Very nice lookin 2g bud. I take it you got the engine bay cleaned up and repainted? I want to get that done but not having a garage is quite the problem.
Thad be me..Where is it at..BTY? LOVE the clean engine bay..Trying to get that same look..Ill be hitting you up on ECMlink here shortly without a doubt. Just sucks my ETS kit was made for a GM MAF. Not a big problem though. Do you have their SD cable? Do you suggest I use the GM Maf for initial tune and startup and then swith over to SD? Does it take a bunch of calibrating?
Very..Very..nice ride man. Im neck deep in a build myself and am using the fp3065 as my turbo. Ive been debating selling it to get something bigger but after seeing this, I kinda want to keep it. Was it hard to get those numbers on pump? What type of head studs are you using? reg, or L19's? Im going to be shooting meth on 93 so Im hoping for about the same. Im going to be running 280's though. How is your fuel setup? Can you post your mods so i can compare. Thanks. Aweomse 2g btw. Love the idle.
I was dynoing on a uncorrected dynojet with about 93% humidity so numbers are a little low. I've got logs in the mid 600 wheel range which would be in line with what my turbo is putting out bout 65lbs/min. I've got the rest of the 2gb conversion minus the high wing, not a fan like the thumb nail spoiler better. Boost was at 37 for that horsepower. Thanks for the nice comments. Check out my dyno pull in my other vids.
@MercenaryX2 i have a pretty good knowledge of FP turbo's....I'm planning on running this turbo and mani setup...just wanted to know if he the max psi rating for this turbo. and a turbo is only gonna flow so much hot air until its not giving you any more benefit...just saying cuh.
Beautiful car...just needs rear 2gb bumper swap and high rise spoiler, and keep the 2ga side skirts as their not bad looking. I have a 96 gst and I think mines quick with just 270hp or so, Id love to take yours around the block with double my power haha. How much boost you running to get 560hp? Why isnt your torque curve higher than 440tq with 560hp? Just wondering...very nice tho, kept very clean!
Very nice lookin 2g bud. I take it you got the engine bay cleaned up and repainted? I want to get that done but not having a garage is quite the problem.
MercenaryX2 1 year ago
i really like your gauges..where did u get them at?? im looking for some for my 95 gsx
uncbearwr6 1 year ago
nice oil chap haha pretty creative...
EuRoWuRx4Me 1 year ago
Time to change your screen name :-P
littlerazcal1 1 year ago
Im trying to see that thing pull..Whats up? Maybe a little in car? 2-step? Something?LOL...
littlerazcal1 1 year ago
Thad be me..Where is it at..BTY? LOVE the clean engine bay..Trying to get that same look..Ill be hitting you up on ECMlink here shortly without a doubt. Just sucks my ETS kit was made for a GM MAF. Not a big problem though. Do you have their SD cable? Do you suggest I use the GM Maf for initial tune and startup and then swith over to SD? Does it take a bunch of calibrating?
littlerazcal1 1 year ago
bad ass gsx!
flyboyondeck 1 year ago
I'm injecting meth for this hp and L19's with out any dout.
Didn't I buy my jm fab fp heat shield? coating is the one fp use to offer.
405awhp 1 year ago
What did you coat your manifold with? Did you get it like that from FP when they were coating manifolds?
littlerazcal1 1 year ago
Very..Very..nice ride man. Im neck deep in a build myself and am using the fp3065 as my turbo. Ive been debating selling it to get something bigger but after seeing this, I kinda want to keep it. Was it hard to get those numbers on pump? What type of head studs are you using? reg, or L19's? Im going to be shooting meth on 93 so Im hoping for about the same. Im going to be running 280's though. How is your fuel setup? Can you post your mods so i can compare. Thanks. Aweomse 2g btw. Love the idle.
littlerazcal1 1 year ago
I was dynoing on a uncorrected dynojet with about 93% humidity so numbers are a little low. I've got logs in the mid 600 wheel range which would be in line with what my turbo is putting out bout 65lbs/min. I've got the rest of the 2gb conversion minus the high wing, not a fan like the thumb nail spoiler better. Boost was at 37 for that horsepower. Thanks for the nice comments. Check out my dyno pull in my other vids.
405awhp 1 year ago
@405awhp 37psi...whats the max psi for this turbo?? and how long have u been running that much boost and is the turbo still alive and kicking...haha
bigkat776 1 year ago
@bigkat776 37psi isn't shit for that turbo. You must not know anything about FP turbo's.
MercenaryX2 1 year ago
@MercenaryX2 i have a pretty good knowledge of FP turbo's....I'm planning on running this turbo and mani setup...just wanted to know if he the max psi rating for this turbo. and a turbo is only gonna flow so much hot air until its not giving you any more benefit...just saying cuh.
bigkat776 1 year ago
@bigkat776 touche sir.
MercenaryX2 1 year ago
Beautiful car...just needs rear 2gb bumper swap and high rise spoiler, and keep the 2ga side skirts as their not bad looking. I have a 96 gst and I think mines quick with just 270hp or so, Id love to take yours around the block with double my power haha. How much boost you running to get 560hp? Why isnt your torque curve higher than 440tq with 560hp? Just wondering...very nice tho, kept very clean!
TheElyk2005 1 year ago