i think its running lean...richin it a little and it wont sputter as much and it will pop up way easier....but its tuned pretty good....cant go wrong with rich tho man
if i were you and from my nitro expierience i would run just a liittle on the rich side so tune your HSN till theirs no more performance like lean it than back it off almost half a turn and dont really touch your LSNthanks
it's getting close, i would adjust first gear to shift about a second sooner at full throttle, it's idling at 1/4 to 1/8th rich, the low speed that is, the high speed needle sounds better but it's all about throttle response, if you have a thermal temp device, leaning out your needles while staying in the temp range is much easier, for a beginner you won't be able to get the full ability of the engine unless someone with more experience tunes it or you tune it with a thermal device.
you need to get rid of the deflector,it does rob power<< they are actualy used for tuning also, i put one on my 3.3 and tuned it and clocked it and lost quite a bit
It's not bad to shut i off that way short term... But if you're planning on letting is sit a day or two before you run it again you should pinch the fuel line and make sure there's no fuel in the engine.
@crusazul na bro.... i do that all the time... what happens is that it puts back pressure in the gas tank and richens up the mixture of the engine soo much that it will load upp with fuel... it wont hurt it!
When it stalled in the begging of the vid and started back up; the ex start had to be on the truck right? If so please show me where it is mounted bc I always wanted to have the ez start "wand" on the truck
its not a remote start, i did the same thing to mine, he cut the power and ground and hooked them into the battery box, you can start it as far as the controllor goes.
oh ok i see it now, but thats a lot of extra weight, i didnt say it right, if you cut ur reverse servo wires, and the power and ground wires from ur ez start and hook them to the cut servo wires and back into the battery box, when you hit reverse, it gives power to the servo therfor, starting your truck, mine is done like this but, i cant make a video, because my motor is gone right now
no problem, i will, im getting my 3.3 tomarrow, but i live in missouri so its cold, so i wont have any running videos, but i will do a video of the unboxing of the 3.3... and i will try to get a video up of the remote start when i get a new ez start, mine is old and worn out, so i have to buy a new one, im using a pull start right now, so if you want to, subscribe, you can see the 3.3 and the remote start, maybe sometime next month....
oh yea, about the battery, i have a hump pack (rechargable) if its used to start it about 10 times, it has a little effect but not much, so subscribe, and best of luck
its not a remote start, i did the same thing to mine, he cut the power and ground and hooked them into the battery box, you can start it as far as the controllor goes.
theyre fast AND durable. my slash has broken like........4 times in a year. and that is single parts. i broke an arm, two axle carriers, and my chassis. and the chassis was my fault not the slash's.... landing too rear heavy from like 40 ft high will break anything. thats brushless power for ya.
there the best handling trucks out there. and have lots of cool new inovations. but arnt as good for bashing stock compared to a stock HPI but there lots of fun to mod up. and can kick ass. if you look after them and upgrade parts that keep breaking there durable as fuck
now i have a tmaxx 3.3 and when ever i try to accelerate,, it just boggs down and then later on catches speen again. Now ive tooken it to the shop a couple times and they told me to try to run it lean and try to also run it rich... And ive di both and i see no improvement. I NEED HELP!!! I WANT FUN AGAIN!!!
lol cool. do u have any upgrades in it? i have like 500 bucks put into my t maxx 3.3 just in upgrades not broken part like upgrades most are preforomance.. lol i want to see ur truck it get some air.. cool video.. good tuning by the way :P
i don't understand u codybobo i want me to turn the high speed needle in all the way and then 2 turns out that will run it way lean wouldn't it ???? and quick question guys how far do u guys have the low speed needle set too and high speed needle i'm runing 20% Byron Original RACE fuel 20% i'm ruing some where around 250 degrees
well this is my other acount (its codybobo)they say you shouldnt mess around with the low speed needele and no it wouldnt its does fine in all my races
@berto123078 Thats not too hot but i would lean it out a tinybit to make it a little cooler and also you should use topfuel as it was made for the engine.
ok you should trust me cause ive been racing for 3 years put your fuel needle all the way in then two turns out not any more or it will run to lean and make it harder to start and you will plug it up TRUST ME !!
