what should i get for my e maxx 9xl or 580 be doing bashing and speed runs. i want a motor with good tourque and a good top end, also which motor runs cooler?
where can i get one of these motors? could i mount it on the e-revo? and how? what ESC would i need? and would 8.4v 5000mah nimh packs be sufficient? what sort of speed could i expect?
The diffs held up well through the couple of hard runs on site here and while RC Car Action had the truck. The diffs were stock Savage units as I believe you guessed. I can only attribute this to adjusting the slipper properly and using the HD slipper spring on the KD web site.
Yes. I might have been a little past half throttle. I've used the Castle 2200 kV motor and the Fiegao 580L motor in 1/6 scale electric trucks and the Fiegao always comes out on top.
man looked like it was just warming up as it went past that was hauling
itchyundies 6 months ago
what should i get for my e maxx 9xl or 580 be doing bashing and speed runs. i want a motor with good tourque and a good top end, also which motor runs cooler?
0RobotWarsIsTheBest0 8 months ago
@0RobotWarsIsTheBest0
That depends. Will you want to run 4S, 6S LiPo or NiMH? And how much of a budget do you have set aside for the system?
milemarkers 8 months ago
@milemarkers no worries, i have a caslte 1717 on the way!
MonsterTruckMan316 5 months ago
the 580 are good motors!
brushless55 2 years ago
where can i get one of these motors? could i mount it on the e-revo? and how? what ESC would i need? and would 8.4v 5000mah nimh packs be sufficient? what sort of speed could i expect?
ESSOv8 2 years ago
whats your max speed on that?
veggie106 2 years ago
I never took the time to tune the aerodynamics on the truck shown, but a customer with the same system clocked one on radar at 71 mph.
milemarkers 2 years ago
how are the diffs holding up?
fathead431 2 years ago
The diffs held up well through the couple of hard runs on site here and while RC Car Action had the truck. The diffs were stock Savage units as I believe you guessed. I can only attribute this to adjusting the slipper properly and using the HD slipper spring on the KD web site.
milemarkers 2 years ago
is that lipo any good? is seems cheaper than any other lipo out there.
plorwax 2 years ago
Yes. I've sold hundred on the months the packs have been available and have heard of ZERO reported failures.
Dan
milemarkers 2 years ago
Hi Dan, if i put this motor in my brushless revo what speeds do you think i could get with motor temps below say 140 farenheit? thanks
Luke
shittybill93 2 years ago
wow so your saying that this motor is more powerful than the motor that comes with castle creations 2200kv one??? that was half throttle? seriously?
jocktheglide 2 years ago
Yes. I might have been a little past half throttle. I've used the Castle 2200 kV motor and the Fiegao 580L motor in 1/6 scale electric trucks and the Fiegao always comes out on top.
milemarkers 2 years ago
imagine that hitting you leg....
madcat303 2 years ago
The mamba monster can handle the power of that motor without over heat or toast result after a while ???
Joziebee 2 years ago
Simply put, yes.
Dan
milemarkers 2 years ago
Nice one mate but got to be honest that sounded like it was at nearly full throttle if not full throttle lol,5*
startazz 2 years ago
Oh, take my word. After trying about a half dozen times to max out the E-maxx, I never got close to full throttle.
Dan
milemarkers 2 years ago
Ok mate i'll take your word for it then LOL,keep them coming ok
startazz 2 years ago