I am so excited to try this, but I'm super nervous about it falling off with me on it! How much weight can it take? and how sturdy is when you do inverts and other advanced moves??
@Blackcatsimone Check out my other videos. I perform several inverts in a reply to this video. The key is to make sure you have some weight on the pole or slightly push down on it before committing your full weight to it; let the furniture grippers do the work. The weight on the pole is what causes them to grip, so in turn, do not try to walk in a circle around the pole while pulling your weight to the side. The bottom WILL slide out, knocking you off balance!
omg thanks for this vid!!! do u have any of u using it????? im seriously thinking about using ur instructions to make my own really soon!!! this is the best ive found with step by step instructions!!!!
@mrsnewbooty22 I would if I could, but I recently took it down to build a new one. This was built 2 years ago, so the plywood and lazy susan needs to be replaced. I'll put up a video as soon as I get the parts to repair it.
Do u mind putting it apart then rebuilding it back together so the people, like myself that have no clue what ure talking about, can get more of a visual idea? Please please please
hi there, i am trying to make something similar, i understand how you have done the bottom with the lazy susan and screwed the pipe into a flange. i am just not sure on the top it looks like you have screwed a bigger pipe into the flange and just slid your dance pole into that??? if so would that not make it a bit loose and wriggly at the top?? do you have anymore pics or anything you can show me close ups of the top part??? thanks
Im sure you have been asked this many time but there are too many comment to back track! I bought a Hustler Pro Gold pole in Feb 2011 and the spring broke :( What all do I need to make it into a spinning pole and bolt it together without the springe inside! The spring that make it tight into place is what broke. Ceiling is 10 inch high and the pole weith when hand grip is (50mm) which I think is 2 inch!
@TheBobbieRamones Yes, they do make special stud finders for the ceiling and I would suggest using one. They're meant to detect studs through the thicker ceiling. A regular one will rarely find a stud in a ceiling.
So I finally finished my pole..spent more for my own touches...the only problem is I painted it pink and put clear coat on it...but its too slipperly to hang upside down on :( do you have any suggestions for paint to get a a "stickier grip"...Thanks
@scheyenne87 I just used clear laquer in a spray paint can. It has been working perfectly for me, but sometimes it can be a little too sticky (twisted skin on the inside of your thighs sucks).
I made this pole in my house and it turned out great! I have vaulted ceilings so I had some issues in trying to get it hooked up propperly, but ended up getting it figured out just fine and I have been loving it! I do wish I could firgure out how to get it to spin a bit more evenly, and I think I need to put more lacquer to get a better grip, but it is definitly worth the $50 and way better then any pole that you could buy for even double the price. Thank you so much for this information!
@LuvMyTrevors I'm so glad that you were able to get it working! When you say you want it to spin more evenly, are the bearings not quite as fluid as you'd like, or does it feel wobbly?
@tigerpolekitten Yea, it sometimes feels like it gets "stuck" at some points durring my spin. I don't expect it to spin super fast or anything, but if I could get it to just flow smoothly, it would be awsome. But overall I am very happy with it. Thanks again!
I built this, however the lazy susan bearings SUCK. It looks like I need some higher quality thrust or radial bearings, does anyone know a good source for these? someone said auto junkyard but would have no idea what exactly to ask for...
so I can screw the top flange directing into my ceilingg and just use the bottom plywood, lazysusan, and flange for the spinning..also could I use another time of pole instead of the conduit like brass or something??
@scheyenne87 Sure, you could use any kind of material your heart desires. :) However, you might want to look into the proper fittings for these types of poles, and you may not even need certain fittings... like the nipple, because you can thread brass without it compromising the strength of the pole. Brass is pretty pricey though. Just research, then adapt your fittings and tools where necessary. Good luck!
i made serveral. i made 1 4 myself & my friends wanted me to do 1 for them. however, there is an easier way & everything will be removable & u can put it anywhere. but that was a good idea. good work.
@soocrispy89 Nope, but its held in place by the rubber grippers on the bottom of the plywood. To easily explain it, the grippers do their job when weight is applied. If there's no weight on the pole, it is moved fairly easily.
i just moved in to a new apartment and was thinking of buying a pole at my local spencers but my boyfriend likes building things and this will give him a nice project. Thank you. But seeing as how it is a new apartment, you said that the top piece isnt removable. do you mean that once i put it up that if we ever move we wpnt be able to take it down? just so you know i have never attempted pole dancing or building anything so i have no clue!! thank you for the video though.
@maggieg1990ify I apologize for not being too clear on that one... The top is definitely removable, but I wouldn't suggest taking the bolts out of the ceiling until you're ready to move the whole thing to a different beam in the house or in another house entirely. When you remove bolts/screws and then try to put them back into the same holes, the support weakens and can be a safety issue. Best of luck and post videos when you get it built! :)
ever have any issues with stepping on or stubbing your toe on the bottom boards? do you think it would work if you bought a large piece of wood or plastic to stand on, cut a hole big enough for the pole to go through and place the lazy suzan under that with another smaller board under it? that way everything is under your dancing surface.
This is awesome I want to build one for my anniversary next month. It looks simple enough but I wanted to know what size bolts do you suggest for the top. Also what brand of finish did you use and what kind of sander did you use...oh and can I use a large piece of plywood under the lazy susan instead of the small square?...btw I have never built anything in my life
@jennettie The bolt size will vary depending on the size of the holes in the flange - just make sure the head of the bolt is large enough to not slip through the hole. I just used a fine grade sandpaper and did it manually. The finish is just clear laquer. You could absolutely use a large piece of plywood. I moved and ended up putting pergo flooring under it.
That's for posting this! One question-> How do you make sure the bottom doesn't slide out from under you as you're spinning, etc.? The wood isn't bolted down, right? So what makes it sturdy? Thanks!