Whiteboy - It has an on-board electric start system. Pay more attention to the RC car/truck world and you wouldn't be so far behind, and you wouldn't have to ask stupid questions anymore...
thanks for the comment kinda new at nitro trucks i usualy fly nitro helis but i would like your advice more jungle fish right now temp wise i'm runing 220-230 the book says no more then 270 what do u recomend i do. my needles and set kinda right i guess it doesn't shut off or stall
you look like your good, just like in the manual just lean it to the point you get no more blue smoke, overheating, stalling, cutting out, poor acceleration etc.
go all the way in clockwise with the high speed needle, and come out 4 counterclockwise, but it sounds nice.you also want a good trail of smoke from the exhaust!!!!!!!!
its shifting way too early, but other then that nice vid dam i remember wen mine was like that ( i got the exact same one lol) but i broke mine in half D:
sounds good, run at 250 degrees on a 75 degree day, then check to see if it returns to idle the second you let off the throttle, that'll get you as close to perfect on the Lsn as you can get.
i think its running lean...richin it a little and it wont sputter as much and it will pop up way easier....but its tuned pretty good....cant go wrong with rich tho man
dustineng1 4 days ago
@Traxxas54 no its not
YellowDB 2 weeks ago
Very nice tune, sounds great! Can you make a tuning video please!?
vernage916 1 month ago
wow ! what carb tuning is that ? it's very important for me , please answer ..
thank you !
1234Pahima 1 month ago
full throttle hit brakes then turn it will do 360
SUPERJJMJ 1 month ago
nice conotroller spectrum ?
123456789bradley 1 month ago
@123456789bradley its the stock traxxas am system
YellowDB 2 weeks ago
you guys in pa?
redneckalex08 1 month ago
hey whats the blue thing on the exaust called? thanks
boatwake 1 month ago
vtec lol
Tupples1 1 month ago
hey bro' can the t-maxx 3.3 Reverse?
yuri5675 2 months ago
@yuri5675 there's a reverse module i thought?
thedutchgtaman 1 month ago
It say tmaxx fucking idiot
1suzukimotocross 2 months ago
revo or tmaxx?
MrEvolutionist 3 months ago
@MrEvolutionist you're the biggest idiot ever.
u2bwachr 2 months ago
@u2bwachr and ur a genius right?
MrEvolutionist 2 months ago
@MrEvolutionist At least i can read. sorry :)
u2bwachr 2 months ago
man, I LOVE NITRO :D
powerking230 3 months ago
i think the t maxx cost more then the kea and honda
biggRed188 3 months ago
dude i wanna buy it
traxxasmaster1000 3 months ago
how much does it cost
kristencoomer123 5 months ago
does your neighbours complain of the noise?
TheYakiyamaClan 6 months ago
@TheYakiyamaClan i dont think there is any one else home it looks like an estate were they test nukes to see the devestation :)
elliasprophet 6 months ago
man i love that remote start and good idea with the exhaust extention.
69dodgechargerrt1 6 months ago
wow dude sounds perfectly tuned
zanrath12345 7 months ago
lol - it's faster than that kia spehia and that honda accord
f3l0ny33 8 months ago
looks and sounds great i just got one myself.
facebiter 9 months ago
is it twin engine
abodeeabbas 9 months ago
@abodeeabbas no, just the stock 3.3ci
RFTAEC100 9 months ago
what state do you live in
xXcorvetteXx12 9 months ago
Is this in livingston farms lol
snipe82 9 months ago
Is this in livingston farms lol
snipe82 9 months ago
post more videos
duncan33984 10 months ago
Did u do the break in porcedure on that
Xeverything1 10 months ago
How much do thoes cost?
737mattman 11 months ago
Make more vids
TheRcworld101 11 months ago
if i were you and from my nitro expierience i would run just a liittle on the rich side so tune your HSN till theirs no more performance like lean it than back it off almost half a turn and dont really touch your LSNthanks
ch0l0sk8r 1 year ago
is that the 4908 model
pallmark1997 1 year ago
post more vidsss!
klx110rider95 1 year ago 2
Yeah your runnin a little lean
sik250r 1 year ago
hey nice vid.. i have a question... what are ur needle settings?
atvsarebeast 1 year ago
sounds a little lean an 8th turn should have it running like a beast
mosterjam2010 1 year ago
the REVO OF TATUCO69 IS VERY VERY BEST.
thiagodossantosfig 1 year ago
is that auto start?
