I have run the bike over 1000 miles ,good compression,good oil pressure. Wlii post a video of it running on the street and reving over 10,000 RPM. in a few days if I find the time.
@TestECull i dont think you understand, the point of bedding bearings is to get em to be "comforable" before putting strain on them so they dont wear as quickly
@gibbo1112 I know exactly what bedding bearings in is, and it should be done with the engine running. You aren't going to damage the bearings running it under light throttle, low RPM conditions for a couple thousand miles, and if that is enough to affect their lifespan they were defective or improperly installed.
Bed in bearings? are you not concerned that you are wrecking any chance your engine had of getting a good ring seal by turning the motor over so much with no load on the rings?
BAD ASS!!!!!!!!!!!
guzzinerd 1 month ago
sounds good
WARD5KUSTOMZ 1 month ago
my mouth is watering
ryanwykes 1 month ago
great work :)
sprocket2cog 2 months ago
very nice,,,,how about a V4 or V6 Guzzi?
23vin850 2 months ago
how many years does it take to do the valves???lol
ismokewead420 3 months ago
Will someone make me a 454 c.i. v-8 two stroke?
davetileguy 3 months ago
@davetileguy that would be sick
ismokewead420 3 months ago
@davetileguy make it yourself
crazyredneckwifknife 2 months ago
@crazyredneckwifknife You know when I retire I just might.
davetileguy 2 months ago
I have run the bike over 1000 miles ,good compression,good oil pressure. Wlii post a video of it running on the street and reving over 10,000 RPM. in a few days if I find the time.
dieselguzzi 4 months ago
Should be doing this by running it.
TestECull 6 months ago
@TestECull puts less pressure on un bedded bearings...
gibbo1112 5 months ago
@gibbo1112 If the bearings can't handle idle --> 3K at low throttle they aren't fit to use at all.
Start the damn thing up.
TestECull 5 months ago
@TestECull i dont think you understand, the point of bedding bearings is to get em to be "comforable" before putting strain on them so they dont wear as quickly
gibbo1112 4 months ago
@gibbo1112 I know exactly what bedding bearings in is, and it should be done with the engine running. You aren't going to damage the bearings running it under light throttle, low RPM conditions for a couple thousand miles, and if that is enough to affect their lifespan they were defective or improperly installed.
TestECull 4 months ago
@TestECull ...yea, makes sense... ok
gibbo1112 4 months ago
i thought that are 2 honda cb 750..
Awesome work!
Do you know if was made a hayabusa or a bike with a v8 hartley-hayabusa?
nicodanger13 9 months ago
how is this done? do you have a link to a sight or something... anything that will explain this better????!!!!????!!!!????!!!!????
jacobgnarlif 10 months ago
Bed in bearings? are you not concerned that you are wrecking any chance your engine had of getting a good ring seal by turning the motor over so much with no load on the rings?
RIPSNZ 1 year ago 2
even sounds good just being turned over. very talented man if i may say so.
spoddog1 1 year ago
What donor engines did you use?
akumabito2008 1 year ago
@akumabito2008 They are Hondacb350F cylinders and heads.
dieselguzzi 1 year ago
Very bad camera usage.
stevepitbull 1 year ago