I got mine $200 the other day and tried it out like 5 mins ago, i managed to break it and when i was holding it it randomly turned on so i have a swollen and bruised chin.. :(
Hey just wondering if this is a good helicopter, i am just about to buy one australian dollars cost $300 can anyone get it cheaper for me or can tell me this is good to buy.
Please give me an answer about how good this helicopter is.
Just a quick note. Since this video I got the bottle to engage the 3D switch and it really improves vertical stability. No more bobbing up and down. I guess I must have got the throttle curve or pitch curves wrong so I am at wrong rpm for stable hover.
Yer that's a point. When you plug the battery to the helli yo need to leave it stood still until the gyro led is constant red. you will also hear the servos jump into position. Only then can you pick it p and move it to the take off position better still connect up in the area you are going to take off from. I think that this function is to orientate the gyro to its settling position.
yes but you should be able to compensate with the sticks, or by adjusting the servo distance. if its second hand it could be the gyro is bust or the belt is on the wrong way, or even the rudder blades fitted the wrong way. this would make it snap into a spin.
Dude i had the same problem right. so i read the intructions and it says do not turn on the Transmiter [remote], so i didnt [i can hear the gyro started making wierd sounds and such, then after it was finished, the blinking light on the gyro was constant Red. But BECAREFULL!! During the gyro stage thing[ where its testing its functions] It tests everything, and i mean The over drive switch for 3D Stunts. so what you should do is put sumthing very heavy on the landing gear stuff.
cause i wasent aware tht when the remote was turned off it would test everything. when i did it it almost broke one of my blades but thank god it was carbon fiber lol
hi i have one of these, my first 6ch. but it really un stable , just drif to one side as it leaves the ground. even after treaming. is me not a good pilot or the heli has some problems. thanks
it could be jeclone already posted the answer. Try getting off the ground a bit higher to remove the effect of the rotor wash. Also start in a hall to eliminate any breeze and that way you will know if your settings are good or the conditions are bad. Good luck.
Yep its not too hard to fly at all. The best bit is it aint expensive to repair. I would recomand a couple of main shafts and a few landing skids extra. Also try to fly in no wind or sports hall. I cant compare to anything on the market today cos I havent flown hellis for about 20 years and that was on a fixed pitch so this one seems real easy.
Why??????????????We dont need this Video on youtube
Brokenwingking 1 month ago
you can get them for around $200-$300 AUS
CNCman200 2 months ago
I got mine $200 the other day and tried it out like 5 mins ago, i managed to break it and when i was holding it it randomly turned on so i have a swollen and bruised chin.. :(
ChloeTheAwesome 1 year ago
Hey just wondering if this is a good helicopter, i am just about to buy one australian dollars cost $300 can anyone get it cheaper for me or can tell me this is good to buy.
Please give me an answer about how good this helicopter is.
MightyTighties 1 year ago
Just a quick note. Since this video I got the bottle to engage the 3D switch and it really improves vertical stability. No more bobbing up and down. I guess I must have got the throttle curve or pitch curves wrong so I am at wrong rpm for stable hover.
itssssssme 2 years ago
Yer that's a point. When you plug the battery to the helli yo need to leave it stood still until the gyro led is constant red. you will also hear the servos jump into position. Only then can you pick it p and move it to the take off position better still connect up in the area you are going to take off from. I think that this function is to orientate the gyro to its settling position.
YasmiinTbh 2 years ago
hey we just got one and we cant figure out why it wont stop spinning, the trim for the rudder doesnt work so could it possibly be that?
hamblingpeter 2 years ago
yes but you should be able to compensate with the sticks, or by adjusting the servo distance. if its second hand it could be the gyro is bust or the belt is on the wrong way, or even the rudder blades fitted the wrong way. this would make it snap into a spin.
itssssssme 2 years ago
Dude i had the same problem right. so i read the intructions and it says do not turn on the Transmiter [remote], so i didnt [i can hear the gyro started making wierd sounds and such, then after it was finished, the blinking light on the gyro was constant Red. But BECAREFULL!! During the gyro stage thing[ where its testing its functions] It tests everything, and i mean The over drive switch for 3D Stunts. so what you should do is put sumthing very heavy on the landing gear stuff.
Chaotic6666 2 years ago
cause i wasent aware tht when the remote was turned off it would test everything. when i did it it almost broke one of my blades but thank god it was carbon fiber lol
Chaotic6666 2 years ago
thankyou for the suggestion. 3 its my 3rd week and have crashed it many times and replaced parts many times.
AfghanKnight007 2 years ago
hi i have one of these, my first 6ch. but it really un stable , just drif to one side as it leaves the ground. even after treaming. is me not a good pilot or the heli has some problems. thanks
AfghanKnight007 2 years ago
it could be jeclone already posted the answer. Try getting off the ground a bit higher to remove the effect of the rotor wash. Also start in a hall to eliminate any breeze and that way you will know if your settings are good or the conditions are bad. Good luck.
itssssssme 2 years ago
Yep its not too hard to fly at all. The best bit is it aint expensive to repair. I would recomand a couple of main shafts and a few landing skids extra. Also try to fly in no wind or sports hall. I cant compare to anything on the market today cos I havent flown hellis for about 20 years and that was on a fixed pitch so this one seems real easy.
itssssssme 3 years ago
hey i cant seem to find any cheaps main rotor blades , at the local hobby shop there aus$59 for a set of carbon fiber ones can u help me out.
setforlife112 3 years ago
There are other cheap blades that will fit.
congoharrison 3 years ago
I just bought some wood blades in white for £7.00 I prefer them to the black carbon as you can see them better. Leeds model shop UK.
itssssssme 2 years ago
hay is that the twister cp gold is it easy 2 fly as ime lookin 2 get 1
rickovgy 3 years ago
you might want to fly a little higher to get it out of the ground effect.
jeclone 3 years ago
Looks like Im trying to bop worms =P
itssssssme 3 years ago