stuntrunt3263 1 year ago
it has the reverse
michaeljacksonfan73 1 year ago
hay wats the settings on your engine can u tell me
firmclock 1 year ago
sick vid i have a tmax too
jasonromeoracer8 1 year ago
it's getting close, i would adjust first gear to shift about a second sooner at full throttle, it's idling at 1/4 to 1/8th rich, the low speed that is, the high speed needle sounds better but it's all about throttle response, if you have a thermal temp device, leaning out your needles while staying in the temp range is much easier, for a beginner you won't be able to get the full ability of the engine unless someone with more experience tunes it or you tune it with a thermal device.
jaroncyr 1 year ago
how much did it cost??
hondaboyz367 1 year ago
This has been flagged as spam show
nice vid 5/5 check out my bashing vid of the e revo
krissford100 1 year ago
seems like the high speed needle is alittle lean. no noticable smoke trail when it hits second gear.
999benhonda 1 year ago
dude what kind of camera u got???
MrJSU2010 1 year ago
to soon 2nd gear
PainApple96 1 year ago
is that an electric start ??
kc7wwy 1 year ago
whats better this or the revo 3,3 please reply i plan on getting one soon
RetroFingerboards 1 year ago
is that a remote start?
VentureClanGaming 1 year ago
It's shifting fine. That's what happens with a good tune.
Now you need a servo to pinch your fuel line. :)
tony4sarah 1 year ago
seems like it shifting to early
jaredmcclain 1 year ago
love my t-maxx 3.3!
ethula14 1 year ago
u need to tune down ur idle a bit
rvall004 1 year ago
does it have reverse?
flyboy83297 1 year ago
i think its running fine
nkriebel99 1 year ago
how does urs turn on auto
sMarcelo49 1 year ago
what all have you done to it because i have leaned mine out so much and it wont do a wheelie at all :/
ReturnScroll 1 year ago
can the wheels on the t-maxx turn without moving
traxxasman4life2010 1 year ago
The wheels on the t-maxx only turn when its not moving if its tuned wrong. Its got a clutch.
foellerd 1 year ago
you need to get rid of the deflector,it does rob power<< they are actualy used for tuning also, i put one on my 3.3 and tuned it and clocked it and lost quite a bit
wesDUKES 1 year ago
damn you gotta take it easy on the throttle thats how i broke my first clutch spring
guitarhero3rox97 1 year ago
that remote start is kool but its just another thing ro replace after a crash!!!
trenary100 1 year ago
im gonna buy one of these but ca any one tell me what i would have to do because is is 90% assembled thanx
charlos95 1 year ago
wat is that blue thing of the tail pipe
SuperSnoozie 1 year ago
its a deflector, and it deflects oil away from the chassis, body and the wheels and it reduces just a bit of the engine noise without stealing power
cleaner is better ;)
RFTAEC100 1 year ago
HOW DID YOU START THAT
kubotaboy123 1 year ago
THANKU VERY MUCH
crusazul 1 year ago
does anyone knows if i shutoof the engine froom tune pipe will damage the engine in my tmaxx:>>????
crusazul 1 year ago
@crusazul
It's not bad to shut i off that way short term... But if you're planning on letting is sit a day or two before you run it again you should pinch the fuel line and make sure there's no fuel in the engine.
astrong94 1 year ago
yeah because fuel still remains in the lines and the motor. get a slightly longer fuel line and put the shut off on the back side
SPHEN1987 1 year ago
@crusazul na bro.... i do that all the time... what happens is that it puts back pressure in the gas tank and richens up the mixture of the engine soo much that it will load upp with fuel... it wont hurt it!
BraydensGasMaxx 1 year ago
might wanna rich it up a tad, idle sounds i little low too, good lookin truck tho man.
nitronut028 1 year ago
its supposed to ba litttle bit smoke like how it is i say it might be right.
dirtshower250 1 year ago
my shockwave would owned your tmaxx .
traxxas549 2 years ago
Dude Ive got to know how you started your t-maxx like that
rednck09 2 years ago
When it stalled in the begging of the vid and started back up; the ex start had to be on the truck right? If so please show me where it is mounted bc I always wanted to have the ez start "wand" on the truck
dragracing3508 2 years ago
@dragracing3508 remote start.
RM250D8rzr 2 years ago
its not a remote start, i did the same thing to mine, he cut the power and ground and hooked them into the battery box, you can start it as far as the controllor goes.