This really is a great idea especially if you can't afford to buy a proper one but tbh i think it looks a bit shabby, like its come from a scrap yard or something, just in my opinion i think for safety and for quality you should save up for a proper one! you really did do a good job though!
how does it hold up on carpet? i was looking at x-poles but they are like 300 dollars a pole so i was looking for something cheaper... but i don't want to break my neck because the pole slips. i do a lot of advanced pole tricks so i need something that can handle the wear and tear so to say lol...
Ignorance is no substitute for engineering or basic facts.
Which leads into your 'paranoia' comment:
1) I never used the word 'incompetent' - you did. (fwiw - I can see your not incompetent, but this is a safety issue so...)
2) There's nothing paranoid about reminding that the 'NSA is recording'. They are. It's legal. They store it all & have a file for each person. Not paranoia - Fact. Watch PBS Nova/Frontline doc 'Spy factory' at PBS wed site if you don't like to read. Remember Patriot Act?
@tigerpolekitten - you state in the video that it's 50. But that doesn't matter because you still don't understand the difference between 'shear' force (lateral) & the mfg's intended 'support' rating. U will have plenty of time to read up when your a quadriplegic. And - no - you would not rather have epidermal paint poisoning than metal shavings. What do I want for $50? - not $50k in medical. This is what I get for trying to help a w.t. stripper ? wow - Never try to teach a 'carny' to sing -
@NSAisrecording Shear force? Maybe... but I think you mean centrifugal force. Regardless of what you may think, I am by no means incompetent and have done my homework. No one is forcing you to build it and/or use it. I know for a fact that it is safe if built as instructed. I've been using it for over two years now. Per haps someone as paranoid as you (made obvious by your user name) should seek entertainment elsewhere. Maybe a UFO convention? Just a suggestion. Have a nice day!
lazy susan is rated @ 50lb support weight not lateral shear force.
bolting a 2x4 (2 ft long) flat along the ceiling stud with a hole drilled in center would hold pole + let it spin + be cheaper + simpler.
Painting pole is bad idea - epidermal injection into pores of skin from sweat & abrasion + paint won't last.
Cheaper to spend on quality already chromed closet pole (big version) from cabinet supply & do it right the first time. U wasted much time building + buying paint and that adds up too.
@malear1982 sweetie..thanx for the info...as for the ass giving you shit about your correct"terms"...dude..she's a stripper..a chick..talking to other chicks..so back off...sheesh. thanx. i'm working on mine now.
does the bottom part ever come loose? and how do you get it to stay in place because i noticed in your other video you just tap the bottom part in place. and will the gripper really hold when im spinnig low preatty quickly?
@serafinyado The bottom has never come out from under me unless I was doing handstands. There has to be some weight on the pole in order to keep it in place. I spin quickly and low on it alot and have never had the problem.
i was wondering, have you ever had any problems with this? has it ever slipped out from underneath you when doing any spinning or where there is torque on it? i just don't want to end up with one of those embarrassing youtube vids of it failing. i saw your vid you posted dancing on it, i'm just wondering other than that. want to be sure before i do it.
Curious? Could you invert the pole you have built? Having the lazy susan pieces on the ceiling also making the bottom flange to be trimmed to look better? As well as it being better to lubricate the pole so it does run down? And possibly adding stationary pins through the pieces of plywood with the lazy susan between to make it a static pole? I've been researching dancing poles for a long time. As well as being experienced in the trade. But your video has inspired me to build my own pole. TY
@ScorpioQueen1078 if you do that, you'll have friction on the bottom that could easily cut a hole in your floor. you'd be essentially hanging from the ceiling. I wouldn't recommend using a lazy susan at the top.
i was just wondering???? so i measured my cealing and its 8 ft. 5 in. so do i get the pole 8 ft 5 in or do i minus the size of the ply wood or what???please get back at me...thanks
@panui subtract the size of the plywood and other materials. remember, don't cut too short. you can always trim more off if it's too long, but you can't get the length back once you cut it. :)
@TheMisslizabeth I wouldn't recommend that because the pole would be hanging from the ceiling with no steady base. I don't think the Lazy Susan could handle it.
@TYPSII83 Sure, you can attach the bottom piece of plywood to the stage and still make it spinning, but I wouldn't suggest using it. The plywood wouldn't make a very sturdy base and you'd have to make sure that everything is bolted together extremely well without a brace at the top.
highly suggest using some black tape around the bottom. you seem like an experienced dancer, how many times have you slammed your foot into the bottom? ive been dancing for 7 years :) good luck and SAVE YOUR MONEY! live poor because in 5 or so years you will have a huge amount of cash to invest :) good luck hon
There was another youtuber that built a stationary one. She just didn't include the lazy susan. I don't know of any way to lock it in place so that it can be used stationary or spinning.
I should have gone with a 2" and I did try, but Home Depot didn't have a 2" flange in stock when I was buying all of the hardware. Besides, 1 1/4" is much easier to grip than its larger 2" counterpart. :)
I need a home pole that will solidly handle 200lbs so u can get back to my 100 lbs frame I lost being bed ridden for4 years and most important my self esteem and self image?Very ashamed so any positive help very grateful for.
Congrats to you for wanting to get healthy again! The lazy susan is tested for 500 lbs, so it can definitely handle your weight. I wish you luck in achieving your goal!!
Probably so, but I didn't have $150 to buy one, so I got creative. :) Besides, I've heard bad stories about the Peekaboo poles... Something about they can't hold all your body weight and they cause injuries. I know that there are other brands out there, but you can't get them for $50! :)
@tigerpolekitten, Ya I guess you're right, if you look up stripper pole accidents in the search bar you get 100's of results abd they are of the store bought ones falling over while someone is on them. It's funny to watch, but not so funny if it happened to me haha :)
I'm not 100% sure on that one because I haven't built it that way, but you could probably just bolt the bottom flange to a piece of plywood, then bolt the plywood to the floor (without the lazy susan). However, if you want to make it removeable and 100% safe, I'm not really sur ehow to do that...
