Pulse Motor 001

[lixing3044]

Bored



[ZebbMassiv]

You're awesome.

[Jamieduk999]

do you use iron or steel core in the middle of the coil ?

[TheDieselGene]

put a magnetic switch in the circuit to tell it when to pulse =)

[DjJohhnyIsAtLive]

if you added a magnetic reed switch you would have to continuesly touch the battery

[db29db29]

yay maplin PP3

[henrykay01]

I invented a breakthrough energy source which violates the law of energy conservation. I have a PROOF that there are electrodynamic phenomena which violate the law of energy conservation. I am looking for $30 000 for a prototype and for $3M for patents. Making a 15 kW generator will cost $1200 in mass production. Value of energy produced yearly about $10 000.

H. Tomasz Grzybowski

tel. +48-512-933-540

[vik95170]

it's bad,

[1a2bcea]

Hi Paul,

Its a pity that you could not repy to the comments I made about the Rodin coil.

Its much like telling a Catholic there is no

God.

Faith, blind faith and ignorance.

Its killing real science.

No reply is required.

[1a2bcea]

In Physics you can not get something for nothing. This Rodin is not working for a better future for

anybody save himself by asking for money, and surrounding his website with pseudo scientific bullshit, to put it plainly. I do not mean to offend, if you have any question I would be happy to answer them for you.

By the way, nice signal generator.

Kind regards

Peter May

Sweden.

[1a2bcea]

There is much more to learn, and the internet is a wonderful

source of information if you know where to look.

Next may I say you will not find the facts, or serious science in people like this Rodin character.

He is at best a con artist without much education, and not someone I personally would trust.

These are just a few simple facts Kubikop, my reson for mailing you is to expose these people for

what they are. I have worked with HiFi for many years and I know what I am talking about.

[1a2bcea]

You would also arrange the field generated by the the coil to intersect the permanent magnetic field

at 90 degrees this will increase the efficency of the loudspeaker, in principle the more turns the better

but there are engineering limitations in the real world.

Normally the wire coil mounted on the bobbin is attached to the cone of the loudspeaker thus acting

as a piston to move air to your ears.

[1a2bcea]

What you have made is a simple loudspeaker, albiet a very innefficient one where normally the

coil wound on a bobbin is suspended in the flux of a permanent magnet.(The coil moves not the

magnet). Less mass to move.

For more information look at, Principles of loudspeaker design" on the internet, there are many

sites dealing with this subject.

[1a2bcea]

Hello Kubikop,

My name is Peter May I have been involved with electronics for the last 40 years or so, if you are interested in real science, physics, and the facts read on.

The coil you have wound on the palstic tourus is not a Rodin coil, or a rubik coil, it's just a coil of

wire.

If you have to give it a name then I suggest a Faraday coil, Michael Faraday having laid the foundation

for electromagnetism.

[kubikop]

Hi Peter

That is a lot of posts....I feel like I have been spam'ed! This is a pulse motor. If you want to talk about my other projects could you do it on that video? I thought William Sturgeon invented the first ever coil, but Faraday built on his work. I could be wrong though....

Anyway thanks for taking the to watch my videos and there must be more to learn than what is already out there or in books. I have never tried to trick anyone did you take a look at my plasma speaker?

Thanks

Paul.

[holycrapapie]

you should try playing with reed switches on this thing, get it automatized!

[kubikop]

I used reed switches in my later videos and you start to get a nice fast motor..

Paul.

[Stoney3K]

@holycrapapie You can also pull the exact same assembly out of a standard PC fan.

It's just a DC brushless motor, fans use Hall effect sensors just to get rid of moving parts.

[rroge5]

i have no idea where to get so much magnet wire in ausrtalia, it seems to be impossible.

[rollingagain]

maybe if you ask for "cooper wire"

:)

[joebro391]

how did you affix the magnets to the hard drive platter?? thanks

[kubikop]

I cut rectangular slots, then sand papered the slots. I placed the magnets in the slots and soldered them in.

You could use a hot glue gun though?

Paul.

[joebro391]

ahh, thanks man!

[kubikop]

Make a video once you got it running, and put a video link in!

Good Luck.

Paul..

[SKYSURVEYOR]

*****5***** very good !

[kubikop]

Thanks

[gersfc1]

wer did u get the equitment

[wayne205stevens]

You could use a reed switch to trigger the pulse maybe? just an idea, Im just finishing off my Tesla coil now, need to find some better diodes first though :) love your page by the way! lots of great ideas!

[kubikop]

Ill have a look at your tesla coil if its uploaded!

Paul..

[joebro391]

what did you mean that the coil had 15 ohms?? i know ohms measure resistance, but i've never heard of a coil, being measured by its resistance. I'm still a noob at this, so maybe it's just something i haven't picked up yet. thank you, very much.  -Joe

[kubikop]

Hi Joe

Its just my way of getting an Idea of how long the wire is.

