Free energy is finaly here!But Elite controllers don't want ppl to be free from the costs of energy,Get a real free energy motor at LT-MAGNET-MOTORdotCOM ,Join the revolution!
I would caution you in the area of safety for what it's worth. When I was in Air Force electronics class always remove jewelry. A ring for example if shorted across a powerful enough circuit can burn your finger off! The chain bracelet if it were shorted across the battery terminals can burn your hand off or damage the tendons and blood vessels to the point that amputation is required. Anyone can say by viewing the video that this can't happen but, if safety is observed you'll be ok.
I am using the same set up and am using about 870 ohms of resistance. I get a return of about 9.5 volts. How are you getting such a high return to your recharge bat?
Can you please show how you hooked up the electronics?
I noticed that your potentiometer is using the middle connection and the right connector. What I have been reading and noticing from others, is that the use both connectors on the ends and don't use the middle. Is this why you are getting a sound?
I would like to communicate with you about the physical part (plastic, and other parts of the most). All the parts except the electronics. I am cmanis1 (at) yahoo (dot) com, Thanks
Hi Ktservicecorp and all, the buzz you hear is coming from the transistor, is getting extra oscilations besides the rotor oscilation freq. Use a darlington, like TP112, the buzz will be disapear mostly. When the charged battery. As an engineer in electronics, please let this thing going for a month and then we can put the results on a piece of paper. I understand how it's working but no way this is free energy. If any one has some results in this free energy direction, is welcome to contact me.
However, the voltage your multimeter is reading from the circuit when you pulled the battery off is wrong. you need to switch your multimeter to AC voltage not DC voltage in order to record the spikes properly
On the light, your load battery may act as a regulator. Fox example, my Honda bike uses a 6 volts battery as a regulator, if the battery is disconnected, all works well but the lights are burned as the voltage in the circuit is higher and not regulated.
The noise may me electrical but you may consider that it may be acoustic. It may be produced by the magnet surface being higher than the surface of the pipe shaft and acting as fan blades.
I hope this will help you understand why you're getting the different readings between the charging battery terminals then without the charging battery connected.
i think its how u put the wires cus u do have quite a jungle there try puting the wires away from each other kinda like a woki talki if there to close they make a sound so try that out
ur led lights up cuz the power has no where else to go. the led is a sfety device or the energy would turn into heat (E=MC2) and start burnin the weakest part of the whole thing....any help??? ;)
from what ive read the neon bulb only lights when you have too much current. if the light were not there you would be burning out your transistor.
ive built a small bedini motor. i got noises like the ones you were getting right before i burned out one side of my pot - but i was not able to get my motor to spin while i had the high pitched noises.
i think what you want to do is get the motor spinning as fast as it can. your motor looks to be doing better than mine
yeah your voltage is a little bit 2 high by about 5 volts maximum for a 12v battery is 13.5 or q3.4 but any higher and you can wreck the plates so see if you can get some kind of voltage regulator from radioshack :) or make one lol
try getting some neodymium magnets they are more powerful. the magnetic field with the magnets you have are not reaching the bottom of the coil and the noises might be a speaker effect from the area not in the field.
I think the sounds are coming from your stator. I've witnessed that from transformers, which are basically the same thing but used differently. I'm guessing the bulb is flashing brightly since your battery isn't connected, the power doesn't have a battery to charge... But I'm not an EE. Nice construction. Just ignore the holier-than-thou scientists and engineers who comment here. Better yet, just delete their comments.
When you build an amplifier circuit it can sometimes be prone to spontaneous oscillation. You a working with an active circuit that has an amplifying transistor in it. There is stray capacitance associated with your coil. This makes an LC circuit that can resonate with the amplification provided by the transistor.
Ignore the idiot "know-it-alls". "Music of the spheres" sounds are partly coming from MAGNETS STRAINING TAPE as rotation increases. Hey: instead of wrapping wire around whole thing - wrap on an OUTER CYLINDER AROUND each magnet set! Then parallel out to controller of 60v 3000w mag-drive on your reverse 3-wheeler (see Yamaha custom: BioMod "Ultra-Vees": Can-Am spyders). You will need about 30amps at 65v or so; maybe six magnet sets - put in caps as buffers.
sorry for the comments, build and have fun, better than watch tv anyway. volts and amps are diffrent sides of the same thing. To accurately measure load you have to filter and measure both volts and amps and the mulitiply to get watts, then calc incomming and outgoing watts then you can tell weather the mashine produce 400% electricity, pulse charge a battery to reach x volts dont nessesairly say its fully charged.
