this has nothing to do with the video but i have some buddies of mine that i now call the Pussy Whooped Crew and your license plates have tose nitials lmao....nice ride by the way
this has nothing to do with the video but i have some duddies of mine that i now call the Pussy Whooped Crew and your license plates have tose nitials lmao....nice ride by the way
i know you probably explained this before, but i dont feel like going through 10 pages to look for it...What do you mean by fully built motor? what have you done to it???
Around $300-400 I've heard. On an OHC motor, though, the cams aren't hard to put in yourself, provided you have the proper tools. I've helped replace a cam on a friend's 5.0 (pushrod/OHV motor) and it was a PITA compared to overhead cam swaps.
For me the timing chain setup is easier on an OHV Motor, a lot more room in the front to move my hands around and get the cover off. I dunno, the only SOHC and DOHC motors I've done are Mercedes Benz's (Factory Trained Mercedes Tech) but I greatly prefer doing a single cam on an OHV then doing a SOHC or DOHC motor, a lot less marks to line up, a lot less special tools needed (at least in this case) and I actually Enjoy having to lash the valves like on a 350 Chevy :D
Understood! To each their own, definitely. As a trained Mercedes Tech, I'm sure the simplicity of a pushrod SBC/SBF cam swap would be an awesome change from the technical side of automotive work like Mercedes.
as long as you get a roush, saleen, or shelby supercharger installed by a certified technician, respectively, then your warranty shouldnt be void, but consult your local ford dealer before installing any forced induction or supercharges
Lope has a lot to do with tuning and idle set speed. I have mine at 900rpm and this one sounds like it's about the same. too much lope and you're dying with a manual trans.
That is a perfect sounding street cam for a late model. Just enough to know you got something, nics smooth tone, bet it barks when you stab it and makes good torque everywhere. This coming from a Chevy guy.
it would sound alot better if it was louder....but its clean...my dad has a 79 442 cutlass....the motor he's puttin in it has a comp cams cam with 300deg. duration 250deg." @.050 lift .560lift.....its bad ass....the motor hes got now is smaller but it has a cam chirp in it....its bad ass
thats one sick ride you got. sounds and runs amazing. did you go with teh supercharger first or the cams? I am going to throw in a novi2200 on mine but love the cam sound too. DId you haev to rebuild the bottom end? I was told once that the stock crank can only handle 500rwhp. Did teh cams make a big difference? Sorry for all the questions, I just want to follow a successful build like yours so I can have the fun that you are.
It's better than sex...
Helraiserftw 6 months ago
That car sounds soooo mean. That's fucking sick.
Intensem0t0rsp0rts 9 months ago
this has nothing to do with the video but i have some buddies of mine that i now call the Pussy Whooped Crew and your license plates have tose nitials lmao....nice ride by the way
aresapimp 1 year ago
this has nothing to do with the video but i have some duddies of mine that i now call the Pussy Whooped Crew and your license plates have tose nitials lmao....nice ride by the way
aresapimp 1 year ago
thats exactly what i want to do to mine
JonathanRattayGT 1 year ago
i know you probably explained this before, but i dont feel like going through 10 pages to look for it...What do you mean by fully built motor? what have you done to it???
lethaldosage6040 1 year ago
@lethaldosage6040
pistons,rods,crank, balanced and blueprinted. A built shortblock!!
conroyz28 1 year ago
@conroyz28 i wana do this to mine but damn....getting all the details would be difficult and annoying. just gonna leave it at this, badass car.
lethaldosage6040 1 year ago
what model number are those comp cams?
firestang70 2 years ago
you should aim to get 888 bhp to match your plate :D
ratgreen 2 years ago 4
what does stage 4 mean? I would rather know the specs on this cam.
weewoodeal 2 years ago 4
you people who leave these stupid comments prob couldnt afford to put gas in the car let alone a cam job.
gtboss281 2 years ago 2
i doubt it costs anywhere near that cheap for a pushrod engine.
M3MPH1SM0J0 2 years ago
how much does it cost to install cams?
Heezy2090 2 years ago
Around $300-400 I've heard. On an OHC motor, though, the cams aren't hard to put in yourself, provided you have the proper tools. I've helped replace a cam on a friend's 5.0 (pushrod/OHV motor) and it was a PITA compared to overhead cam swaps.
302GTS 2 years ago
I would much rather do a cam on an OHV motor then on a SOHC or DOHC motor lol
Chrono348 2 years ago
Damn! Any reason why?? I've helped do cams on a Civic before (DOHC b16), and it was really easy compared to a 5.0 IMO.
