Si necesitas mas ayuda con algunos, puedo ayudarte. Me gustaria hacer mas videos pero mi cubo de rubik esta perdido D: Ojala que vaya a verlo manana....
No se de donde eres pero aqui en mi estado en los estados unidos todos los estudiantes tienen que aprender espanol. Pero practico con gente como tu :D
but this time with the correct orientation, which ends up looking something like (F D F') (D') (F D F' ) (D), follows the rule of XYX'Y', leaving the fixed corner the only U piece changed. Next, move the other corner into the spot of the first one, and perform the sequence you used last time's inverse.
I dont know why that doesnt work for three corners, but I know a way to do it, but thats for you to figure out ;)
You need to find a layer that has incorrect corners, or use a setup tun to bring it to a place where there are two misoriented corners on one layer. Then, you need to orient one of the corners correctly, which i (and other people) do by pulling the corner out of the layer, and then moving it out of the way to put the the layer you removed it from back into place. then, bring it back on to the layer, and bring it back into the top layer (pause)
You should apply some commutators to your "scrambled" room. (kiddin')
Good tutorial like in the corner-3 cycle. Thank you.
heshaaamtube 1 year ago
muy bueno
gracias
lemexio 2 years ago
Si necesitas mas ayuda con algunos, puedo ayudarte. Me gustaria hacer mas videos pero mi cubo de rubik esta perdido D: Ojala que vaya a verlo manana....
Pseudoprogrammer 2 years ago
Si te gustaria puedo hacer unos videos en espanol.
Pseudoprogrammer 2 years ago
oooooooh si por favor!!! increible :D
seria genial algunos ejemplos
lemexio 2 years ago
con scrambles
lemexio 2 years ago
Que typo de video quieres? Yo se muchas cosas con el cubo....
Pseudoprogrammer 2 years ago
me gustaria ver mas ejemplos de Commutators: Corner-3 y Edge-3.. y la explicacion de las conjugaciones que no las entiendo muy bien.
como aprendiste español? :D
lemexio 2 years ago
cual es tu ID wca?
este es el mio 2009SAEZ01
lemexio 2 years ago
No tengo un ID wca. En mi estado no hay los concursos :(
Pseudoprogrammer 2 years ago
pero toma un bus y participa pos! cuanto tiempo haces en bld?
lemexio 2 years ago
No se de donde eres pero aqui en mi estado en los estados unidos todos los estudiantes tienen que aprender espanol. Pero practico con gente como tu :D
Pseudoprogrammer 2 years ago
but this time with the correct orientation, which ends up looking something like (F D F') (D') (F D F' ) (D), follows the rule of XYX'Y', leaving the fixed corner the only U piece changed. Next, move the other corner into the spot of the first one, and perform the sequence you used last time's inverse.
I dont know why that doesnt work for three corners, but I know a way to do it, but thats for you to figure out ;)
nigtv 2 years ago
danielleclain (or whoever may find it helpful),
You need to find a layer that has incorrect corners, or use a setup tun to bring it to a place where there are two misoriented corners on one layer. Then, you need to orient one of the corners correctly, which i (and other people) do by pulling the corner out of the layer, and then moving it out of the way to put the the layer you removed it from back into place. then, bring it back on to the layer, and bring it back into the top layer (pause)
nigtv 2 years ago
thats same as M2
najinajina 3 years ago
Hie
Can you explain how to orientate the last layer with the conmutators?
Thanks
Danielleclain 3 years ago
hie,
can you please explain more slow the conmutators?
saludos
Danielleclain 3 years ago