I agree. The more I learn about this, the more I know I need to learn. I don't believe in OU, it is an oxymoron. I do believe that there is more power in a magnet than it takes to produce. It is like tapping into an atom (kaboom). A long term reaction takes place when a high powered magnet is made just like the rods in a nuke plant. The energy last about twenty years. A small nuke plant on a sub last about that long. Our future is just about making clean electricity. Then we just have to plug in
I feel so sorry for all these guys with no electrical knowlege thinking they stumbled on something big. google step-up converter, learn the basics more intresting taping magnets on a toilet roll, sorry
I agree. My father was an electrical engineer and he just laughs at this stuff. It's still fun to watch these guys. Wonder if ktservicescorp knows what a capacitor is?
yeah, the circuit probably rotate in the 4th dimension, that causes the sound.. *spokey* transistor ohhha.. my computer got millions of these and still not communicating with outer space or the other side..
lol... your comments are quite refreshing. When is the last time you built a motor or did anything constructive. My ignorance is laughable especially since I don't do electrical engineering while making 300,000 a year. Those that can DO...those that can't CRITISIZE :) Fortunately I now have the time to learn. What do you do for a living Einstien?
your income is intresting to whom? dont know why you try to brag about your ignorance, but anyway.. stupid of me to comment this bendini-stuff. rednecks can build whatever as long as its fun. Obviously you dont know anything about me and guess I dont know stuff. I have been doing electronics since I was a kid, and has studied it. btw make more than you as a programmer now
Hi, I'm wonder how strong is this motor ?? And how many hours does the motor run at one battery ?? Is it possible to connect a wind generator motor (low RPM) as power generator to produce energy ??
when the light is brighten, then u r getting back emf, that is over 200volts spikes, so with no load(the battery in this case) all energy from motor goes to light bulb. youll be get shock if u touch the wires from coil without the load.
other thing, it should be neon light not normal light. neon light is for high voltages like over 90volts and so on.. u can find neon light example almost all electrical things where is lighted switch, inside switch have neon light.
I started with a 5k pot and it created high frequency pitches. Then I want to the 1k pot the circuit called for. Go to Fry's electronics. They have 1k pots.
I believe that the sound is coming from the hollow coil it is more like blowing across the top of a bottle. Maybe if you tape across the top of the spool your coil is made from your whistling sound may quit. Or maybe I am way off base, but, you won't fail by trying and you can disprove one incorrect theory which is progress itself.
I was wondering about that. I have heard of ionic wind. I saw a show on the science channel about some guy making hovercraft with ionic wind. Needs very HIGH voltage but hey keep the amps VERY low and you can only get a serious shock. :)
I'm posting this message here because, I Just don't know how to send you a message directly, I have a project going on in witch you don't use a rotor Just an toroidal transformer winded w 5 primarys to work @ 12v 1.5 Amps,and a Secondary to obtain a 220V AC making it pulce with a microcontroller, if you are interested, I really will find my self privilege to exchanage a few Ideas
The Noise is more than likely low frequency RF bieng resonated off the coil through the potentometer would like to see a like to see what the O scope would say on bolth the coil side and the emmitter side of the pnp
With this motor it would fall apart. I need perfectly machined parts like you just found. I have a large 2hp motor with a heavy rotor that will handle it but haven't decided how I want to do that yet. Linderman built a bedini motor using an electric motor like mine(2hp) and achieved 3000rpms. If you find out how to wire up an electric motor to make the circuit work please let me know.
Here is one thing I have heard about the interaction with the charging battery and the electricity. Please try this if you can.
