Setting up the Boss BCB-60 featuring Joshua Alo

[blackwidow88812]

do you put the tuner before the wah??

and do you plug it direclty into the jack input or the loop input

[MuthiX]

Muito legal xD vou comprar esse

[MrJETCITY]

Very, very helpful. Thank you.

[MichaelD8393]

the best signal path i've found is the following:

wah

tuner (optional)

overdrive & distortion

pitch shifter/octave either right after the wah or right after overdrive & distortion

equalizer

modulation (chorus, flange, phase etc)

delay

and finally reverb. and if possible all pedals from modulation to reverb in the amp's effects loop and the wah till octave/pitch shifter into the input. if no effects loop, just run everything straight into the amp's input. hope this helps

[alfreGr]

Great video man, thanks a lot! Now I think I'm gonna go with that pedalboard!

[kingmonster12]

the noise supressor goes last or first??

[gtodude17]

this looks almost exactly the same as a behringer pb600, so why double the price?

[sam7448]

I'm from the uk and i'm taking my bcb 60 over to the states this summer will i be able to use my uk power supply with an uk to /us plug adaptor or would i have to buy a new power supply while out there? if so what model?

[holmes1978]

Wish you would set mine up !

[godzilla964]

What kinds of wah pedals can use the bcb-60 power supply and plugs?

[RHCP1031]

@godzilla964 Just look if they have 18 volt because they wont work but i think the original GCB-95 crybaby will work.

[THECLAYSTER]

Did you change the smaller cables that connect the pedals or do they last pretty well? I just figure because companies usually send cheap cables, that these might be as well. Let me know, please reply, thanks.

[Jungleboy867]

can it power older boss pedals from the 80s that use an aca adapter?

[MindCrazedBanjo]

@Jungleboy867 I believe this board can only power 9VDC or 18VDC, the old ACA pedals are 12VDC so I don't think this board would be compatible with the ACA pedals.

[TheRolfieboy]

3:23... That's sexy, so clean and neat compared to the pedals just spread out on the floor.

[omegalen]

lol, fender 15 twin.... sorta thing.... haha xD

[adilghanty]

great video, nicely explained, thanks. 2 questions:

boss forgot to mention the all important internal dimensions - whats the maximum size (specifically length ie for wahs) pedal that will fit in?

and also you mentioned that its a 9v adaptor - what will this do to an 18v pedal?

thanks

[ramarazzz]

can the "ernie ball wah" fit in the bcb60???

[fattirevsbud]

Hey nice vid

I just bought it! I got the same vox Wha did you cut the npads or just removed them to fit the wah because the Top doesn't close with the wah on the pad, Im sure u had the same problem

keep rockin out!

[durarail]

I got a couple of pedals before my amp and a delay which needs to go through the fx loop of the amp . Does the BCB 60 have a send/return connection apart from the main input and out put ?

[seagreenyweeny]

Unflattering angle.

[yobhsiFehT]

Ugh, I had a Fender pedal tuner for a while, and it's got to be one of the WORST tuners out there:S

Nice video, tho. I almost wish I liked Boss pedals more so I could have a board that simple:D

[theoldmacarooni8]

The wah couldve fit if you used a phase 90 iinstead of phase 100 =D

[MrBeaverReviews]

After all that it didn't even fit!!!!

not the board I would recommend for someone with only 2 boss sized pedals (one of which is a power hungry giga delay!!!)

a pedaltrain/tone trunk or even a flatboard would have been better

[guitarmessiah95]

If i get this board how should I organize these pedals Boss NS-2,MXR 10 band EQ,Dunlop crybaby,Boss super chorus,MXR distortion +

[MrBeaverReviews]

@guitarmessiah95

don't buy this board with those pedals watch my review to see why

[LeonRussellisGod]

I was so inspoired by Johua Alo's dubby Jahwaiian skanky sound on this video that I bought a BCB 60, got a Phase 90 1974 Vintage Hand Wired in the place of the Phase 100,and a TW-1 Wah and of course the DD-20...now allI need to know is what settings were in place on the DD-20 at the time the video was shot?can you duplicate that sound?I am going to watch the video a few more times and see if I can figure it out,but lemme know da kine bruddah,da kine settings!

[mikolene97]

it comes with a power supply and everything??? sweeeeeett

[menga111]

aloha! love it

[austinmiller1996]

will i have room to put a digitich whammy on it

[domshar7]

if u did put the crybaby in, would u be able to close the case withit inside and can u cut your own sections out of the foam?

[bobklose]

Thank you Joshua:)

I bought an used BCB-60 pedalboard and the owner had cut off the foam to fit a double pedal. Do you know if is it possible to get a replacement foam? I've 5 single BOSS pedals

Bob from Italy

[arkinneas]

i just to ask if its posible to fit KORG VOLUME / WAH pedal at the rirght part.i am planning to buy that KORG product but i am not sure if it fits later on. can u please help me throw away all doubts.thanks...

