooler in the air. You will need two micro servos and a Y connector.
I would just like to say that you are just so good at flying the wing dragon and all the mods you do. I have a wing dragon and after seeing everything you did on it I ordered the motor that you recomended and I am going to put it on my plane.
The WD 3 wing has too much dihedral. I recommend going with the WD4 wing and tail assembly. The WD 4 wing is more aerodynamic and has better glide characteristics.
This morning I flew the wing dragon for the first time. It flew very strangely it kept wanting to fly down and without any elevator it went down fast not straight down but very fast and at an angle Why do you think that it is flying like this? I did not position the motor as you did. I used two plywood sections and then the back of the plane I just made that piece longer so the motor sat up higher. However, it was very similar to what you did. Please help
skullcrusher491 4 years ago
Sorry to bother you again but what dimensions of carbon fiber did you use to reinforce your wing?
skullcrusher491 4 years ago
I used the two 1 x 4 x 1000mm carbon fiber strip. You could also use a CF tube, however I prefer the CF strip since it will lay flush against the wing joiner.
BosTom123 4 years ago
When you mounted the gws prop was the writing facing the motor or the tail?
Thanks
skullcrusher491 4 years ago
Writing on the prop should always face forward. If the airflow is reversed then invert the connection of two of the three wires to the motor.
Tom
BosTom123 4 years ago
Thank you very much for helping me with all off the problems you have been a huge help to get my wing dragon to fly. although not yet maiden flight with brushless but again huge help thanks a lot.
skullcrusher491 4 years ago
This has been flagged as spam show
You are welcome. Let me know if you have any further questions.
Tom
BosTom123 4 years ago
what do you recomend as the best wd combo with brushless and lipo and what motor, wing, tail assm, and what do you thing the best combo is there to be flown. what wing would you say from the wd 4 wd 3 or begin air
skullcrusher491 4 years ago
I recommend the TowerPro 2408-21T-3A with an 18 Amp Brushless ESC. I am using a 3 cell 1320 mAh Lipo battery. Several people have used this combination with very good results.
Tom
BosTom123 4 years ago
I forgot, I recommend the WD4 wing and tail assembly. I find that it glides much better with the WD 4 setup. It also looks much cooler in the air. You will need two micro servos and a Y connector.
Tom
BosTom123 4 years ago
what is with the comments
moehawkkid 4 years ago
I still see all your comments. They are all there.
Tom
BosTom123 4 years ago
Sorry about all of that I could not see any of them.
skullcrusher491 4 years ago
No problem. It also took me a while to figure out YouTube's message posting system.
Tom
BosTom123 4 years ago
hey why did you delete
skullcrusher491 4 years ago
hey why did you take my comment off?
skullcrusher491 4 years ago
I would just like to say that you are just so good at flying the wing dragon and all the mods you do. I have a wing dragon and after seeing everything you did on it I ordered the motor that you recomended and I am going to put it on my plane.
skullcrusher491 4 years ago
For the upgrade I recommend checking my "EingDragon - Upgrade to Brushless" discussion thread on RCGroups.
Tom
BosTom123 4 years ago
I read all of that and went to see your vids. also do you thing I should make my wd 3 to a 4 or just make aelerons
skullcrusher491 4 years ago
The WD 3 wing has too much dihedral. I recommend going with the WD4 wing and tail assembly. The WD 4 wing is more aerodynamic and has better glide characteristics.
Tom
BosTom123 4 years ago