Take a neon, disconnected, hold on lead in your hand between your fingers. Go over the plastic parts on top of the battery with the other that isn't connected to anything. See if it lights up.
try a car coil connected to the secondary bedini coil .... shocking ..lol
you will notice that the electro static power travels over the wire .but the bedini system gives you both (shunting electrons along) its fantastic stuff
If your trigger resistance is high, it will self resonate, keep triggering itself. I think it has to do with the capacitance of the coil.. If you look on the scope you will see more than one radiant spikes on each pass of the magnet. Lower the resistance on the trigger a bit to get rid of it if that is what you want to do. Should make the motor go a bit faster as well.. As for the light, not sure where you have that in the circuit.. sorry..
The bedini circuit doesn't call for that strong of magnets. They are ceramic magnets I got at home depot 2 for 2.65. Heck even the fueless engine plans only call for N38 mags. N45 are VERY strong. If you are building a pulse motor for sheer torque then they will be perfect.This motor has very little torque. My first motor(pulse) has 5 times the torque
Hello great work for only 4 months at it, in the above post you mention "fueless engine plans" where did you find these? do you have the web address or are these not free on the web???
The sound is normal it is residence with the core. It is even in the Bedini videos with his circuits. The light protects your transitor from getting fried.
you guys ALL have a hand in my inspiration. 4 months ago I didn't know a thing about any of this stuff and now I am building HHO generators and patented circuits lol... I still don't have a clue but at least I am not sitting on my ass letting others think for me! I know there is something to all this.Thanks again for your support!
This has been flagged as spam show
w w w diymagneticmotor com has something for FREE energy,... ?
tyuiwas 7 months ago
This has been flagged as spam show
watch my video
Ali2011mb 11 months ago
I will see you in an hour!
rob1sh 1 year ago
This has been flagged as spam show
Free energy is finaly here!But Elite controllers don't want ppl to be free from the costs of energy,Get a real free energy motor at LT-MAGNET-MOTORdotCOM ,Join the revolution!
lutherarao 1 year ago
This has been flagged as spam show
Free Energy is real but the coverup is strong, if you are interested in a REAL free energy machine then
just search for the LT MAGNET MOTOR in the youtube video search , it is probably the ONLY working magnet
motor out there. Join the free energy revolution!!
violafinishda 1 year ago
Have you anything that can mesher your magnets and if there is a fault in them!?
By that i mean some magnets the S and N are not inline or they are not where they should be.....!!?
Ebdan88 1 year ago
I would caution you in the area of safety for what it's worth. When I was in Air Force electronics class always remove jewelry. A ring for example if shorted across a powerful enough circuit can burn your finger off! The chain bracelet if it were shorted across the battery terminals can burn your hand off or damage the tendons and blood vessels to the point that amputation is required. Anyone can say by viewing the video that this can't happen but, if safety is observed you'll be ok.
1foxtrot70 1 year ago
I am using the same set up and am using about 870 ohms of resistance. I get a return of about 9.5 volts. How are you getting such a high return to your recharge bat?
chipsnyper06 1 year ago
you can ear the noise because the rotor is blocked.(on sides)
If you fix the rotor useing repulsive magnets you can do it mauch better (to have an idea it is like trains on magnetic rails)
JohnnyDTK 1 year ago
the od nois is wind from the magnets blowing past the coil
bcdigit 2 years ago
Can you please show how you hooked up the electronics?
I noticed that your potentiometer is using the middle connection and the right connector. What I have been reading and noticing from others, is that the use both connectors on the ends and don't use the middle. Is this why you are getting a sound?
pkrska 2 years ago
whats the wire guage and winds on the coil
williewithwttw 2 years ago
sounds like an UFO ;)
jacek533 2 years ago
I would like to communicate with you about the physical part (plastic, and other parts of the most). All the parts except the electronics. I am cmanis1 (at) yahoo (dot) com, Thanks
jake1aa 3 years ago
Hi Ktservicecorp and all, the buzz you hear is coming from the transistor, is getting extra oscilations besides the rotor oscilation freq. Use a darlington, like TP112, the buzz will be disapear mostly. When the charged battery. As an engineer in electronics, please let this thing going for a month and then we can put the results on a piece of paper. I understand how it's working but no way this is free energy. If any one has some results in this free energy direction, is welcome to contact me.
nastasa1234 2 years ago
the bright light is normal...