MRimports4life 2 years ago
yes it is a remote start. and what you were saying does not make sense. look at his other vids. its remote start.
RM250D8rzr 2 years ago
oh ok i see it now, but thats a lot of extra weight, i didnt say it right, if you cut ur reverse servo wires, and the power and ground wires from ur ez start and hook them to the cut servo wires and back into the battery box, when you hit reverse, it gives power to the servo therfor, starting your truck, mine is done like this but, i cant make a video, because my motor is gone right now
MRimports4life 2 years ago
ya i agree it is way too much unbalanced weight...
BraydensGasMaxx 2 years ago
its a good idea tho, but the way i did it is better
MRimports4life 2 years ago
@MRimports4life yeah. and hey that sounds cool. for sure make a vid! sounds like a cool little idea. must rob ur battery power tho?
RM250D8rzr 2 years ago
no problem, i will, im getting my 3.3 tomarrow, but i live in missouri so its cold, so i wont have any running videos, but i will do a video of the unboxing of the 3.3... and i will try to get a video up of the remote start when i get a new ez start, mine is old and worn out, so i have to buy a new one, im using a pull start right now, so if you want to, subscribe, you can see the 3.3 and the remote start, maybe sometime next month....
MRimports4life 2 years ago
oh yea, about the battery, i have a hump pack (rechargable) if its used to start it about 10 times, it has a little effect but not much, so subscribe, and best of luck
MRimports4life 2 years ago
its not a remote start, i did the same thing to mine, he cut the power and ground and hooked them into the battery box, you can start it as far as the controllor goes.
MRimports4life 2 years ago
i think the nedles are perfect
idiot881100 2 years ago
How did it start itself there was no hands touching it at all
futurepilot13 2 years ago
yes it's the 4908
berto123078 2 years ago
@berto123078 if its idling fine and running decent i wouldnt mess with it
green2stroke 1 year ago
@berto123078 is the newer one the 4907?
iPipe0 9 months ago
is this the 4908 version
burtonplanb 2 years ago
traxxes is fast but not durable right?
tell me if im wrong :P
gijsjeradijsje10 2 years ago
theyre fast AND durable. my slash has broken like........4 times in a year. and that is single parts. i broke an arm, two axle carriers, and my chassis. and the chassis was my fault not the slash's.... landing too rear heavy from like 40 ft high will break anything. thats brushless power for ya.
trxslashdriver 2 years ago
yes they are!
bduce77 2 years ago
there the best handling trucks out there. and have lots of cool new inovations. but arnt as good for bashing stock compared to a stock HPI but there lots of fun to mod up. and can kick ass. if you look after them and upgrade parts that keep breaking there durable as fuck
RM250D8rzr 2 years ago
@gijsjeradijsje10
they are very durable and fast. look at mine. Tmaxx 3.3 4908 jumping. i had to go really high to break it.
idiot881100 2 years ago
remote start wtf
msngros 2 years ago 14
please can any one tell me what do u udjust when you tune the tmaxs engine
the idle screw and the high speed needle only or also you have to move the low speed needle????
crusazul 2 years ago
This has been flagged as spam show
now i have a tmaxx 3.3 and when ever i try to accelerate,, it just boggs down and then later on catches speen again. Now ive tooken it to the shop a couple times and they told me to try to run it lean and try to also run it rich... And ive di both and i see no improvement. I NEED HELP!!! I WANT FUN AGAIN!!!
kbw029 2 years ago
raise the idle about 1/8 turn and the hsn 1/4 turn.
TRTC360 2 years ago
tuned perfect
Brian12Pearson12 2 years ago
thanku verymuch
crusazul 2 years ago
does any one knows what is the best engine temperature to keep on t max thanku
crusazul 2 years ago
260
adb140275 2 years ago
250-280
bduce77 2 years ago
dang that thing'll scat
derektrucksfan101 2 years ago
it looks a little lean you should get a heat gun and mak sure that thing isnt above 280 degrees
travtrav43 2 years ago
holy fucking shit u want make somefrys home slice really if it goes over 210wicth is 280 aprox fahreihight
TeamTraxxas37614 2 years ago
I think your jigh speed needle should be leaner and you should crank up the idle about 1/8 turn. great video!
bestfriendbikers 2 years ago
sounds like you have a good tune.