Can u give me a copy of the material list???? Also I'm wondering if the pole is not attached to the floor, is there no risk that the pole move. while you are dancing on it and you fall?
The material list is in the video description. The pole is NOT bolted to the floor in my case. However, I suggest you use good judgement as there is always the risk of being hurt.
is the bottom of the pole attached to the floor at all? Also, im having such a hard time trying to find a stud or whatever in the ceiling how did you do it?
No, the bottom is not bolted to the floor. You can bolt it down, but then it isn't removable. I found the stud in my ceiling by using a stud finder. You can purchase one from any hardware store (or even borrow one), but make sure you find one that can read through thick surfaces or says that its for ceilings or you'll get a false reading.
Hey Tiger, I followed your instructions and made my own pole. It works awesome!! Not hard to do. Thanks a lot.
I got all the materials from home depot and I have a list of parts and links of the ones I used. If anyone would like to see this list, let me know. I know it would have saved me a lot of time at the store.
Ouch those corners on the plywood look lethal. Esp. for those of us who do a lot of floor work and ride our spins to the floor. Can you cut the plywood on the bottom part into a circle instead?
You absolutely could, if that's what you're comfortable with. :) I probably would have done that as well if I had access to a saw... But, I do floor work and slide to the floor with no problem, you just have to be careful. I even heard from one poler that she taped cotton balls on the edges with duct tape if that gives you any ideas...
I think I will try this but it will cost a bit more cause I'm using stainless steel...how would you keep it from slipping on cement. maybe a wider base also was think of how to stop the pole from spinning for more stationary tricks.
I have a home Depot close to me and when I ask for a adapter they said what kind so can you tell me what section you got it in or how to explain it and thankyou for anwsering my last question
Its a piece of hardware that can be found at your local hardware dept. with the help of an employee. Basically, it is a set of ball bearings (that allow the pole to spin) sandwiched between two pieces of metal.
lol thanks. There's no static mode that I have been able to successfully make, however, nothing works better than trial and error. That's how this one was born... :)
HI, we are currently making our own stripper pole with your instructions and we were wondering if the bottom part will slip if we use it on hard wood flooring even if we use the furniture grips...also i am a litle heavier than you
It shouldn't, especially if you're heavier. The more weight, the better grip. However, please keep in mind, for your safety, that if you are going to pull on the pole in a side-to-side fashion at all, even if walking around it, that you must push down on the pole slightly to keep the grip. I recently moved mine to hardwood and have not had a problem as long as some weight remains on it constantly. Please test it with someone present just in case and start slowly. I don't want anyone hurt! :)
I sanded the pole, then used chrome spray paint. I laid the pole across a patio table with half hanging off, and painted half at a time. When the whole thing was dry, I finished it with clear laquer.
this is VERY creative...but i prefer my X Pole i think, its removable with no bolting, measuring, or plywood to scrap your foot on...but you cant beat the price i guess!! I would FOR SURE do this before wasting money on a peak-a-boo pole or something like that
It is not nailed down. What allows it to be removeable is that I have small, round, rubber chair grippers attached to the bottom. There are also sheets to skid proof material that you could place on the bottom - its used to line RV shelves or bathtubs.
is there a way to do it without the lazy susan....I have been dancing and doing tricks on a stationary pole for 16 yrs not a fan of the spinning pole :)
Yes, but it will not be removeable if you want it to be entirely safe. You can try it with the flange bolted to a piece of plywood, then attach grippers to the bottom, but I'd imagine that your weight will make it slip across the floor. You'd have to bolt it down.
hi well im really intresting on buying a stripper pole but i just cant afford it and i thought about the same idea too making my own pole so i thought it was awesome and if you can email me the list i would appreciate it thanks and that was a smart idea...
i wanna make a spinning pole since i use to teach how to stripp on a spinning pole..... can you send me a message that says how to build and what i will need for my pole? jenn btw my mysace is myspace. com/ sweetesweetestsin_8p
That's very impressive! I love innovative thinking. Is the pole about the same size as a 45mm?
kuruptm4a1 1 month ago
send me all the instructions to my email at alexandriabeach14@yahoo.com. thanks.
HanzoNagasaki 4 months ago
also, how does it compare to a 300 dollar x pole?
Blackcatsimone 5 months ago
I am so excited to try this, but I'm super nervous about it falling off with me on it! How much weight can it take? and how sturdy is when you do inverts and other advanced moves??
Blackcatsimone 5 months ago
@Blackcatsimone Check out my other videos. I perform several inverts in a reply to this video. The key is to make sure you have some weight on the pole or slightly push down on it before committing your full weight to it; let the furniture grippers do the work. The weight on the pole is what causes them to grip, so in turn, do not try to walk in a circle around the pole while pulling your weight to the side. The bottom WILL slide out, knocking you off balance!
tigerpolekitten 4 months ago
wow. what a great idea. a friend gave me a stationary and ive been tryin to figure out how to make it a spinner. Such a simple idea! Thanks a bunch!
laceydoll13 5 months ago
what are the furniture grippers for??
swampdonkey1122 5 months ago
@swampdonkey1122 When you put your weight on the pole, the grippers keep the bottom from slipping out from under you. :)
tigerpolekitten 4 months ago
omg thanks for this vid!!! do u have any of u using it????? im seriously thinking about using ur instructions to make my own really soon!!! this is the best ive found with step by step instructions!!!!
bellaricana 5 months ago
@bellaricana I do! Check out my other videos on my channel. :)
tigerpolekitten 5 months ago
Can u make a video of u putting it to gether for people that need help
mrsnewbooty22 5 months ago
@mrsnewbooty22 I would if I could, but I recently took it down to build a new one. This was built 2 years ago, so the plywood and lazy susan needs to be replaced. I'll put up a video as soon as I get the parts to repair it.
tigerpolekitten 5 months ago
How did you sand it? I just bought the pole today, please help!
