Perendev magnet motor scheme

[VonBraun87545]

The Stator magnets in this 'Modified' Perendev motor are incorrectly placed, Stator magnets cannot be tilted back, must instead be 90* relative to curved edge they are attatched to and Rotor magnets must be at 30 to 45* relative to the moving disc's edge. This way, an instability is produced that causes a dedicated movement of the Rotor Disc in one direction. The more indivicual discs and frame magnet assemblies that are used the more the horsepower. The actual Perendev unit is certified.

[sausage4mash]

1) permanent magnets are NOT permanent when put under work 2) no system can give more than you put in 3) also herp derp

[aikaslbab]

Magnet motor or motor with more than 100 precent efficienty is possilble make. I say many times very simple example: If motor without magnets efficienty is very small about 40-60 precents, motor with magnets have efficienty big with about 65-85 precents. So if you make motor (say brushed) without magnets with 90 precents efficienty and what will be if you electro magnets replase with same power, force permanent magnets? Maybe when be efficienty 100 or 110 precents????

[VarykGerai]

@aikaslbab its not possible to get more than 100% efficiency.

[aikaslbab]

@VarykGerai

If brushed motor without magnets efficienty is let say 98 precents. In sides is electromagnets. What be if we put on place electromagnets neodinium or other magnet with same power? Do not thing that then be efficienty more than 100 precent, 110-130 precents?

[VarykGerai]

@aikaslbab its imposible to get the energy increase when converting electromagnetic into mechanical then back into electromagnetic

[VarykGerai]

@aikaslbab you will not get more than 100%, when converting electromagnetic energy into mechanical there will always be a loss. not to mention converting it back to electricity. Are you people realy that ignorant? Purpose of electric motor / electric generator is to convert mechanical/electromagnetic into another. Improvement to the device gets efficiency closer to 100% it will never go above that.

[aikaslbab]

"you will not get more than 100%, when converting electromagnetic energy into mechanical there will always be a loss. not to mention converting it back to electricity. Are you people realy that ignorant? "

Yes. Read my explanation why get.

[VarykGerai]

@aikaslbab yet so many years noone managed to do that.

[touchsmart0]

@VarykGerai and why not?

is 100% efficent putting x amount of power in and getting x amount of power out?

so if you put x in and get 2x out thats 200% efficient?

[AlbertLloydy]

Where's the magnetic shielding?

[aikaslbab]

@AlbertLloydy Nowhere. :)

[eloid777]

did you get a proto type made ? to work yet?

[aikaslbab]

@eloid777 I not build magnet motor and not see worjing in reality.

[11mdhon]

@aikaslbab この図面から見て物理的に政情にまわらない。

[eloid777]

no it will not work , for the following reason the pushing force is equal to the pulling foreces thus the forces cancel out, you need to have like poles repling and a arrgement that shiled and does not clog, you are arangement is wrong and alot of clogging effect

[superstitionadd]

@eloid777 The pushing force may well be equal in this one stator/disk assembly. But add 2 more disks at progressive half steps from the first and you're in business. the problem has always been the way the the magnet on the disk moves into alignment with the magnet on the stator, with a conventional like-like repulsion there is a point where it is fighting against coming into alignment. There is an arrangement that gets around this by creating a net propulsion in one revolution of the 3 disks.

[eloid777]

also your stator magnet have a incorrect angle set on them, the must be skewed

or almost parallet but abit skewed

[eloid777]

your magnet aragment noted as "right "will not work, your showing diametric magnets which will have the same push and pull forces equaled on the motor resulting in a clog effect... you need axial magnet on the stator.. the leading edge must be sheild on the stator.....thus the the force on the rotor will hav more pushing force to over the attaction force on the sheilded stators...

[aikaslbab]

@eloid777 It not my aragment. I get from one site. I bellive, that aragment is good and motor work.

[Aanthanur]

@aikaslbab no the motor does not work, it only worked to scamm people fr a while, now Mike is in jail :)

[VonBraun87545]

@Aanthanur

You are a lier my friend, the actual Perendev Magnetic Motor really does work. I'ver produced it, many other scientists world wide have reproduced it all successfully. You are ignorant, research for a few more years and maybe you'll be up to par.

[Aanthanur]

@VonBraun87545 yeah sure.... liar. thats why Mike Brady is in jail for 5 years and 9 months. he is the only one that was not able to present a working Perendec Magnetic motor. why did you not present our working model? or someone else that allegedly has suck a working model? You could have saved him from jail and his investors would be happy having such a magnetic motor.....

liar.

[Aanthanur]

@VonBraun87545 oh lol i see you also believe to be able to build an elextric space craft.

you are nuts.

[LiamXaoh]

@VonBraun87545 - the Perendev motor was a fraud and no one has reproduced a working version. Including you.

[aikaslbab]

This maybe not perpetum motor, it may after some period of time, maybe after some years lost magnet energy and not work. But if you want pay one time for 4 years (for example) for motor magnet and not pay every month, then this motor may be good for you.

[aikaslbab]

Stator magnets must be glued, I think, or restangle form to not rotate about it axis.