Bedini pulse motor, build and diagram video 3 of 3. (TheDaftMan)

[lonslens]

Phenomenal. When I have time am going to research this material. Absolutely one of the neatest things have seen in quite a while.

[dalebednell]

Hi thanks for the inspiring video's i will give the the bedini pulse motor a go. I like the way you pinned it to a board so neet and tidy.



[bhaikhurram1]

hello dear sir,

u fine???

if i want to use more then one coil around we use same coil and its drive cct,s

[panyolito1929]

hello sir thedraftman . pls send me a circuit eletronic wiring diagram of badini machine ??? pls send to my email panyolito_1929@yahoo.com  thank sir

[itskaill]

will it still work if you run the coils separate from one another?

[mrmiles2011]

Another good video! When you are turning the 'shaft' controller, are you adjusting volts to Impulse coil?

In order to 'Supersize' this using bike wheel or auto brake rotors(more torque) for charging purposes. Do you recommend increasing coil size, more magnets or

additional coils around the perimeter or some combination of this? Which method is going to be most efficient? Thanks for info. and help.

[g4uonly69]

Hello, for this circuit, how long can you keep the charger battery hooked up. Will it overcharge either battery? Also, which battery do you use to draw energy from? Thanks.

[shartne]

Thanks for a explanation that i could understand. I wondered if i could run two coils parallel and four magnets directly across from each other using this same circuit. People are using these to desulfate batteries. Have you tried that yet?

[ghpiygfuy]

!!!!w w w diymagneticmotor com for FREE energy~~~

[MEMmaker3]

Excellent work - nice job and thanks.

[dadnak1]

Hell all

I have made all the three parts as mention by Daftman circuite.

i am little confuse on two parts i) the wheel is not spinning with primary battary only, i always need to connect to charge battary then only the wheel spins (i have connected two car battaries of 12 volts)

ii) Ny 110 volt bulb nver lights bright, it only shows very little when it gets two battary charge. as shown in vidieo the bulb lights very bright when we disconnect primary battry.

Please explain.

Javed-BAH

[100roberthenry]

i may be dafter than you, but if its putting out same as what its using, couldnt you flip a switch and have it run itself from its own output voltage.... :P

[kdkinen]

such nice work, even in the early days :)

[Th3mast3r69]

Is this motor supposed to be generating free energy or close to it? If so can you please give us another video with more details with the multimeter like amperes. I also would like to see the entire setup you have, batteries, caps if there are any etc. Thanks and great video. I'll be building one of my own soon!!!

[walkercreations]

What was it you used for the magnet spindle? I couldn't understand what you said in that part.

[leswhitehouse666]

These videos are excellent - immense help to someone like me who has never made a circuit before. My only question is with the magnets - the Bedini model states neo's should definitely not be used. Your rotor sems to spin nicely despite this though! Thanks for your efforts

[stenly83]

Thank you for your videos Daftman. They are so good, step-by-step with many details included. I want to build one of these things and I am collecting data for it but most of the other movies do not have much information.

[stenly83]

Thank you for your videos Daftman. They are so good, step-by-step with many details included. I want to build one of these things and I am collecting data for it but most of the other movies do not have much information.

[magnetman2010]

I asked you for more info' on the parts you used on your bedini motor. I found every thing I needed In your reclaiming parts video. I spend a lot of time looking at your videos. I have been learing a lot. Thanks much.

[magnetman2010]

I would like to build your bedini pulse motor very much but I can not read the diagram. I'm hoping You can show a clearer diagram and a printed parts list.

You do a great job, Thanks much.

[Lukeidea]

I'm sorry, if you dont mind, were wasn't you got the rotor.

It sounded like a "headrow" motor.

[johnrc1961]

How to squez more power out of this, if you put a thermoelectric plate inplace of the heat sink, you might get a bit of electricitu out of it.

Do not know how hot the transister gets, but it would be something to look into ?

[jeannacav]

Thanks for showing this method in these 3 videos so clearly. I have been using the slab of wood with the brass nails ever since I first saw this set of videos. It is great. Thanks

I already made jonny's no bearing one, but now it is time to make a real wheel. I came looking for ideas.

This is so clean and simple, I think I will use it...need to clear off the table- thanks so much

[pkrska]

Does it matter if I put 4 magnets on my spinning wheel or do I have to stick to 3 because of the firing of the transistor?

[Krazy4freeenergy]

Krazy4freeenergy; Hi there love the vids

step one made the circuit works

step two how do I connect slave coils to circuit and connect more than one bedini together and a million thanks to all you guys taking the time out of your lives to show us step by step instructions to a guy with NO electronic skill and I made one THANK YOU

[MediaStudioLabs]

We all know that the bedini motor is using more power than it's producing. The Mythbusters tested this motor once and it was a total failiure.I'm sorry for your wasted time.......Sorry for my bad english

[drunk2thepowerofsick]

its not wasted time. hes enjoying working on these and testing theories. go back to your tv

[MediaStudioLabs]

what's the reason to test something that you know for sure it will not work! the bedini motor is not a theory it is an unreachable goal

[octelcogopod]

The are no theories to test. "Free energy" violates several laws of thermodynamics. There is no such thing as "free" energy -- it has to come from somewhere.