davidsrx793 2 years ago
lol cool. do u have any upgrades in it? i have like 500 bucks put into my t maxx 3.3 just in upgrades not broken part like upgrades most are preforomance.. lol i want to see ur truck it get some air.. cool video.. good tuning by the way :P
king14rk 2 years ago
high idle
yocatmeow14 2 years ago
Comment removed
sivalsin 2 years ago
cool auto starting
wildbanchee3 2 years ago
HE started it using a dffernt channel then having the ez start
TeamTraxxas37614 2 years ago
i don't understand u codybobo i want me to turn the high speed needle in all the way and then 2 turns out that will run it way lean wouldn't it ???? and quick question guys how far do u guys have the low speed needle set too and high speed needle i'm runing 20% Byron Original RACE fuel 20% i'm ruing some where around 250 degrees
berto123078 2 years ago
well this is my other acount (its codybobo)they say you shouldnt mess around with the low speed needele and no it wouldnt its does fine in all my races
savageracing101 2 years ago
@berto123078 Thats not too hot but i would lean it out a tinybit to make it a little cooler and also you should use topfuel as it was made for the engine.
WHOULOOKINAT123 1 year ago
@berto123078 ur running waaaaaaaaaaay too lean, you need to richen it out
ironmaidenkid455 1 year ago
ok you should trust me cause ive been racing for 3 years put your fuel needle all the way in then two turns out not any more or it will run to lean and make it harder to start and you will plug it up TRUST ME !!
codybobo101 2 years ago
you fail at english
adb140275 2 years ago
Nice lookin' T-Maxx ! Suunds like you need
to adjust the HSN and the 2-speed & actually probably the slipper clutch so that it shifts better/later and does not 'rev-up' so high.
taz1175 2 years ago
how did you start it in the beggin
whiteboy11000 2 years ago
Whiteboy - It has an on-board electric start system. Pay more attention to the RC car/truck world and you wouldn't be so far behind, and you wouldn't have to ask stupid questions anymore...
sbs9026 2 years ago
Ive been into rc cars and trucks for two years and never seen an auto start...
sivalsin 2 years ago
Alot of em have it... my buggy has it. (remote Start)
jjjmyers 2 years ago
all u need is a another channel
TeamTraxxas37614 2 years ago
thanks for the comment kinda new at nitro trucks i usualy fly nitro helis but i would like your advice more jungle fish right now temp wise i'm runing 220-230 the book says no more then 270 what do u recomend i do. my needles and set kinda right i guess it doesn't shut off or stall
berto123078 2 years ago
you look like your good, just like in the manual just lean it to the point you get no more blue smoke, overheating, stalling, cutting out, poor acceleration etc.
JungleFish 2 years ago
Comment removed
nenex1 2 years ago
your local hobby shop lol
JungleFish 2 years ago
go all the way in clockwise with the high speed needle, and come out 4 counterclockwise, but it sounds nice.you also want a good trail of smoke from the exhaust!!!!!!!!
nascarfanify 2 years ago
How in the hell did u start it??!! that was weird!!
eb4jimmy 2 years ago 5
does it have reverse i was watchin a video and it says it doesnt have reverse
etzkorn13 2 years ago
This model T-maxx does not have reverse (model 4908) but the older one (model 4909) does. :D
eb4jimmy 2 years ago
it has plastic but u can upgrade ofcourse and it runs like 15 to 17 mintues but give a few or take a few
berto123078 2 years ago
does tmaxx have steel driveshaft? or a plastic?
hondatmx 2 years ago
how long the runtime in fulltank?
hondatmx 2 years ago
its shifting way too early, but other then that nice vid dam i remember wen mine was like that ( i got the exact same one lol) but i broke mine in half D:
lulu1394 2 years ago
how the fuck??
bayouboy94 2 years ago
that was at eh begginning wen i posted that sorry =/
lulu1394 2 years ago
Nice.I have a 2.5 with 3.3 install,still can,t get it to wheelie yet.check my vids.
Vmackin 2 years ago
sounds good, run at 250 degrees on a 75 degree day, then check to see if it returns to idle the second you let off the throttle, that'll get you as close to perfect on the Lsn as you can get.
mstreamer9991 2 years ago
how did you start it? that was cool
mstreamer9991 2 years ago
richen hsn and do the pinch test for the lsn.
traxxassmaxx14 2 years ago