OrgasmikGraphicz 5 months ago
having trouble getting my pole to spin? any advice!
reesesarah09 5 months ago
I am having trouble with my pole spinning. Any suggestions?
reesesarah09 5 months ago
you are brilliant. thank you no really thank you so much!!!
dize33264 6 months ago
how thick of a pole is proper? >.<
WoodGrainMayne 6 months ago
Do u mind putting it apart then rebuilding it back together so the people, like myself that have no clue what ure talking about, can get more of a visual idea? Please please please
KueenApostate 6 months ago
how thick of a pole /:
WoodGrainMayne 6 months ago
hi there, i am trying to make something similar, i understand how you have done the bottom with the lazy susan and screwed the pipe into a flange. i am just not sure on the top it looks like you have screwed a bigger pipe into the flange and just slid your dance pole into that??? if so would that not make it a bit loose and wriggly at the top?? do you have anymore pics or anything you can show me close ups of the top part??? thanks
hamishandkate 6 months ago
your such a champ lady! So solid and Fresh with some nice arcylic red paint on the base boards to think thats happening in my casa for sure
oxymoronick 6 months ago
Is there a way to make this pole without it spinning?
kennara 6 months ago
Im sure you have been asked this many time but there are too many comment to back track! I bought a Hustler Pro Gold pole in Feb 2011 and the spring broke :( What all do I need to make it into a spinning pole and bolt it together without the springe inside! The spring that make it tight into place is what broke. Ceiling is 10 inch high and the pole weith when hand grip is (50mm) which I think is 2 inch!
countrybaby81 7 months ago
OK so I didn´t go through all the pages to see if this has been asked before BUT
Can this handle inverts?
ultimateoctobot 8 months ago
is that a good size pole for someone with small hands or should i get a bigger pole im just starting to dance
NAEZbitches 8 months ago
is that a good size pole for someone with small hands
NAEZbitches 8 months ago
Is there any way to make a pole i bought into a spinning pole....just buy the lazy susan and flanges??
NICABOO750 9 months ago
@NICABOO750 I'm honestly not sure. I'd have to see your pole and try to come up with something to modify it.
tigerpolekitten 9 months ago
i kinda want to see the stripper thats too heavy for a 500 pound lazy suzanne
savageguy25 9 months ago
ive been begging my husband for an x-pole xpert!! I think I will do this instead!! do i need a stud finder for the ceiling?
TheBobbieRamones 9 months ago
@TheBobbieRamones Yes, they do make special stud finders for the ceiling and I would suggest using one. They're meant to detect studs through the thicker ceiling. A regular one will rarely find a stud in a ceiling.
tigerpolekitten 9 months ago
So I finally finished my pole..spent more for my own touches...the only problem is I painted it pink and put clear coat on it...but its too slipperly to hang upside down on :( do you have any suggestions for paint to get a a "stickier grip"...Thanks
scheyenne87 10 months ago
@scheyenne87 I just used clear laquer in a spray paint can. It has been working perfectly for me, but sometimes it can be a little too sticky (twisted skin on the inside of your thighs sucks).
tigerpolekitten 9 months ago
IS THERE ANY WAY TO USE A STORE BOUGHT STRIPPER POLE AND JUST BY FLANGES AND THINGS TO MAKE IT SPIN MY SELF..ITS A STATIONARY ONE???
NICABOO750 10 months ago
Genius! I wish I had found this video before I bought one a few weeks ago =/ I would've saved so much money!!
desiibabii3 10 months ago
I made this pole in my house and it turned out great! I have vaulted ceilings so I had some issues in trying to get it hooked up propperly, but ended up getting it figured out just fine and I have been loving it! I do wish I could firgure out how to get it to spin a bit more evenly, and I think I need to put more lacquer to get a better grip, but it is definitly worth the $50 and way better then any pole that you could buy for even double the price. Thank you so much for this information!
LuvMyTrevors 10 months ago
@LuvMyTrevors I'm so glad that you were able to get it working! When you say you want it to spin more evenly, are the bearings not quite as fluid as you'd like, or does it feel wobbly?
tigerpolekitten 10 months ago
@tigerpolekitten Yea, it sometimes feels like it gets "stuck" at some points durring my spin. I don't expect it to spin super fast or anything, but if I could get it to just flow smoothly, it would be awsome. But overall I am very happy with it. Thanks again!
LuvMyTrevors 10 months ago
@LuvMyTrevors WD-40 works WONDERS! That's how I got mine to loosen up. :) Happy poling!
tigerpolekitten 10 months ago
@tigerpolekitten
okay thanks darling, I will let u know how it goes!!
scheyenne87 11 months ago
I built this, however the lazy susan bearings SUCK. It looks like I need some higher quality thrust or radial bearings, does anyone know a good source for these? someone said auto junkyard but would have no idea what exactly to ask for...
