Nitro RC car with head lights and tail lights

[MrTurbomouth]

Question ????? I am trying to mount my LEDs light but the glue I first used started to eat my hand made paint body I did 2 days ago. What do I use to mount them ????? Without doing damage

[captaincommandu]

How did you wire it up and add a push button effect? Im trying to add lights to my crown vic rc.

[party5225]

Please tell me how you did that

[angelizquier1]

Its very simple. I didnt build the brains for this system. I got an old bicycle flashing tail light and took out the brain and leds and just changed two of them to blue and presto.

[driftsilvia16]

Can someone reply to this question: Is it necessary to put brackets for the lights? And then how do I get this brackets if needed?

[angelizquier1]

no brackets. I used hobby glue. Its clear so it wont affect the lighting and it turns kinda rubbery so they will stay on even with impacts.

[hybridownzDK]

did u make a hole to insert the lights or just put it under the body?

[giraffeswholovetacos]

wow thats pretty awesome i have an exceed rc dynamite with head and tail lights but no switch check it out.

[vmctowing]

how did u make it flash i really need to know

[angelizquier1]

Get a pulsating diode. You might find one at radio shack. If you solder all the led lights in a series circuit, it will make all of them flash. Thats the simple way to do it. The way I did it is more complicated because it has different modes. This requires an integrated circuit and advanced electronics knowledge.

[bpbduncan]

@vmctowing You could also buy flashing LEDs

[BLOOD1MONEY]

do you custom make these?

[bob4u1]

What size switch did you use and could you do the same with fog lights or not

[345ehsan]

if i wanna buy the supplies whats the name of each one so i can make my nissan 350z with lights

[angelizquier1]

you just need LED lights. Two blue and two red. You can use a regular switch or a button switch. You will need a separate battery source other than you cars battery. For my car, i used small 1.5volt watch batteries. It is a bit difficult to explain as this was completely custom made.

[karzygijose]

@345ehsan u can also get a 5v resitor 9v battery snap 9v or rechargeable and lnger wires and sloder and sloder iron and 4 leds any color for the front and red or yellow for the back

[romanw11100]

where did u get the supplies

nice car

[angelizquier1]

Its homemade from scrap electronics.

[ballhawk210]

ya wat if u buy a pack from a rc shop how wuld u instl that msg me bak and wat is the best 240 $ DRIFT CAR u can buy HPI E10 or something else

[29youngmoney]

iamhalam has a great video on how to put in head lights in a rc car

[MrYesmanII]

This is a little off topic but where did you get your rims and drift tire for your car? mine is also a 1/10 scale car, except its electric.

[inventionman103]

can u make a vid on how to wire it and put a switch in.........and where and how to get the blinking lights please......or atleast where u got everwthing i can go from there.......please

[Uttelito]

did you use any resistors (or waht they are called) or did you connect them directly to the battery?

[xXxSUBARUxXx2k10]

how do u put thm in????

[angelizquier1]

I kinda explain this on the comments below.

[rccarfreak1]

can u make a vid on how u put them on?

[justinpiu]

can you make a video how to do this?plz

[deloreangtr1]

awesome yo!

[jermainezey]

when the hit the switch on the back lights three time it look like a under cover cop car , u should do the same for the front

[vietkidd88]

Where did you get your switches ?

[angelizquier1]

you can get them anywhere. Radioshack carries a variety of switches. The ones I used came off some old toys.

[StreetFighterMoser]

go to radio shack and buy a momentery push button they have them in diff colors and sizes

[dogfacekiller1234567]

How did u do it I have hanted head and tail lights

[angelizquier1]

Well first off, you will need 4 LED,2 blue and 2 red all four 5mm. You will also need 2 switches or only one If you wish to wire only one battery pack. You simply wire your battery pack to the lights and thru the switch. Drill holes for the light to go through the car body and use hot glue to glue the LED's to the body. It is kinda difficult to explain because its custom made.

[dogfacekiller1234567]

K thanks I theank I now what your talking about

[dieharddirtbikerida]

what kind of bodyshell

[angelizquier1]

its an HPI toyota soarer

[Toki740]

nice ^_^

[Achevement]

thats sick

[meter124]

kooooooo

[jibjr88]

awesome