those are some seriously low temps bro, well done! ive ordered the RS360 setup aswell. just curious as to what your room temp is? and what theremal compund/water coolant you used? cheers
@nuttertools888 This was in winter so my room temps are usually anywhere between 10-15c, in summer (now) I load around 70c in cinema 4d with the fans on max. I am redoing my loop again to add an RX240 in the bottom where the HDDs are and also adding my new 6970 into the loop. Thermal compound was the junk that came with the watercooling kit, I don't recommend using it haha my coolant is PrimoChill PC Pure Extreme ;)
@HAMBOY12345 Yeah I just cut out around where all the fans fit to make sure it gets good air flow. Where do you mean on the rear? internally it wouldn't fit because of the other rad but externally it will fit easily. Could probably fit a 120 in the drive bay if I had a different res.
@HAMBOY12345 Yeah I was going to put one there but rad hangs over the rear fan by like a cm. There is actually a few places that you could add another 120mm if you don't mind a bit of fabrication and modding. You could fit one down infront of the psu for example.
those are some seriously low temps bro, well done! ive ordered the RS360 setup aswell. just curious as to what your room temp is? and what theremal compund/water coolant you used? cheers
nuttertools888 2 months ago
@nuttertools888 This was in winter so my room temps are usually anywhere between 10-15c, in summer (now) I load around 70c in cinema 4d with the fans on max. I am redoing my loop again to add an RX240 in the bottom where the HDDs are and also adding my new 6970 into the loop. Thermal compound was the junk that came with the watercooling kit, I don't recommend using it haha my coolant is PrimoChill PC Pure Extreme ;)
samstar1412 2 months ago
Did you cut a hole for the third fan ?
looks like you can add another 3-4cm thick 120 rad on the rear.
HAMBOY12345 6 months ago
@HAMBOY12345 Yeah I just cut out around where all the fans fit to make sure it gets good air flow. Where do you mean on the rear? internally it wouldn't fit because of the other rad but externally it will fit easily. Could probably fit a 120 in the drive bay if I had a different res.
samstar1412 6 months ago
@samstar1412 Yeah the exhaust fan i mean. Looked at your build on the forums, looks like you can't. There goes that idea =( lol
HAMBOY12345 6 months ago
@HAMBOY12345 Yeah I was going to put one there but rad hangs over the rear fan by like a cm. There is actually a few places that you could add another 120mm if you don't mind a bit of fabrication and modding. You could fit one down infront of the psu for example.
samstar1412 6 months ago
@samstar1412 thanks for answering my questions been really helpful.
Just made my order on this Kit (pccg) so you won't be alone =D
HAMBOY12345 6 months ago
Comment removed
HAMBOY12345 6 months ago
cool bro..nice built..:)
ghepzsketchworx 7 months ago
@ghepzsketchworx Thanks mate, hopefully be re doing my watercooling soon so keep an eye out for that :)
samstar1412 7 months ago
that right there is a badass computer bro
jessyAKAthabasshead 7 months ago
@jessyAKAthabasshead Thanks man, its getting old but its still pretty good haha
samstar1412 7 months ago
@RWL2011 Haha thanks mate, its impossible to keep the thing clean!
samstar1412 7 months ago
kool
CripEastSide 7 months ago
@CripEastSide haha thanks buddy
samstar1412 7 months ago