Daegs 11 months ago
so I can screw the top flange directing into my ceilingg and just use the bottom plywood, lazysusan, and flange for the spinning..also could I use another time of pole instead of the conduit like brass or something??
scheyenne87 11 months ago
@scheyenne87 Sure, you could use any kind of material your heart desires. :) However, you might want to look into the proper fittings for these types of poles, and you may not even need certain fittings... like the nipple, because you can thread brass without it compromising the strength of the pole. Brass is pretty pricey though. Just research, then adapt your fittings and tools where necessary. Good luck!
tigerpolekitten 11 months ago
i made serveral. i made 1 4 myself & my friends wanted me to do 1 for them. however, there is an easier way & everything will be removable & u can put it anywhere. but that was a good idea. good work.
mrsllawson804 11 months ago
does the bottom part connect into the ground at all?
soocrispy89 1 year ago
@soocrispy89 Nope, but its held in place by the rubber grippers on the bottom of the plywood. To easily explain it, the grippers do their job when weight is applied. If there's no weight on the pole, it is moved fairly easily.
tigerpolekitten 11 months ago
i just moved in to a new apartment and was thinking of buying a pole at my local spencers but my boyfriend likes building things and this will give him a nice project. Thank you. But seeing as how it is a new apartment, you said that the top piece isnt removable. do you mean that once i put it up that if we ever move we wpnt be able to take it down? just so you know i have never attempted pole dancing or building anything so i have no clue!! thank you for the video though.
maggieg1990ify 1 year ago
@maggieg1990ify I apologize for not being too clear on that one... The top is definitely removable, but I wouldn't suggest taking the bolts out of the ceiling until you're ready to move the whole thing to a different beam in the house or in another house entirely. When you remove bolts/screws and then try to put them back into the same holes, the support weakens and can be a safety issue. Best of luck and post videos when you get it built! :)
tigerpolekitten 1 year ago
Learn how to sell yourself. Go hookers!
Wes306307 1 year ago
tigerpolekitten my msn in profile! Build Your Own Spinning, Removable Stripper Pole!
sexykatie911 1 year ago
Aren't you the money savvy one! I wish I saw this 3 days ago!
DreaTheHealthFreak 1 year ago
ever have any issues with stepping on or stubbing your toe on the bottom boards? do you think it would work if you bought a large piece of wood or plastic to stand on, cut a hole big enough for the pole to go through and place the lazy suzan under that with another smaller board under it? that way everything is under your dancing surface.
spazcatzrok 1 year ago
This is awesome I want to build one for my anniversary next month. It looks simple enough but I wanted to know what size bolts do you suggest for the top. Also what brand of finish did you use and what kind of sander did you use...oh and can I use a large piece of plywood under the lazy susan instead of the small square?...btw I have never built anything in my life
jennettie 1 year ago
@jennettie The bolt size will vary depending on the size of the holes in the flange - just make sure the head of the bolt is large enough to not slip through the hole. I just used a fine grade sandpaper and did it manually. The finish is just clear laquer. You could absolutely use a large piece of plywood. I moved and ended up putting pergo flooring under it.
tigerpolekitten 1 year ago
That's for posting this! One question-> How do you make sure the bottom doesn't slide out from under you as you're spinning, etc.? The wood isn't bolted down, right? So what makes it sturdy? Thanks!
FromSophiaWithLove 1 year ago
@FromSophiaWithLove There are rubber chair grippers on the bottom of the plywood. Applying weight to the pole keeps it from slipping.
tigerpolekitten 1 year ago
This really is a great idea especially if you can't afford to buy a proper one but tbh i think it looks a bit shabby, like its come from a scrap yard or something, just in my opinion i think for safety and for quality you should save up for a proper one! you really did do a good job though!
GaGaistic 1 year ago
how does it hold up on carpet? i was looking at x-poles but they are like 300 dollars a pole so i was looking for something cheaper... but i don't want to break my neck because the pole slips. i do a lot of advanced pole tricks so i need something that can handle the wear and tear so to say lol...
banglbabe 1 year ago
@banglbabe It works perfect on carpet! Just make sure you put the rubber grippers on the bottom.
tigerpolekitten 1 year ago
Ignorance is no substitute for engineering or basic facts.
Which leads into your 'paranoia' comment:
1) I never used the word 'incompetent' - you did. (fwiw - I can see your not incompetent, but this is a safety issue so...)
2) There's nothing paranoid about reminding that the 'NSA is recording'. They are. It's legal. They store it all & have a file for each person. Not paranoia - Fact. Watch PBS Nova/Frontline doc 'Spy factory' at PBS wed site if you don't like to read. Remember Patriot Act?
NSAisrecording 1 year ago
can you do really advanced hard moves on the pole and also will it hurt my cilling because I rent a house and I don't want to hurt it
druecollins 1 year ago
@druecollins Check out my other videos. I have videos showing me using some advanced moves.
tigerpolekitten 1 year ago
@tigerpolekitten - you state in the video that it's 50. But that doesn't matter because you still don't understand the difference between 'shear' force (lateral) & the mfg's intended 'support' rating. U will have plenty of time to read up when your a quadriplegic. And - no - you would not rather have epidermal paint poisoning than metal shavings. What do I want for $50? - not $50k in medical. This is what I get for trying to help a w.t. stripper ? wow - Never try to teach a 'carny' to sing -
NSAisrecording 1 year ago
@NSAisrecording Shear force? Maybe... but I think you mean centrifugal force. Regardless of what you may think, I am by no means incompetent and have done my homework. No one is forcing you to build it and/or use it. I know for a fact that it is safe if built as instructed. I've been using it for over two years now. Per haps someone as paranoid as you (made obvious by your user name) should seek entertainment elsewhere. Maybe a UFO convention? Just a suggestion. Have a nice day!
tigerpolekitten 1 year ago 11
the stuff you put on the pole for better gripping what was it called? thanks
TheLiveLife4You 1 year ago
@TheLiveLife4You Laquer. :)
tigerpolekitten 1 year ago
@tigerpolekitten thanks so much i can't wait till im good as you on my pole
TheLiveLife4You 1 year ago
lazy susan is rated @ 50lb support weight not lateral shear force.
bolting a 2x4 (2 ft long) flat along the ceiling stud with a hole drilled in center would hold pole + let it spin + be cheaper + simpler.