However, the voltage your multimeter is reading from the circuit when you pulled the battery off is wrong. you need to switch your multimeter to AC voltage not DC voltage in order to record the spikes properly
comwarrior69 3 years ago
On the light, your load battery may act as a regulator. Fox example, my Honda bike uses a 6 volts battery as a regulator, if the battery is disconnected, all works well but the lights are burned as the voltage in the circuit is higher and not regulated.
RL
guitarrarl 3 years ago
The noise may me electrical but you may consider that it may be acoustic. It may be produced by the magnet surface being higher than the surface of the pipe shaft and acting as fan blades.
RL
guitarrarl 3 years ago
Hey nice configuration there!I think I`ll build my next one like that.
71z50 3 years ago
I'm sure you have solved it by now, but wait until you get your core. Don't use neo's because they are too powerfull and will give a backdrag effect.
SJohnM81 3 years ago
Just to help you out on Electronics basics..
V=IxR
V = Voltage
I = Current
R = Resistance
I hope this will help you understand why you're getting the different readings between the charging battery terminals then without the charging battery connected.
scholarlv 3 years ago
i think its how u put the wires cus u do have quite a jungle there try puting the wires away from each other kinda like a woki talki if there to close they make a sound so try that out
rahimi15 3 years ago
I have to agree with antillesrock. Perhaps you need to move it further from the coil.
ReisendeEuropa 3 years ago
ur led lights up cuz the power has no where else to go. the led is a sfety device or the energy would turn into heat (E=MC2) and start burnin the weakest part of the whole thing....any help??? ;)
bratstarr 3 years ago
how far does the field reach from the motor? Maybe move the light away from the motor?
antillesrock 3 years ago
Have you tried the motor running into vacuum of air?
What are the implications of less air resistance?
Let us know please
amfipolis 3 years ago
awesome job!!
from what ive read the neon bulb only lights when you have too much current. if the light were not there you would be burning out your transistor.
ive built a small bedini motor. i got noises like the ones you were getting right before i burned out one side of my pot - but i was not able to get my motor to spin while i had the high pitched noises.
i think what you want to do is get the motor spinning as fast as it can. your motor looks to be doing better than mine
maximillionjones 3 years ago
Are you trying to create and electric motor from the Bedini circuit?
xjedi 3 years ago
yeah your voltage is a little bit 2 high by about 5 volts maximum for a 12v battery is 13.5 or q3.4 but any higher and you can wreck the plates so see if you can get some kind of voltage regulator from radioshack :) or make one lol
Timmys2007 4 years ago
I need to do that.Thank you for the advice. I will reseach how to make one and give it a go.
T
ktservicescorp 3 years ago
try getting some neodymium magnets they are more powerful. the magnetic field with the magnets you have are not reaching the bottom of the coil and the noises might be a speaker effect from the area not in the field.
REG45401 3 years ago
I think the sounds are coming from your stator. I've witnessed that from transformers, which are basically the same thing but used differently. I'm guessing the bulb is flashing brightly since your battery isn't connected, the power doesn't have a battery to charge... But I'm not an EE. Nice construction. Just ignore the holier-than-thou scientists and engineers who comment here. Better yet, just delete their comments.
renderrob 4 years ago
When you build an amplifier circuit it can sometimes be prone to spontaneous oscillation. You a working with an active circuit that has an amplifying transistor in it. There is stray capacitance associated with your coil. This makes an LC circuit that can resonate with the amplification provided by the transistor.
Drevtoobe 4 years ago
Ignore the idiot "know-it-alls". "Music of the spheres" sounds are partly coming from MAGNETS STRAINING TAPE as rotation increases. Hey: instead of wrapping wire around whole thing - wrap on an OUTER CYLINDER AROUND each magnet set! Then parallel out to controller of 60v 3000w mag-drive on your reverse 3-wheeler (see Yamaha custom: BioMod "Ultra-Vees": Can-Am spyders). You will need about 30amps at 65v or so; maybe six magnet sets - put in caps as buffers.