302GTS 2 years ago
For me the timing chain setup is easier on an OHV Motor, a lot more room in the front to move my hands around and get the cover off. I dunno, the only SOHC and DOHC motors I've done are Mercedes Benz's (Factory Trained Mercedes Tech) but I greatly prefer doing a single cam on an OHV then doing a SOHC or DOHC motor, a lot less marks to line up, a lot less special tools needed (at least in this case) and I actually Enjoy having to lash the valves like on a 350 Chevy :D
Chrono348 2 years ago
Understood! To each their own, definitely. As a trained Mercedes Tech, I'm sure the simplicity of a pushrod SBC/SBF cam swap would be an awesome change from the technical side of automotive work like Mercedes.
302GTS 2 years ago
@Heezy2090
it was free
When I had my motor built. Gave GEARHEADS in Arlington,Tx the cams and they swapped them out
conroyz28 1 year ago
Can anyone tell me what a camshaft and or supercharger does to the factory warranty? if you get it done by ford will they not void it?
cliffymorris 2 years ago
If I'm not mistaken, you can put a 5 PSI Roush Charger on a '05+ Mustang and retain the factory warranty.
UnsulliedSpy 2 years ago
as long as you get a roush, saleen, or shelby supercharger installed by a certified technician, respectively, then your warranty shouldnt be void, but consult your local ford dealer before installing any forced induction or supercharges
ADD8oi 2 years ago
voids it
rulecar961 2 years ago
@cliffymorris
depends on where you take it for service
conroyz28 1 year ago
were all sure it sounds good man we just couldnt hear it how about a few revs or a launch or something
hemiram08 2 years ago
faggot!!?? HAHAHA
Robergjj 2 years ago
lol
Karnage542 2 years ago
I must agree with
NCRamUSMC
silversol 3 years ago
i am truely jealous
NCRamUSMC 3 years ago
how much did it cost to get it installed
coolguy23448 3 years ago 2
Lope has a lot to do with tuning and idle set speed. I have mine at 900rpm and this one sounds like it's about the same. too much lope and you're dying with a manual trans.
rrtx2007 3 years ago
haha yea got a vette with the lsx 427 and got the lope reallllll low and it dies constantly
THESNAKE8 3 years ago
This has been flagged as spam show
nice check out my vid with even more stuff done
paintballer0816 3 years ago
stock mufflers?
charger12 3 years ago
@charger12
flowmasters
conroyz28 1 year ago
That is a perfect sounding street cam for a late model. Just enough to know you got something, nics smooth tone, bet it barks when you stab it and makes good torque everywhere. This coming from a Chevy guy.
Nice ride
1375355 3 years ago
how much is involved putting the comp cam in ur mustang, because i am thinking about doing a cam in my gt mustang
StngRayCorv 3 years ago
it would sound alot better if it was louder....but its clean...my dad has a 79 442 cutlass....the motor he's puttin in it has a comp cams cam with 300deg. duration 250deg." @.050 lift .560lift.....its bad ass....the motor hes got now is smaller but it has a cam chirp in it....its bad ass
PBownz55 3 years ago
i bet it's bad ass
elmarko99 3 years ago
thats not a bad lope at all, i like
praetorian2150 3 years ago
Did you have to switch out the valve springs?
charliedip 3 years ago
yes.. Switched them out with some stiffer springs..
conroyz28 3 years ago
Where do you live in TX? I'd love to talk about those cams. Considering cam swap in mine as well...
rrtx2007 3 years ago
Sounds great. I was wondering what kind of mods or if any are needed when installing these or any performance cams?
lucio22222 4 years ago
love procharger tho. sick car!!!
lldsandsll 4 years ago
i didnt think it was a good idea to go higher than stage 2 w/ a blower
lldsandsll 4 years ago
thats y he has a fully built motor
calledtoduty2000 4 years ago
thats one sick ride you got. sounds and runs amazing. did you go with teh supercharger first or the cams? I am going to throw in a novi2200 on mine but love the cam sound too. DId you haev to rebuild the bottom end? I was told once that the stock crank can only handle 500rwhp. Did teh cams make a big difference? Sorry for all the questions, I just want to follow a successful build like yours so I can have the fun that you are.
fastandfurious76 4 years ago
What are you running for exhaust on that beast?
Redfire05GT 4 years ago
I am running BBK longtubes, offroad x-pipe and flow master mufflers....
conroyz28 4 years ago
how much for those that pretty much exactly what i will start off with
tell me the price including installations
vidalthegreat88 4 years ago
really? cause the comp. camshaft IV description says it has a VERY VERY rough idle, so its just rough as hell on the outsie but cool on the in?
onepixedpup 4 years ago
how bad would you say the idle is? is it like shakey as fuck? cause it definitely sounds badass as fuck! beautiful car
onepixedpup 4 years ago
When your in the car you cant even tell really that it has a cam.. very muild inside....
conroyz28 4 years ago
idle is perfect..When in the car nothing rattles or vicrates.. Its the perfect cam in my opionin
conroyz28 3 years ago