Painting pole is bad idea - epidermal injection into pores of skin from sweat & abrasion + paint won't last.
Cheaper to spend on quality already chromed closet pole (big version) from cabinet supply & do it right the first time. U wasted much time building + buying paint and that adds up too.
NSAisrecording 1 year ago
@NSAisrecording First, the limit is 500 lbs, not 50. Go to the home depot website and search for "lazy susan." it clearly states 500 lbs.
Second, the 2x4 would probably work if you have the time and tools to drill a 2" hole in it. The metal flange and nipple was easier for me.
Thirdly, I'd rather paint than have metal shavings and burrs bury into my skin, hence the paint.
Lastly, what do you want for $50? lol
tigerpolekitten 1 year ago
can u send me the list of the supplies needed for the putting up the pole. sunshine25x3@yahoo.com and malear1982@live.com thanks!
malear1982 1 year ago
@malear1982 Please check out the video description.
tigerpolekitten 1 year ago
@malear1982 sweetie..thanx for the info...as for the ass giving you shit about your correct"terms"...dude..she's a stripper..a chick..talking to other chicks..so back off...sheesh. thanx. i'm working on mine now.
metaphiz 1 year ago
so how do you keep the bottom in place if its not bolted down?
serafinyado 1 year ago
@serafinyado I used rubber grippers that would normally go on the bottom of chair legs and lined the plywood under the flange with them.
tigerpolekitten 1 year ago
Can you use the metal caps you see on the regular poles instead of the wood?
VSPINK17 1 year ago
thanks for this video it was vey helpfull
sexichica1202 1 year ago
how do you know where the beam is?
angelaramphal 1 year ago
@angelaramphal Get a stud finder from the hardware store. Make sure its rated for ceilings. :)
tigerpolekitten 1 year ago
I would so pay u to make me one. Haha this video was so cool. Thank u for sharing! :)
Lety010208 1 year ago
LOL, I have that same bed.... It is Sqeekier than hell!
mytwinsandme 1 year ago
does the bottom part ever come loose? and how do you get it to stay in place because i noticed in your other video you just tap the bottom part in place. and will the gripper really hold when im spinnig low preatty quickly?
serafinyado 1 year ago
@serafinyado The bottom has never come out from under me unless I was doing handstands. There has to be some weight on the pole in order to keep it in place. I spin quickly and low on it alot and have never had the problem.
tigerpolekitten 1 year ago
you are really cool. thanks for sharing.
MsEdenNicoleMasters 1 year ago
i was wondering, have you ever had any problems with this? has it ever slipped out from underneath you when doing any spinning or where there is torque on it? i just don't want to end up with one of those embarrassing youtube vids of it failing. i saw your vid you posted dancing on it, i'm just wondering other than that. want to be sure before i do it.
mchlld42090 1 year ago
@mchlld42090 nope, never had a problem. :) just build it exactly as I have instructed and use common sense and all should work out fine.
tigerpolekitten 1 year ago
Can you please list the items you bought please?
vctaurus 1 year ago
@vctaurus see video description.
tigerpolekitten 1 year ago
is it possible to put two lazy susans, one on top and one on the bottom?
roach9818 1 year ago
@roach9818 I would not recommend that simply because the pole will then be hanging from the ceiling with your weight on it. not good...
tigerpolekitten 1 year ago
Curious? Could you invert the pole you have built? Having the lazy susan pieces on the ceiling also making the bottom flange to be trimmed to look better? As well as it being better to lubricate the pole so it does run down? And possibly adding stationary pins through the pieces of plywood with the lazy susan between to make it a static pole? I've been researching dancing poles for a long time. As well as being experienced in the trade. But your video has inspired me to build my own pole. TY
ScorpioQueen1078 1 year ago
@ScorpioQueen1078 if you do that, you'll have friction on the bottom that could easily cut a hole in your floor. you'd be essentially hanging from the ceiling. I wouldn't recommend using a lazy susan at the top.
tigerpolekitten 1 year ago
can you please just send me an email with a list of everything i need to buy to do this. lol. I am not to good with this kind of stuff. thanks
TheCaseyalexander 1 year ago
@TheCaseyalexander see video description.
tigerpolekitten 1 year ago
how do i cut the conduit if my cealing is 8 ft 5 in do i minus the plywood (2.5in+2.5in=5inches) so do i cut it at 8 ft??
panui 1 year ago
i was just wondering???? so i measured my cealing and its 8 ft. 5 in. so do i get the pole 8 ft 5 in or do i minus the size of the ply wood or what???please get back at me...thanks
panui 1 year ago
@panui subtract the size of the plywood and other materials. remember, don't cut too short. you can always trim more off if it's too long, but you can't get the length back once you cut it. :)
tigerpolekitten 1 year ago
not-for-fat-chiks
TK4240 1 year ago
is it really safe ?
mem0o0 1 year ago
what can u do to not make it spin..?
eclipsetink53abc 1 year ago
@eclipsetink53abc Make it without the lazy susan and just bolt the flange to a piece of wood with grippers on the bottom. :)
tigerpolekitten 1 year ago
can you possibly pt the lazy susan at the top instead of the bottom?
