SOMETHING NEW FOR HHO FUEL CELLS.

[Javadavida]

I have found that if the cell design heats up the water too much you're wasting energy with a design problem. The goal is to make HHO gas, not heat.

[jocell202]

Nice, you gota check out my save money on fuel with one wire vid out.

[Hollywoods7]

powerstream sells it

[HaveHandsOpen]

I use 2.2v to 2.4v 40A out, 12v at 7A to 8A in bin doing it for over 2 years now.

I use SIL40C-12SADJ-VJ DC/DC Converters & Regulators 10.2-13.8Vin 40A

[1forgotten]

Hi Great video , Where is converter brought from? ANY LEADS WOULD BE GREAT

THANKS

[budabob07]

10,000th view :)

[thesquater137]

Hey if I have a 32 plate pos neg setup will I run into any water vapor problems ?

[tattoostudio666]

Hi there! :]

Im converting now my bmw 7 with same Converter...could you look at it in free time-meabye you find something I missed, please?

youtube.com/watch?v=Z5hCGC_I82­A

Any Comment or Suggestion are welcome (part 1 is open for Comments).

Regards!

[Hollywoods7]

YOU CAN GET IT FROM POWER STREAM,YOU NEED TO REDUCE THE PLATE VOLTAGE DOWN TO 2 VOLTS ,INTEAD OF 3 AND 4 VOLTS FROM FACTORY.THAT WOULD BE A MOD TO THE CONVERTER.

[n714x]

@Hollywoods7 What is the make and model number for the converter please

[amos033]

@Hollywoods7 Nice job. Were you able to get the mod to the converter to allow it to get down to 2 volts?

[mirox3mbg]

Where can I buy it from?

[waterwart]

ya it's great production...but is it getting hot?

[Hollywoods7]

@waterwart It is the 4 volts at the plate gap, which I already have a new converter from tggas which will have a lower and adj voltage for the gaps.

[Hollywoods7]

@Hollywoods7 what ever happen to tggas.

[Hollywoods7]

@waterwart Well you know if somethig gets hot there are ways to cool it.I did not get there yet.

[waterwart]

what about maybe using a 12 volt d/c to a 120 volts a/c power inverter and then plug in a 120 volt computer power converter which has a 12 volt power out at a set amperage????

[Hollywoods7]

@waterwart Also the new converter is a 120 v or 220 v converter I will let you know when I get it running.

[waterwart]

Hi. Would a 12 volt d/c to 120 a/c inverter work just as well and with a pwm to pulse the system????

[H2Truckers]

I found this12v input DC-DC ATX power supply and it looks like it might work on a 5.5v for a cell setup like this -n+n-n+n-n+n- and so on at 20amps.

Good luck with yours.

[Hollywoods7]

@H2Truckers LET ME KNOW HOW IT WORKS OUT I AM TRYN A NEW CONVERTER THAT WILL ALLOW UP TO 630 WATTS NOT 130 LIMITED ON THE POWER STEAM....................

[merlinspower]

I use the same system, the convertor I bought last year. It saves me auto battery, and alternator upgrades.. I have the Drycell, but like my Stanley Meyer tube cells the best

[Hollywoods7]

@supercell9 I FOUND ,THAT I THINK THE PLATE VOLTAGE IS SET TO HIGH FOR THE CONVERTER,3.5 TO 4 VOLTS IS COOKING THE WATER. IT STARTS TO CREATE A CONDENSATION TRAIL AS SOON AS I START IT UP. MY CELL WOULD TAKE 1 HOUR TO START A TRAIL .I AM GOING TO TRY TTSGAS PWM IT IS ADJUSTABLE FROM 1.5 AND UP.

[KENNNUSA]

@supercell9 actually it is made by PowerStream. I ordered mine from them not you. Do you own PowerStream? It says on ebay that you have only sold 2 though you claim to have sold hundreds. Problem I had is that the voltage cannot be adjusted and the current is only adjustable from 28-32 amps. Also it would not run my cells with neutral plates.

[H2Truckers]

I hope that ES2008 don't see this becouse he will call it a lie and a scam.

Good job Hollywoods7 keep up the good work ( Do you know if there is a 6v dc-dc out there )

[KENNNUSA]

@H2Truckers you can adjust the one from ttsqas from 1.5V to 24V. It is has a buck and boost converter built in and a pwm. You can also pulse the output or have it straight dc. I haven't seen anything that even comes close to touching it as far as options in power your cell.