If I wound two coils with 15 ohms and 30 ohms I know that the 30 ohm one is twice as long if I use the same wire.

On a transformer you can measures the resistance on both sides and calculate the ratio of the transformer.

Paul.

[XmarksTheSnot]

I just discovered your videos because of my dad and I think they are very cool. I was wondering what does "the back EMF" mean?

[Demoman42]

You just pushed me to make pulse motor ;D wait for video response ;)

[kubikop]

Do It! its easy you need to be mindful of Resonance though...

Paul

[darrelleric]

How did you get the coil to push ,all magnetic coils i have made pulls, they dont have a N or S

[kubikop]

Swap the leads on the coil........

[edstar83]

great work. I dont normally subcribe to people but i added you to my collection.

[edstar83]

free enegry doesn't exist? what the hell is solar power? wind? water?

[WC9456]

well the sun runs off of mostly hydrogen, which isn't free there is a limited amount but theirs a lot so its pretty much free, and wind is pretty much free i guess, and water takes the suns energy also. but yeah sun wind and water are great energy recourcess

[netlethe]

Don't listen to the spoilers, like the one below .. great work .. keep it up, you'll find "over unity" in my playlists .. there for all to learn from, including "the spoilers" .. hope you'll join us ..

[CDdriveJAMER]

lol 9v maplin battary i buy all my electrical stuff from there

[kubikop]

Same Here!

[warmingtone]

I am looking at doing things with the TT and stuff like this. For a tesla turbine you would get pulses of electricity using this setup in reverse, spinning the disc would produce electricity in the coil like a generator!

This is not an overunity device though...you still need to provide the power or with TT air or water power.

For a low tech version, rather than a 555 circuit, use a reed switch activated by the magnets to send pulse in time with whatever rate of spin and no friction effects!

[PsychoMatt01]

Any idea on how to make this outta magnet wire and the tesla turbine ?

[palehorsepalerider]

its a brushless motor. OK, I have a couple in my computer - OEM.

so..........

[kubikop]

How are the ones in your computer used?

[enemyindisguise]

ehhm... the "TRANSRAPID" "magnetschwebebahn"  you know ?

btw ,my neighbor try to fly with feather.

but .. greets from berlin.

[htmlbandit]

Very cool! Could this be built on a large scale with a Tesla coil?

[kubikop]

Thanks

I am sure that you could integrate it I have had thoughts myself.

I have put off doing my tesla coil for a while though until Im happy with is..

[SimpStone80]

very interesting, thumbs up!

I think I will experiment with this too when I got more time.

[kubikop]

Thanks.

[ehrenk1]

funny i had a vision of a future engine that operates on these principles. by having coils surrounding this cylindical wheel and measureing the angular distance vs speed on the central wheel a microprocessor could determine which coil to electrically charge next and pass the overunity onto the next fired coil for a variable speed device. really its the same principle as the pulse motor just on crack and adaptable.

[kubikop]

Sounds good. Build it....

[ParapaDrifter]

or similar to a combustion engine, pulse the magnet at top dead center... lookie here "Maxforce engine"

[RunandGunPictures]

All except the over unity part, which is indeed impossible.

[Nabo00o]

But free energy is possible. True over unity would over course mean that you really get more energy out of a system then was put in.

[RunandGunPictures]

Define Free Energy. Cause you could claim that having a hot air turbine was free energy by places a glass funnel in a desert with a propeller inside turning a DC generator and you'd have "free" energy in the sense that you don't pay for it. But in reality you are just transferring one form of energy into another and losing a lot in friction along the way. Now Over Unity, that is impossible.

[Nabo00o]

That's exactly what I am talking about.

But free renewable energy is not necessary limited to ambient heat, solar, hydro- and wind power, there could be other sources too which we haven't discovered yet, and which could be even more accessible and powerful.

We cannot simply conclude with that we know all there is to know, and that our theories is faultless. Look at the electron for example, this charge continues to exist and give of energy without loosing its momentum at the same time.

I

[WC9456]

law of conservation of energy states that energy cannot be created nor destroyed. but some people argue with this law, as generators can run on permanent magnets with a little help of electricity and can produce more energy then it uses

[ewigkase]

this has helped me thanks nice and simple no diodes or resistors.

[kubikop]

Time to build your own....

[mcpotplant]

i like at the end you yeeep

[kubikop]

yeeep. I do that a lot.....

[gabydewilde]

I love how everything is self explainatory. This is the perfect video for anyone to start with.

[kubikop]

Hopefully people will build their own from these videos. ;-)

[gabydewilde]

good show.

:-)

[kubikop]

Thanks, I have took it much further since this.....