TheMisslizabeth 1 year ago
@TheMisslizabeth I wouldn't recommend that because the pole would be hanging from the ceiling with no steady base. I don't think the Lazy Susan could handle it.
tigerpolekitten 1 year ago
Is this safe for full body weight?
cjay75217 1 year ago
@cjay75217 It's able to withstand 500 lbs. I also posted a video of me dancing on it to prove that it does work when built correctly.
tigerpolekitten 1 year ago
can u please send me an email of vide and a list of matriels i need to get because i was already thinking about getting a pole a spencers
ladyshort09 1 year ago
@ladyshort09 please see the video description. The list is posted there.
tigerpolekitten 1 year ago
next time you do this you should consider putting in washers under the bolts, (keeps the wood from splitting)
marshamarsha45 1 year ago
Hey, if you wanted 2 attach it 2 a stage, could you do that? And still make it a spinning pole? That's real neat btw :)
TYPSII83 1 year ago
@TYPSII83 Sure, you can attach the bottom piece of plywood to the stage and still make it spinning, but I wouldn't suggest using it. The plywood wouldn't make a very sturdy base and you'd have to make sure that everything is bolted together extremely well without a brace at the top.
tigerpolekitten 1 year ago
hey has it ever fallen down or has the ceiling ever collapsed on you?? haha. just wondering cause i so want to make one now!!! haha. :)
luckygurl33433 1 year ago
@luckygurl33433 nope, that's never happened to me, but just use common sense. If something doesn't seem right with it, replace a part! :)
tigerpolekitten 1 year ago
highly suggest using some black tape around the bottom. you seem like an experienced dancer, how many times have you slammed your foot into the bottom? ive been dancing for 7 years :) good luck and SAVE YOUR MONEY! live poor because in 5 or so years you will have a huge amount of cash to invest :) good luck hon
MrFatAmericanGuy 1 year ago
Thanks for the tip, but I've never hit my foot into the bottom, surprisingly. Now watch... because I said that, I'm gonna break my toe tonight. LOL
tigerpolekitten 1 year ago
Can you lock it to stop from spinning?
missyking1 2 years ago
There was another youtuber that built a stationary one. She just didn't include the lazy susan. I don't know of any way to lock it in place so that it can be used stationary or spinning.
tigerpolekitten 1 year ago
Could a wider size pole be used? I noticed that you used a 1 1/4 size pole--why did'nt you go larger, say 1.5" or 2"-inch pole?? Thanks.
y2kdiva 2 years ago
I should have gone with a 2" and I did try, but Home Depot didn't have a 2" flange in stock when I was buying all of the hardware. Besides, 1 1/4" is much easier to grip than its larger 2" counterpart. :)
tigerpolekitten 2 years ago
is that safe lol neat work i want to make one =)
mademoiselleQtee 2 years ago
I need a home pole that will solidly handle 200lbs so u can get back to my 100 lbs frame I lost being bed ridden for4 years and most important my self esteem and self image?Very ashamed so any positive help very grateful for.
LoriliLee 2 years ago
Congrats to you for wanting to get healthy again! The lazy susan is tested for 500 lbs, so it can definitely handle your weight. I wish you luck in achieving your goal!!
tigerpolekitten 2 years ago
Will the pole fall or something? and how do you know if its secure?
steph5504 2 years ago
i'd quite like to see you using the pole:)
biglak 2 years ago
@biglak There is a vid up of me using it. :)
tigerpolekitten 1 year ago
Umm it's probably waaay easier just to buy one... and it will look better too...
Lexxieable 2 years ago
Probably so, but I didn't have $150 to buy one, so I got creative. :) Besides, I've heard bad stories about the Peekaboo poles... Something about they can't hold all your body weight and they cause injuries. I know that there are other brands out there, but you can't get them for $50! :)
tigerpolekitten 2 years ago
@tigerpolekitten, Ya I guess you're right, if you look up stripper pole accidents in the search bar you get 100's of results abd they are of the store bought ones falling over while someone is on them. It's funny to watch, but not so funny if it happened to me haha :)
Lexxieable 2 years ago
Hi, where do you buy the lazy susan spin attachment? Thanks
SuperBootySnatcher 2 years ago
I got mine from Home Depot. Ask a salesperson for a lazy susan and they should be able to help you.
tigerpolekitten 2 years ago
how do you make it so the pole doesnt spin...?
thnx!!!! gread vids!!
=D
AshliAndersen 2 years ago
I'm not 100% sure on that one because I haven't built it that way, but you could probably just bolt the bottom flange to a piece of plywood, then bolt the plywood to the floor (without the lazy susan). However, if you want to make it removeable and 100% safe, I'm not really sur ehow to do that...
tigerpolekitten 2 years ago
Can u give me a copy of the material list???? Also I'm wondering if the pole is not attached to the floor, is there no risk that the pole move. while you are dancing on it and you fall?
marcelita5 2 years ago
The material list is in the video description. The pole is NOT bolted to the floor in my case. However, I suggest you use good judgement as there is always the risk of being hurt.
tigerpolekitten 2 years ago
is the bottom of the pole attached to the floor at all? Also, im having such a hard time trying to find a stud or whatever in the ceiling how did you do it?
carri1310 2 years ago
No, the bottom is not bolted to the floor. You can bolt it down, but then it isn't removable. I found the stud in my ceiling by using a stud finder. You can purchase one from any hardware store (or even borrow one), but make sure you find one that can read through thick surfaces or says that its for ceilings or you'll get a false reading.
tigerpolekitten 2 years ago
i just wanted to knoe can i make his pole and bolt it into the ground and ceiling soo it wouldnt
missyenvious2 2 years ago
I'm so glad you were able to make it!! Next, you need to post a video of you on it. :) Oh, there is a parts list in the description...
tigerpolekitten 2 years ago
Hey Tiger, I followed your instructions and made my own pole. It works awesome!! Not hard to do. Thanks a lot.
I got all the materials from home depot and I have a list of parts and links of the ones I used. If anyone would like to see this list, let me know. I know it would have saved me a lot of time at the store.
xinark 2 years ago
Could I see the list of materials you used? I'm going to try to make this. Thanks!