[KENNNUSA]

meant to say powering your cell

[Hollywoods7]

@myhydrogencar I SENT YOU A PRIVATE MESSAGE HOPE YOU GOT IT .

[KENNNUSA]

Hey man, this is nice but the pwm I just ordered from ttsqas allows me to adjust the output voltage down to 1.5V even at high current. I don't have a oscilliscope so I like the fact that I can use my dmm to see what frequency, duty cycle, and current I am operating at. I think that I'd prefer his pwm because I'll have everyting for adjustment and measurement in one unit. Heat has been an issue with me and I did not want to have to add a water pump and resevoir.

[BlackDogSociety]

Where did you get the converter unit? And how water did you mix with the 1/4 TSP KOH?

Thanks for posting this vid...

[Hollywoods7]

@BlackDogSociety DISTILLED WATER AND THAT MEASUREING SPOON YOU SEE IN THE VIDEO REALLY IT WAS LESS THAN A 1/4 TSP BEACUSE THE KOH FLAKES WERE PRETTY BIG I WOULD HAVE TO CRUSH THEM UP TO FIT IN THE SPOON,I AM SELLIG THEM.I AM A DEALER.I AM WORKING ON THE PRICE WITH THE DEALER IN THE LOW 200S. BUT YOU NEED A CELL THAT IS +-+-+- ECT,12 AMP DRAW FROM SUPPLY AND 4 VOLT AT CELL=48 WATTS I GUESS THAT IS THE WAY YOU FIGURE IT OUT. HOPE THIS HELPS.DOMINIC.

[Hollywoods7]

@BlackDogSociety I SENT YOU A REPLY.HOPE IT HELPED.............

[BlackDogSociety]

@Hollywoods7 --- Well not really, how much KOH to how much water? Is it 1/4 TSP to 1 litter of water? I also looked up this converter and think it uses a buck converter circuit. It seems like this will work.

[Hollywoods7]

i am not ready for the new convetret test yet i have to build a cell,the other cell with the netural plates does 3 lpm at 30 amps x13.6 =408 watts i want to build a sprial wound cell or a bunch of tubes like the joe cell but set them up like pos and neg. he uses neturals,thats the way to get the dc to dc converter to work.remember the converter only works with +-+-+-,hope this helps.

[H2Truckers]

@Hollywoods7 Will it work with +n- tube cell? or just a dry-cell that is +n-n+n-n+n-.

[H2Truckers]

@H2Truckers oops I ment at 6v -n+ tube cell or dry-cell.

[H2Truckers]

This is just like what I have ben looking at.

Good job.

[H2Truckers]

@H2Truckers Can we say ( OVERUNITY )

[overunitydotcom]

How many Watts do you use to produce 3 Liters per Minute ?

4 Volts x how many amps ?

Many thanks.

Regards, Stefan.

[Hollywoods7]

@overunitydotcom 408 watts

[Hollywoods7]

@overunitydotcom 12 amps x4 volts 48 watts wow.

[hanker8860]

@Hollywoods7 your are using 4V x 30A = 120 W

[Hollywoods7]

@hanker8860 4V X 12 48 WATTS THE CELL IS AT 4 V AND THE DRAW AT THE CAR IS 12 AMPS,I GUESS THAT IS THE WAY.

[mrnewagemotor]

Zero fossil fuel would be pissed if he seen this one. He is putting alot into those current limiters he's building, you know ? But it was there all the time. It's a DC to DC converter right ? Now try a variable frequency drive too - they already make those too. It could help tune the cell - like a radio antenna .

[Hollywoods7]

@mrnewagemotor YEAH I WANTED TO DO THAT BEACUSE WATER WILL RESONANT AT 985 HERTZ,THAT MIGHT HELP A LITTLE,THANKS.

[rclewis01]

@Hollywoods7 I don't know for sure, but I would think that water would resonate at different frequencies based on temperature, impurities, and water level. If you had a microprocessor circuit like an Arduino, you could send a pulse every few seconds and listen for the ringing effect. Seek the maximum ringback and use that frequency. Just an idea.

[KENNNUSA]

@mrnewagemotor Yeah I bought Zero's but the frequency kept changing when I changed duty cycle and vice versa. I bought one of ttsqas's first ones early last year but I still had a issue with heat though the current was constant. I just ordered his new one which output voltage is adjustable down to 1.5 volts. Before I had to borrow a friends scop but his new one has jacks for dmm so you can see your frequency, duty cycle, and current in millivolts.