RESONANCE EFFECTS FOR EVERYONE TO SHARE test 1

[kdkinen]

awesome video buddy, great work

[gotoluc]

@kdkinen Thank for looking and posting your positive comment

Luc

[kdkinen]

@gotoluc

your welcome :) hey i have a question, if you can?

I am working with resonance as well in my vids, and im wondering about the series or parallel rlc circuit, which is best for wireless transfer/tesla coil induction, and why? :)

[gotoluc]

@kdkinen, I liked working with Series RLC but I don't know enough to explain why one is better then the other.

All the best in your experiments

Luc

[Riskteven]

So this is how to produce pure sine waves with LC networks?

[ilav1m8y]

This is a photo of the original Stanley Meyer software that I'd used to build my cell.

h t t p : / / w w w . m e g a u p l o a d . c o m / ? d = X O W 8 V K G Q

I'd share this with everyone but, I'd only cared about myself. You could copy Stanley Meyers equation if you want to and do your own calculation on your own!

John Myatt (Darwin, NT)

[ilav1m8y]

I'd used this same setup nearly 15 years ago and did a frequency sweep on a frequency generator to power a Stanley Meyer water fuel cell. I'd used the same information pack and Software that Stanley brought to New Zealand and shared with the Maori. The only difference is we'd used a charging choke at the outputs to the capacitor. Many thought that we'd resonated water molecules we'd actually resonated the space between the plates by calculating the capacitence/resonance of the cell to produce OU

[stivep1]

Thank You for Your very valuable explanation. You are of help to others in quest for Free Energy of Tesla as I'm

I'm showing what you have here in much different approach using

1.Vector Network Analyzer

2. Impedance Phase/Gain Analyzer

please compare by clicking at my nick name and search for

WOLNA ENERGIA PRZYGOTOWANIA I PROGRES video#12

[gotoluc]

@stivep1

Hi, thanks for you positive comments.

I have seen your videos before. I took a look at #12. Very impressive amount of equipment you have

Thanks for sharing your work

Luc

[greenwatts100]

Hay gotoluc can you run resonance 4 tutorial on a 1.5 volt AA battery nice work.

[ZED74]

just out of interest I read that you shouldnt short capacitors like that ,, better to put a load on it ,, If you have sometihng that can handle 500 volts lol ! You can end up with internal arcing and that can damage your nice big cap . You probably know this anyway since you know more about electronics than me ;)

[gotoluc]

Thanks ZED74 for your concern. I most always use a resistor but sometimes I need to do a show or limited of hands since one is holding the camera.

Luc

[faackoof]

@gotoluc What's the breakdown voltage of that cap?

[saintsnick]

continued... The Neon lamp glows with one lead because the ringing voltage is so high compared to the surrounding enviornment then even the open air dissapates energy from the other lead, illuminating the lamp. Your body absorbes more energy from the second lamp lead than the air would, to it illuminates brighter. The Ferrite core does also. Moving on to see your video 2!

[saintsnick]

continued... The HEAVY current draw occurs because the HV charge on the cap allows the coil to swing, in so doing, allows it to pull more current from the circuit. The Ground provides even more electrons to add into the ringing circuit as they are pulled in. Tesla knew this. He frequently watered his grouding rods for better conduction to ground.

[saintsnick]

continued... I bet the circuit charges quicker as the voltage gets higher and higher because as the cap voltage rises, it pulls less magnetic coupled energy from the transformer and is therefore "free" of heavy cap load and can ring more freely.

[saintsnick]

continued... The Diodes act as a half wave rectifier allowing the pulses to rectify into dc pulses. The circuit can only provide 3ma when shorted because the output coil can not free ring with a heavy load like a short. The free ringing with no short allows a resonant effect, allowing a resonant voltage rise. When the Big cap is connected, the cap charges up to the resonant voltage.

[saintsnick]

continued... So now, the primary side is ringing hard. The magnetic coupling to the second side is probably NOT resonant with the second coil, but you're vibratig it with some muscle for that little transformer. The secondary is swinging freely. It may have it's own resonant freq, which you're not hitting, but because it can ring free with each input pulse, it is is creating it's own ringing with each pulse.

[saintsnick]

Great video. No, this is NOT radiant energy, which IS a real phenomenon, but only emminates from a repeating undampened HV spark which is NOT what you have here. No, this is simple electromagnetic resonance, on several fronts.

For one, the primary cap and inductance resonate at 35.655hz if you do the math, but you were pretty close with the 28khz feed. Considering a loaded resonant circuit runs slightly off freq, you're probably hitting the sweet spot with that input freq.