Whit23ney 2 years ago
Hey I was wondering if you could maybe e-mail me a copy of the material list because my roomates and I are trying to make a stripper pole =)
sdsu224 2 years ago
the material list is simply the description for the video =)
noisydoll168 2 years ago
hey I was wondering if i could get a copy of the list that you made because my roomates and I are trying to make a stripper pole. thanks =)
sdsu224 2 years ago
ca u please show me ur material list?
I would love to build a spining pole!!
flavajane1 2 years ago
@xinark Hi there! If you still have a copy of that I would love to see it. In in the process of building one myself. Glad yours worked out!
jthomasbojin 1 year ago
Ouch those corners on the plywood look lethal. Esp. for those of us who do a lot of floor work and ride our spins to the floor. Can you cut the plywood on the bottom part into a circle instead?
DivineMovement 2 years ago
You absolutely could, if that's what you're comfortable with. :) I probably would have done that as well if I had access to a saw... But, I do floor work and slide to the floor with no problem, you just have to be careful. I even heard from one poler that she taped cotton balls on the edges with duct tape if that gives you any ideas...
tigerpolekitten 2 years ago
I think I will try this but it will cost a bit more cause I'm using stainless steel...how would you keep it from slipping on cement. maybe a wider base also was think of how to stop the pole from spinning for more stationary tricks.
quila1986 2 years ago
what is a nipple
sholafash 2 years ago
its the piece at the top that screws into the flange. The pole is inserted inside the nipple to help steady the pole.
tigerpolekitten 2 years ago
do you haft to put the laquer on it all the time for you to slide good?
sholafash 2 years ago
I have a home Depot close to me and when I ask for a adapter they said what kind so can you tell me what section you got it in or how to explain it and thankyou for anwsering my last question
sholafash 2 years ago
The adapter I was talking about is for the electrical conduit. Its used to give the conduit threads and tightens around the pole.
tigerpolekitten 2 years ago
what is a lazy susan and how much did you get it for
sholafash 2 years ago
Its a piece of hardware that can be found at your local hardware dept. with the help of an employee. Basically, it is a set of ball bearings (that allow the pole to spin) sandwiched between two pieces of metal.
tigerpolekitten 2 years ago
thankyou for answering my question that helped alot!!!!
sholafash 2 years ago
lol thanks. There's no static mode that I have been able to successfully make, however, nothing works better than trial and error. That's how this one was born... :)
tigerpolekitten 2 years ago
U ARE COOL
Superjayjay27 2 years ago
HI, we are currently making our own stripper pole with your instructions and we were wondering if the bottom part will slip if we use it on hard wood flooring even if we use the furniture grips...also i am a litle heavier than you
soadchick2006 2 years ago
It shouldn't, especially if you're heavier. The more weight, the better grip. However, please keep in mind, for your safety, that if you are going to pull on the pole in a side-to-side fashion at all, even if walking around it, that you must push down on the pole slightly to keep the grip. I recently moved mine to hardwood and have not had a problem as long as some weight remains on it constantly. Please test it with someone present just in case and start slowly. I don't want anyone hurt! :)
tigerpolekitten 2 years ago
What material did u use to the rurface? i did my diferen but i cannot get to thE top
sexy69sunrise 2 years ago
I sanded the pole, then used chrome spray paint. I laid the pole across a patio table with half hanging off, and painted half at a time. When the whole thing was dry, I finished it with clear laquer.
tigerpolekitten 2 years ago
What material did u use to the rurface? i did my diferen but i cannot get to thE top
sexy69sunrise 2 years ago
do all of the poles spin like that? the ones you buy I mean
sosioh 2 years ago
Nope, some are static and don't spin.
tigerpolekitten 2 years ago
this is VERY creative...but i prefer my X Pole i think, its removable with no bolting, measuring, or plywood to scrap your foot on...but you cant beat the price i guess!! I would FOR SURE do this before wasting money on a peak-a-boo pole or something like that
jillianolsen 2 years ago
Hey there! ive been looking to build one of these for a while, will it work the same on a garage floor as it does on the carpet for placing it?
shcole1011 2 years ago
Is the very bottom plywood nail down to the carpet or do you have something to prevent the skidding?
msvjuliet 2 years ago
It is not nailed down. What allows it to be removeable is that I have small, round, rubber chair grippers attached to the bottom. There are also sheets to skid proof material that you could place on the bottom - its used to line RV shelves or bathtubs.
tigerpolekitten 2 years ago
thanks for your info.... :)
terrilynn517 2 years ago
is there a way to do it without the lazy susan....I have been dancing and doing tricks on a stationary pole for 16 yrs not a fan of the spinning pole :)
terrilynn517 2 years ago
Yes, but it will not be removeable if you want it to be entirely safe. You can try it with the flange bolted to a piece of plywood, then attach grippers to the bottom, but I'd imagine that your weight will make it slip across the floor. You'd have to bolt it down.
tigerpolekitten 2 years ago
hi well im really intresting on buying a stripper pole but i just cant afford it and i thought about the same idea too making my own pole so i thought it was awesome and if you can email me the list i would appreciate it thanks and that was a smart idea...
mariana03sal 2 years ago
Please see the description of the video. The entire list is posted there. :)
tigerpolekitten 2 years ago
nipple, lol
weekendWwarrior 2 years ago
thank you very much! I thought i become crazy to make spinning pole
tatarin54 2 years ago
I gotta give it to ya; that was ingenius!
cgrammeral 2 years ago 2
Can you email that list to me also?? Thanks!
dmoore9090 2 years ago
Check the description of the video. :)
tigerpolekitten 2 years ago
i wanna make a spinning pole since i use to teach how to stripp on a spinning pole..... can you send me a message that says how to build and what i will need for my pole? jenn btw my mysace is myspace. com/ sweetesweetestsin_8p
lotuslane21 2 years ago
what exactly did you use to sand your pole? how long did it take? and what did you paint it with?