[matmaury]

Hi, I've Just got This Pedalboard but it's impossible for me To put My 9V CryBaby.

Why ?

Thx

[TheRolfieboy]

@matmauray

Check if the crybaby uses center negative polarity. If not, you should stop trying, if not you will fry the system. (If the power was the problem)

[piemanzeppelin]

i have a Boss Super Overdrive, MXR Phase 90, Cry Baby wah, and digitech death metal distortion. does anyone have any suggestions on what order i should chain them in? i like the wah and overdrive to be beside each other. thanks

[easymusiccenter]

@piemanzeppelin a popular way to run those is guitar - wah -phase90 - overdrive - distortion.

or you could put the phase90 at the end instead for more of the effect.

[TheRolfieboy]

The drive or distortion are put before or after each other in the order of your liking. phase after overdrive/distortion, then wah (if you want a kirk hammet sound, put the wah before distortion).

So: Drive-Phase-Wah :)

[rodrigozamo]

I had a problem with my crybaby and he made the same mistake I did... he needs to take out the cushion under the wah to make it fit. otherwise it won't close

[01Justin010]

Does anyone know if this BCB-60 pedal board will power a Dunlop Crybaby Wah Original?

Thanks!

[EmmanuelGuitar]

yes the BCB-60 pedal board can power ur Crybaby, any pedal with 9v works, behinger pedals, boss pedals, cry babys, fender pedals, rocktron pedals

actually is very cool cuz u dont have buy baterrys or plugs anymore , and is case so u can close it when u dont need play

and ur welcome n__n

[01Justin010]

Thank you. The exact answer I was looking for. :)

[Baijidoom]

I notice it has two outputs. If I split my signal chain and send it into two different amps, would I still need an ABY pedal such as the Boss LS-2 in there? It would be very comvenient to pull two separate signals out of the actual box rather than from the pedals.

[ehartwell84]

Looks sick, im getting one for xmas :)

[01Justin010]

me2me2me2:D

[bondman00794]

me too

[magnussk8s]

i have a crybaby wah 9volts will it fit and can it be powered?

[MrSkeff]

yup it does, its not totally secure but its held in place by the cushiony foam bits

[thesoj]

Just use a Behringer PB1000.

They are made the same & fit Boss pedals.

The advantage is they're bigger (will hold 12 pedals) and you can get your big pedals in too.

Oh, and the power supply is better.

And they're cheaper than the Boss BCB60....

[01Justin010]

ORLY?

[Hellfighter77]

Behringer products are about as reliable as a paper condom. Steer clear of ALL their products if you don't want your gear to die within a few months. If you do go ahead, expect a nice long que to stand in for your Warranty as well. Comparing Behringer to Boss Products is comparing chalk and cheese. I have this BCB60 and it was worth every pennny. Very well thought out design.

[TheRolfieboy]

Please tell me if i'm wrong or right;

What comes with the pedal board is:

The board,

Jack cables (5 short and two long),

Power supply system (built-in),

Power cables (wall outlet-power system, power system-all the units in the board),

Interior padding

[EatenByAFrame]

That is correct. I just bought the board, it's great and works fine and can power all my pedals. Highly recommended.

[TheRolfieboy]

Is the output for a mixer or a amp? (low/high impedance)

[brusselleke]

ANYONE KNOWS it"s able to put a wah on the LEFT SIDE of this board?? 'Cause I control all my pedals with my left foot and it's easier for me with a wah on the left side...

grtz

[firegeek22]

y dont u just move over when u want to use ur wah?

[brusselleke]

Yes I know xD. just after I pressed Enter on this comment I thought it was easier if I just move over while using it ;)

Another Question (If you don't mind ;): I have a Crybaby and a 2-way switch of marshall. But i'm planning to buy an EHX Big Muff, a Boss BD-2 and a Boss TU-2. Do you think they fit all on the bcb-60? 'Cause the Big Muff is quite big and the wah two. (The Marshall switch is the same size of a Boss Twin Pedal ;))

Thx anyway. Grtz

[firegeek22]

haha nice.

[TheRolfieboy]

Do as firegeek22 says, put it outside of the pedalboard, or use your right foot.

[BBBNC5123]

Can you take all the foam pads out and put a big velcro peice down and then put all your velcroed pedals in?

[spratty59]

i had like 10 pedals for me, just had to buy a daisy chain for the extra pedals

[dagoblinray]

Im thinking of getting this but i dont see any velcro to hold pedals in place...if i set up my pedals in there and then throw this case in the gig trailer...will my pedals be all messed up once i open it again..does it really hold pedals in place?

[TheHorrorInside]

yes ! it does ! : D

just dont open it upside down, i do that all the time

[beantongue01307]

excuse me, does the cable that connects the effects to power supply included when you bought this? thanks

[guitarmessiah95]

does this thing come with the short patch cables to conncet each pedal and can this board fit a dunlop waj

[tankbrute6]

i dont get the output mono and return thing, whats that do??. and so the board comes with the cables and the cables that power the pedals?