PhotonDrive 4 years ago
sorry for the comments, build and have fun, better than watch tv anyway. volts and amps are diffrent sides of the same thing. To accurately measure load you have to filter and measure both volts and amps and the mulitiply to get watts, then calc incomming and outgoing watts then you can tell weather the mashine produce 400% electricity, pulse charge a battery to reach x volts dont nessesairly say its fully charged.
xsyar 4 years ago
I agree. The more I learn about this, the more I know I need to learn. I don't believe in OU, it is an oxymoron. I do believe that there is more power in a magnet than it takes to produce. It is like tapping into an atom (kaboom). A long term reaction takes place when a high powered magnet is made just like the rods in a nuke plant. The energy last about twenty years. A small nuke plant on a sub last about that long. Our future is just about making clean electricity. Then we just have to plug in
ktservicescorp 4 years ago
I feel so sorry for all these guys with no electrical knowlege thinking they stumbled on something big. google step-up converter, learn the basics more intresting taping magnets on a toilet roll, sorry
xsyar 4 years ago
I agree. My father was an electrical engineer and he just laughs at this stuff. It's still fun to watch these guys. Wonder if ktservicescorp knows what a capacitor is?
inspectorh 4 years ago
yeah, the circuit probably rotate in the 4th dimension, that causes the sound.. *spokey* transistor ohhha.. my computer got millions of these and still not communicating with outer space or the other side..
xsyar 4 years ago
congratulation, you have built an electrical motor, has existed for at least 100years
xsyar 4 years ago
lol... your comments are quite refreshing. When is the last time you built a motor or did anything constructive. My ignorance is laughable especially since I don't do electrical engineering while making 300,000 a year. Those that can DO...those that can't CRITISIZE :) Fortunately I now have the time to learn. What do you do for a living Einstien?
ktservicescorp 4 years ago
your income is intresting to whom? dont know why you try to brag about your ignorance, but anyway.. stupid of me to comment this bendini-stuff. rednecks can build whatever as long as its fun. Obviously you dont know anything about me and guess I dont know stuff. I have been doing electronics since I was a kid, and has studied it. btw make more than you as a programmer now
xsyar 4 years ago
Kinda hard to belive, sence you haven't even grasped the english language...
csorrows 3 years ago
Hi, I'm wonder how strong is this motor ?? And how many hours does the motor run at one battery ?? Is it possible to connect a wind generator motor (low RPM) as power generator to produce energy ??
fryzury 4 years ago
good work!
when the light is brighten, then u r getting back emf, that is over 200volts spikes, so with no load(the battery in this case) all energy from motor goes to light bulb. youll be get shock if u touch the wires from coil without the load.
other thing, it should be neon light not normal light. neon light is for high voltages like over 90volts and so on.. u can find neon light example almost all electrical things where is lighted switch, inside switch have neon light.
riku2015 4 years ago
could you do me a favor and give us the ohms on the pot. I could only get my hands on a 5k pot so I might not have enough control
GraffixWB 4 years ago
I started with a 5k pot and it created high frequency pitches. Then I want to the 1k pot the circuit called for. Go to Fry's electronics. They have 1k pots.
ktservicescorp 4 years ago
The sound is multiple spikes at a frequency at that tone.
joe1001101 4 years ago
I believe that the sound is coming from the hollow coil it is more like blowing across the top of a bottle. Maybe if you tape across the top of the spool your coil is made from your whistling sound may quit. Or maybe I am way off base, but, you won't fail by trying and you can disprove one incorrect theory which is progress itself.
shadowdo 4 years ago
I was wondering about that. I have heard of ionic wind. I saw a show on the science channel about some guy making hovercraft with ionic wind. Needs very HIGH voltage but hey keep the amps VERY low and you can only get a serious shock. :)
ktservicescorp 4 years ago
I'm posting this message here because, I Just don't know how to send you a message directly, I have a project going on in witch you don't use a rotor Just an toroidal transformer winded w 5 primarys to work @ 12v 1.5 Amps,and a Secondary to obtain a 220V AC making it pulce with a microcontroller, if you are interested, I really will find my self privilege to exchanage a few Ideas
Mark
Migueldeservantes 4 years ago
Absolutely! sirHOAX just make something similar. I am not too familiar with toroidal transformers but I will certainly educate myself on them soon!!