[dodoshlodo]

you're creating radiant energy, it doesn't work like conventional electrons flowing around a circuit. that is why u can get it to light with only 1 wire.

Tesla would be proud ;)

check out my video "Shlodo's SSG Imhotep Radiant Oscillator" video on my channel

[dodoshlodo]

plug one side of the neon to your HV line and the other side to Earth Ground and see what happens!

[gotoluc]

Hi Drevtoobe,

thank you for all your help and information. I have a new setup and I'm now capable of measuring the current draw with good enough accuracy.

Also please note, you cannot post links in YouTube comment boxes no matter how hard you try since they don't allow it. That is what Forum are for.

Thanks for sharing

Luc

[ebisevac]

Can you tell us how did you calculate the values for capacitors and input frequency?

[gotoluc]

Hi ebisevac,

I did no calculations and have very little electronic knowledge. I simply stayed with the same coil and tried different capacitance and did a frequency sweep until I found the best reacting capacitance to charged the storage cap to the highest voltage while also keeping input miliamps as low as possible.

Luc

[MRH2O2]

@gotoluc

Please 'ignore' the Tesla Groupies, for the are wanderers in in a lost land and think Tesla was the second coming of Christ.

You have move entered the realm of of the strange and ignore the zealots.

Dr.S.

[gotoluc]

Hi bodziobran,

if I add a bulb in series on the Earth side the bulb will not light no matter how small the ma. I tried it with a diode and it has visible light.

I have posted a new updated video (test 2)

Luc

[bodziobran]

Congratulations of replicating Tesla radiant energy receiver.Please,put a tiny bulb (probably 75mA or lower) on wire coming from ground to check if this is an electron current flowing to fill capacitor negative terminal.

[gotoluc]

Hi centraflow,

thank you for posting your comment and suggestion. I will test your idea and get back to you with the findings.

Luc

[centraflow]

Nice work.Have you tryed connecting one leg of the cap to the primary of a transformer and the other leg of the primary to the disconnected leg of the diode and then measure the voltage of the secondary of the transformer. It will be interesting to see if it is a true ac or dc that is charging the cap.

[m3sca1]

good work

nice cap-where did you get it?

[gotoluc]

Hi m3sca1,

I won it on ebay for $15.

Luc

[m3sca1]

any idea what it is used for?

those standoffs make it look like something that used line power from the grid.

[gotoluc]

Hi tubemp777,

Thank you for looking and for directing me to Aromaz2012 video demo's. Very interesting work he is doing.

Luc

[crippled82]

Good work, try to find out the nature of the capcharge. Maybe it can deliver less energy than .5cv^2

[overunitydotcom]

Hi Luc,

What kind of ferrite transformer did you use ?

Maybe you can post a parts list in my

overunityDOTcom forum ?

Many thanks.

Regards, Stefan.

[gotoluc]

Hi Stefan,

thanks for looking at this new video. A new topic has been started at OverunityDOTcom. The link to the topic with a posted schematic is located in the description box next to the video. The part number on the transformer is hard to read.

I'll post what I find.

Luc

[overunitydotcom]

Luc, you could optimize this, if you would use a much bigger Ferrite transformer.

Then use a selfmade 9 Volts battery powered square oscillator and run the ferrite transformer at the resonance frequency of the primary LC circuit as you do it now.

Then the secondary is an Avramenko-Stiffler-plug. Then compare the cap energy storage versus input powerxtime= input energy

until the cap reaches 500 Volts.

[overunitydotcom]

Now you have to measure, how much energy

you can get out of the cap via some kind of

discharge circuit onto a load and how

much energy you need to charge up the cap via your circuit...

Regards, Stefan.

[overunitydotcom]

Very interesting Luc !

Seems you are verifying the experiments of Dr.Stiffer !

Curiously you really don´t get chocked without the cap... hmmm..

Pay attention with the 2 uF cap having 500 Volts can already be deadly, so better always wear gloves, if you experiment with these high voltage cap charges ! STay safe ! Many thanks. Regards, Stefan.

[najman100]

have you tried to hook up the system to a cell to see any effect .five stars .

[gotoluc]

Hi najman100,

thanks for looking. I did hook it up to a HHO cell and gas output was barely detectable but this was before I had the ground wire added. If you want to follow this a new topic was started at OverunityDOTcom. The link to the topic and where the schematic is posted is located in the description box next to the video.

Luc