AR-15 SBR (Taking off the Barrel from Upper)

[captnmuk]

And just invade anyone missed it, "see that notch? Look close, see that notch? That notch right there. See it?"

[Homehous]

who cares about the finish , it is a battle rifle

[curtispa]

i dislike that wrench i broke one in half n cut up my hand

[m16mang]

I learn a lot from your videos.

[erkwit]

"Sup bitches!" *closes video tab*

[Homehous]

hey my bitches,  I notice you shoot on your property. Here in texas you need twn acres to do that. How acres do you have? And is it legal to shoot on your property?

[HammeredAndHorny]

WE SEE THE FUCKING NOTCH! lol

Good video, though. I really like the look of that rifle.

[MultiSr16]

barrel nut torque is only 30 to 40 ft pounds i believe., so def not super tight

[3mealsaday]

I have been seriously looking into buying a 10.5" barrel for my AR. But I know that the registration for a SBR is long and frustrating. So while on my search through the internet and many government websites, I saw where it mentioned that the rifle could not be no less than 16" in barrel length "OR" that it could not be under 26"... With a 10.5" on my AR it will still be over 26" (32" exactly) but with a shorter than 16" barrel. Is this a SBR? The laws do clearly state "OR".

[guns4good]

@3mealsaday From what I can gather any rifle barrel less than 16" is classified by the BATFE as a SBR. Of course that's unless your AR lower is a designated pistol lower, then it can't have any kind of buttstock or it will be an illegal (unregistered) SBR. The BATFE makes it so damned confusing for a reason: it's easier to get into trouble if no one knows what's legal and what's not. It's the same with the "compliance parts" for import rifles; this part is good, this part is not... Write them...

[excaliber454]

@3mealsaday The law should be re-written to say "AND OR". The truth is, any barrel under 16" is considered an SBR.

[Tyson200422]

If you say bitches one more time Im going to park my car in your ass hole LOL great vid

[jhawley1995]

The fabric of my life cotton.

[NorthernShooter]

That wrench needs some duracoat !! DUDE !! give it the nice handle look spary it will be totally awsome dude !!!

[easydoz1]

What does the thing on the upper, right behind the ejection port facing rear and to the right. Do?

[C2builder]

You should have ordered a AR15/M16 Nylon reciever block so you don't have to hold the upper between your legs (not strong enough) when using the barrel wrench tp tighten or loosen the nut. Also, who installed your short barrel for you? Some barrel alinment pins need to be fitted to the reciever pin slot. They did not install it correctly. FWIW.

[black1705f]

@C2builder Yeah, good point a bench vise and a receiver block would be preferable to get that thing torqued down to proper specification.

[TMHonfire102]

@C2builder ya I ordered a AR15/M16 Nylon receiver block, after doing this video, but ya it was not tight at all

[black1705f]

Hopefully tightening the barrel nut on good will fix that wobble. Normally all of my barrels have been snug with the post in that receiver notch. I'm assuming the barrel is not original to the receiver so maybe thats where you got that little bit of play in it. Crank it down good and good luck.

[mikeb1444]

Did you all get that Jack in the box commercial when they're hazing the intern? DUDES, that's not tactical.

[xxbryan715xx]

every time you like this video a tnper gets a kill in his paint ball match

[retardedretard97]

if it scrapes your ar just DURACOAT IT DUDES!

[TMHonfire102]

@retardedretard97 DUDES!!!!!!!!!!!!!!

[fisher1972]

@TMHonfire102 duracoat that barrel instead of tighting the barrel nut dude! duracoat rocks dude!

[TheHiddenPart]

Cool video. Good luck with the reassembly.

IMPORTANT:

DO NOT FORGET TO APPLY ANTI-SEIZE GREASE ON THE UPPER RECEIVER THREADS BEFORE STARTING THE BARREL NUT ON THEM!

[MegaGevehr]

Sunny in Philadelphia kicks ass!

[StiThis1]

fucking trippy as fuck add. fuck . check out my rape vida of my thrown my ar in mud. cuz ar fan boys can get guns dirty too

[semiautoriflelover]

This is why you buy brand name parts. I buy colt barrels and colt uppers so they fit perfect, sometimes these el cheap parts are looser than a street whore.

[ArsenalSGL31]

@semiautoriflelover also BCM barrels and parts are excellent.

[semiautoriflelover]

@ArsenalSGL31 This is a upper from BCM?

[leoffensive]

@Erh4bi chrome speed tests

[aaadream]

Man...just duracote that bad boy .. glad you got your tool doode. Yes I would say it was loose as a goose. LOL Has tex been to your house again? That looked like bacon grease on your upper #LOL

[skipwadoo]

Looks like You Tube is inserting ads before your vid.

[leoffensive]

ahh nooo not an annoying 30 second add

[TMHonfire102]

@leoffensive LULZ! yup i got my partnership back and so did cokeman2423

[leoffensive]

@TMHonfire102 haha congratz! btw what happened to the osprey piston system?

[TMHonfire102]

@leoffensive ill have an update on that piston kit soon when i get my piston back from osprey

[semiautoriflelover]

@TMHonfire102 Why not use an Adams Arms piston kit? These osprey kits seem like junk.

[TMHonfire102]

@semiautoriflelover ya im just seeing what piston works best so far i wish Adams Arms made a low profile piston kit that was pinned not screwed in

[leoffensive]

@TMHonfire102 ahh excellent