ACME condor problems need help!!!

[minimeez1000]

Idle to low

[semion2003]

it's the high speed needle

[AymBro]

i work at a hobbie shop u have to tune ur remote aswell as rich and poor

[MonsterMaker3000]

i think you need to tune the engine or there is not enough fuel coming into the engine. hope that helps

[semion2003]

I have the same problem with my savegeXL

[nicholasstahtaris]

@semion2003 shit hapened dude :/ sometimes engines just fuck up no matter what you try and do. :/ its a expensive hobby what can i say..

[semion2003]

It's the needle

[aylamaree1]

i am having the same problem with mine i have checked everythink it started of the a crack in the fuel tank which wasnt pressurising the lines so i changed that and when i rev it for a bit it dies and then i have to put fuel down the carby and of it goes for another min. make sure all your fuel lines are clear take the air fliter of and take the tube that goes from your fuel tank and blow through the line and have a look down the carby see if u can see fuel comin through

[minileafe]

i think ur low speed needle is to rich

[MrStig17]

Right, what you do is take the air filter off so you reveal the the carboreta. Now open up the throttle and see if it opening up fully if not you need to adjust the triangle shaped cip closest to the engine with an alan key. Now you should be able to see the carb fully opening. Now restart it and it should work.

[nicholasstahtaris]

@MrStig17

probs would have worked back then but have a revo 3.3 check out my other vids!

[dobrien09]

Maybe its because you did not pull the pull start a fue times before putting in your glow start?

[nicholasstahtaris]

@dobrien09 naa not that

[RcHobbyFreak]

Try to lean out your low end and it will be okay :)

[nicholasstahtaris]

@RcHobbyFreak engine was blown not to worry

[TheSmyth18]

you need a failsafe it stops differant transmismisons from make it go and only your controller will controll it

[nicholasstahtaris]

@TheSmyth18 i no longer use this car and am uploading my new video of my revo

[xoDIRTBIKERox]

Hey guys i have the same car but when i start the car the wheels automaticly spin t like 40 mph so i have no controll over the car and i dont even hold down the trigger it just wont stop spining so can some one give me any ideas plz

[nicholasstahtaris]

@xoDIRTBIKERox

hi thanks for your comment, its most likely you have stick servos. these cars are cheap and shit i admit that mines sitting in the shed motorless and there for spare parts. it seems like your servo it stiking on full throttle and yeh. btw ill make a vid of my revo 3.3 next week sometime

[ChrisFay1996]

I reckon ur low end iis to rich lean it out or get a hpi acme are cheap

[nicholasstahtaris]

@ChrisFay1996 Hi

thanks for your comment im buying my revo 3.3 this weekend ive had a few cars since this one haha :P

but yeeh ill make a vid of that if i can be stuffed

[ChrisFay1996]

I reckon ur low end iis to rich lean it out

[nicholasstahtaris]

@ChrisFay1996 engine was blown

[lilmorris656]

you prolly just need to adjust the carborateur if its all the way closed it will turn off maybe if u start with the glowplug ingnitro just keep the glow plug on there till the engine gets warm

[nicholasstahtaris]

@lilmorris656 naa man that engine was fucked ahha

i got that car as spare parts now have a hsp trannasourous with team infinity 21 installed and about 100 australia off the revo 3.3 :)

[PS3firebirdfifty]

ive been having the same problem with my engine i was runnig mine and the engine blew, i dont have a fucking clue how it happend it was running for about 1 min it wasnt too lean cause i was no where near having it tuned in because i have used it about 7 times :L and i could hardly ever get it started anyway so overall i think the engine it completely shit mate and i am just going to buy a new engine for it.

[nicholasstahtaris]

@PS3firebirdfifty hi

thanks for your comment most likely holding full throttle for to long or your percentage of nitro is to high causing less lubrication to your engine. thanks :D

[pilot74sparki]

Hi, like he says, it could easily be your plug, but it could be your low speed needle? Maybee too rich or even too lean? Take back to stock, that's all the way out to flush with edges and start again screwing in clockwise 1/8th turn after each stall, you should notice engine idle increase slightly each time you do this

[nicholasstahtaris]

@pilot74sparki

hi :)

i did all of that but i think the engine is just ruined even alishanmao one of the rc blokes on youtube says that the engine is ruined so what i have done is ive bought myself a Team Infinity 21 engine :) that fits 1/10 scale so yeah thats what will be installed in about 2 weeks because im ordering it from japan.

thanks nicholasstahtaris.

[fatcobra93]

its your glow plug dude. notice how it starts to die after you remove the glow plug ignighter? its cause you got a bad glow plug. All u gotta do is buy a new glow plug and install it and it should run fine. And if you dont know how to do that well there are tons of videos of how to here on youtube.

[nicholasstahtaris]

@fatcobra93

yee thanks mate i know how to do that and my glow plug is new but it may need a bit of a clean up. ive tried flushing it to the edges and it was going but not very fast as it used to, so i didnt run in the engine and it lasted about 1 year b4 going like this. I didnt run it in because i was a noob 2 years ago i had no idea so ye but now i know what im doing n shit so yee thanks mate :)