Todd
ktservicescorp 4 years ago
The Noise is more than likely low frequency RF bieng resonated off the coil through the potentometer would like to see a like to see what the O scope would say on bolth the coil side and the emmitter side of the pnp
meier25 4 years ago
wish I had one first, second, I wish I knew how to use one lol :)
ktservicescorp 4 years ago
Wonder how hard it would be to get one of these type pulse design up to a RPM of 11,000? What is your thoughts..
Another thing - the roller blade bearings, what is the size of the rod you are using that fits the bearings??
Regards, --S
sirHOAX 4 years ago
With this motor it would fall apart. I need perfectly machined parts like you just found. I have a large 2hp motor with a heavy rotor that will handle it but haven't decided how I want to do that yet. Linderman built a bedini motor using an electric motor like mine(2hp) and achieved 3000rpms. If you find out how to wire up an electric motor to make the circuit work please let me know.
I used a 5/16 rod.
T
ktservicescorp 4 years ago
Here is one thing I have heard about the interaction with the charging battery and the electricity. Please try this if you can.
Take a neon, disconnected, hold on lead in your hand between your fingers. Go over the plastic parts on top of the battery with the other that isn't connected to anything. See if it lights up.
Just curious, --sirHOAX--
sirHOAX 4 years ago
try a car coil connected to the secondary bedini coil .... shocking ..lol
you will notice that the electro static power travels over the wire .but the bedini system gives you both (shunting electrons along) its fantastic stuff
ajpolak 4 years ago
If your trigger resistance is high, it will self resonate, keep triggering itself. I think it has to do with the capacitance of the coil.. If you look on the scope you will see more than one radiant spikes on each pass of the magnet. Lower the resistance on the trigger a bit to get rid of it if that is what you want to do. Should make the motor go a bit faster as well.. As for the light, not sure where you have that in the circuit.. sorry..
memushik 4 years ago
I dont know what makes the sound but if I use my cordless drill and hardly press the trigger the drill make wierd high pitch sound like your bendini.
uncleshorty 4 years ago
Just out of curiosity, how strong are the magnets you're using? By rating, if you happen to know it... ^_^
I ask cause I found some N45 neodymium magnets I was thinking about experimenting with.
wickywickywah 4 years ago
The bedini circuit doesn't call for that strong of magnets. They are ceramic magnets I got at home depot 2 for 2.65. Heck even the fueless engine plans only call for N38 mags. N45 are VERY strong. If you are building a pulse motor for sheer torque then they will be perfect.This motor has very little torque. My first motor(pulse) has 5 times the torque
ktservicescorp 4 years ago
Hello great work for only 4 months at it, in the above post you mention "fueless engine plans" where did you find these? do you have the web address or are these not free on the web???
december105 4 years ago
Having no experience you are doing outstanding work.
Thanks
Jack
dulcajack 4 years ago
You could contact ZeroFossilFuel and JohnAarons, engaged in hydrogen experiments.
JavaLessons 4 years ago
How are you filming this ?
JavaLessons 4 years ago
Sony MiniDV why? I capture the vid to movie maker "high quality small" then post it
ktservicescorp 4 years ago
I mean, you have it attached to a headband or something, cause both your hands are followed and visible.
JavaLessons 4 years ago
I just held the camera like I was on the phone, with my shoulder lol.
Zero said I was going to blow myself up :)and John Aaron's wrote about the soft core iron displacing magnetism the best over welding rods and steel!
ktservicescorp 4 years ago
The sound is normal it is residence with the core. It is even in the Bedini videos with his circuits. The light protects your transitor from getting fried.
marthale7 4 years ago
Thank you! It sounds like I got it right :)
ktservicescorp 4 years ago
you guys ALL have a hand in my inspiration. 4 months ago I didn't know a thing about any of this stuff and now I am building HHO generators and patented circuits lol... I still don't have a clue but at least I am not sitting on my ass letting others think for me! I know there is something to all this.Thanks again for your support!
-T-
ktservicescorp 4 years ago
Why not use a chunk of rebar for your core most of the time its free scrap. It's not the best of cores but works quite well. Keep on going good work.
crazzieg 4 years ago
I am going to do that!
ktservicescorp 4 years ago
Keep up the excellent work.
Thanks for the video post. =P
Regards, --S
sirHOAX 4 years ago