[brusselleke]

Al the cables are included in the price ;) I'm planning to buy one too, seems perfect for me.

Grtz

[KG739]

i now know that this works for crybaby's aswell as boss pedals. my 1 concern is will it work for a dunlop mxr 6-band eq pedal?

[rbal4]

yes it will.

I have one in mine.

[Youngtothemax]

They way the board is setup at the last so with the fender effect and the orange thing will it still close?

Thanks

[easymusiccenter]

We had to turn the wah sideways to close it, but at least it all fit!

[Marguns]

@easymusiccenter Take that rupper thing on the floor out and any Whammy or Wha fits!!

[fattirevsbud]

@Marguns do you velcro the wah after takin off the pad?

[easymusiccenter]

I believe the ME50 is going to be too big to fit inside this board. the wall will probably fit, but i wouldn't recommend you leaving it in the case while you perform. the other pedals are no problem

[greendayfan19]

Could u please help me out ?!?

i have a Boss MT-2, Boss NS-2,

Boss ME50 and a Arctec APW-5.

Will this fit in this master piece ??

[OwensMusic1]

i hate these boards so i just built my own

[davidarkzero]

dreamtheater at the wall xD sytematic chaoss!!! /m/!!

[easymusiccenter]

nice catch! - chris

[kirkhamstter]

hey can i put a boss pw10 in a BCB30 pedalboard?(the small)

[GibsonLesPaul1319]

oh hell that looks fun setting up and arranging and plugging....sigh cant wait for mine!!!!!!!!!!

[bokma7]

hey great video! answers everything i wanted to know about this pedal board. =)

[BuffaloSinners]

how did you take the top off? its really lame if they dont make it removable, mine doesnt seem like it is.

[easymusiccenter]

I believe you have to open it all the way, and you'll see that the latches are open at a certain point and it will pull off. the cover should definitely come off.

[BuffaloSinners]

ya i totally had a blond moment i was messing around with it and realized it just pops off, thanks for being so cool about it though!

wicked walk through really helped!

[Alex43217]

so does it come with all the cables and everything?

[easymusiccenter]

Yes it comes with Power adapter and a special cable that can power up to 6 pedals. It also comes with patch cables! -Easy

[schnurr31]

why wont mine work =[

[Gnarlybenson]

106 pound

[MusicMasterJames]

How much does the boss bcb-60 cost, plese comment back soon really want to get one.

[NuggetMcSnuffball]

fredthefrog u can use any other pedal but it will take up more room but dont use morleys like the awsome dude said

[fredthefrog]

can anyone tell me...

can you only use boss pedals on this board?

I'm looking for a good pedal board and i have a boss looper, compressor and distortion. a marshall delay and reverb and a danelectro chorus.

will all of these fit in the board and be able to be powered by it? if not then can you recommend a better one?

[BuffaloSinners]

do you just use a daisy chain for the power?

[eman120730]

how much do these cost it looks awesome

[ErnieBallPlayer23]

ahh, going to have to get this pedalboard soon!

[kossumussu]

can u fit in 5 compact pedals and the boss pw-10

[mhd9890]

This thing is great! I JUST got it btw...and i can fit in 5 boss pedals + 1 twin pedal :DD

[Antony2191]

I like the SKB PS 45 and 55 you can use othe pedals rather than Boss although Boss makes good shit and I use thier Delay Tremolo and Tuner

[mhd9890]

hmmm should i get this OR i build my own pedal board?

[pedrowasabi]

If you have money go buy it! It's the best you can do

[mhd9890]

lol srsly? thx btw

[mhd9890]

will this fit a boss ev 5 exp pedal?

[pedrowasabi]

Yes, sure it will. It's a Boss pedal board, so it'll fit any Boss pedal for sure. And, as you can see in the video, he managed to fit a wha pedal, which is approximately the same size of your expression pedal.

[sourpips]

i gt faced with that dilemma but decided to just buy it has all the leads that match power supply built in should last longer then building ur own

[Roxastube]

Hey, Does this case fits for four compact BOSS pedals + Vox V847 + TU-15?

[tcrangle963]

and all the wires are included? u dont need to buy any hidden extras? think i might get one of these. my pedals have started to get out of control.

[ragw33d]

any ideas about the digitech whammy? doesn't look like it will fit not sure.

[easymusiccenter]

i don't think the whammy will sit in there nicely.... maybe just to transport...

[HarryRulesAll]

BEASTLY!!!!!!!!!!!!!!!!!!!!

[dennisvda1987]

Hey dude! I've got a DD6 pedal. I also 've got a TU-4(tuner) and a Cry baby Wahwah pedal. The DD6 is going in the Effect loops. How can I do this with the BCB-60?

[easymusiccenter]

i think the BCB-60 is meant mostly for pedals in front of the amp. there aren't extra inserts and outputs for the effects loop. so either they all go in the loop, or they all go in front.

you may be able to rig something using the 2 returns and 2 outputs (A for in front, B for loop), but you'd have to chain the appropriate pedals together as well.