[saturnx311]

Try building the effing thing before you shoot it down. What you were taught in school doesn't take into avccount the energy of magnetism, which is the same as light, or electricity-- just different wavelengths. Build it!

Then shoot it down after you prove it invalid.

[pkrska]

Mythbusters always do stuff without expert advise. Therefore they tend to miss crutial steps. Like building a rocket, without balancing it. Of course it tipps over!!!! I am sure Mythbusters missed a few steps doing the bedini. Or missed the point altogether.

[saturnx311]

Mythbusters is crap. OK? Crap. Those two pretentious idiots are just that-- out to prove things wrong in the guise of neutrality. I doubt if either one has had an original thought in his life.

They are wrong, wrong, wrong!

[leswhitehouse666]

@MediaStudioLabs Mythbusters attempt didn't work because the idiots left out the magnets! It should never have been shown on TV.

[khoham]

@leswhitehouse666

The mythbusters were trying A pulsed flywheel circuit,not the bedini monopole and since the mythbusters didn't disclose the circuit used it's construction is questionable.

[ehnriko]

Kudos!!! The world needs people like you. :-)

[mercofspeech]

Very pedagogic. Good for laymen as well as seasoned enthusiasts. Vvvvery skillfully done. Cheers!

[poorlesshobo]

your the reason i got into this kind of things. im trying to build a bendini pulse motor go kart. using a 20" flywheel and a total of 12 bobbins. If i were to use 22 gauge and 26 gauge wire on it would they melt?

[28MAXVOLTS]

Legend, thanks im a carpenter by trade but my hobby is this frre energy concept and you have simplified this circuit for me to build. the MDF and nails is genius for the DIYer. cheers

[scrawbag]

thanks a million for those

[freakman420]

inspiring, im building one with the same principals. just getting into electronics. finally getting though the extreme beginner basics. but its my calling. most informative video of the Bedini motor ive seen. thanks.

[theDaftman]

Thanks for taking the time to post your comment yours the DM.

[freakman420]

if you added a few extra coils wouldnt you get a greater output voltage?

[theDaftman]

Probably but this was just setout has an experiment for all to follow and make there own modifications like your suggestion.

Thanks for taking the time to post your comment yours the DM.

[belneste]

How would i wire up extra coils to the board? parallel to the first coil or in series with it?

[o0CLAUDIOeGIORGIA0o]

Well done great explaination...but a question....its possible to plug the exit voltage to the input pin in order to make the machine self runn????

Thanks!

[freakman420]

good question, im not sure but it sounds plausible. but if the output voltage is AC and the motor runs on DC then you would need a bridge rectifier to transform the AC to DC.

[carot2003]

Cheers, got diagram, started getting bits, great videos. Thanks again, will keep you updated. Cheers...

[BeefyCrackers12]

would a round piece of particle board make a good wheel for one of these?

[theDaftman]

Yes but please be certain you magnets are secure.

[BeefyCrackers12]

so the circuit picks up the magnet without a reed switch?

and can u have as many magnets as u want for one of these??

i have been getting the parts for this

[theDaftman]

1: No reed switch needed. See introvertebrate video (Understanding the Bedini Circuit) on youtube.

It will help you on the way.

2: can u have as many magnets as u want for this one? Yes.

Good look with your project.

[ifind2com]

You are the best, and I'd buy one from you if you wish. Contact me. :)

[theDaftman]

Sorry this one as now been scraped.

[image1951]

nice man i like ur set up

[BrainCrash001]

I have a really important question (at lease for me): Is it possible to run a bedini pulse motor from the output of another one? If not, why is that?

[theDaftman]

Running a Bedini pulse motor from the output of another one is possible

That's what my motor (Overunity Pulse Motor Bedini type 1) on youtube is doing.

Yours theDaftman

[s03w14]

Draftsman, I used your school girl diagram to build my circuit. I can not get the wheel to move. I traced the voltage and found that my emitter side have voltage but the collector side is zero voltage. (base has the same voltage as the emitter) But I think I may not be using a strong enough magnets have no idea the real strength of the magnets)to pulse the coil. Also the magnetis are 10mm diameter by 3mm glued on a razor scooter wheel. Do you think my size and strength of magnet is incorrect?

[theDaftman]

Sorry for my delay in replying.

I think this is one for the forum.

Please post you problems on the TEEP forum.

Teep(dot)i8(dot)com

Or please see link to the forum in description on the right of this video.

[Darkbain]

Wow,keep it up Daftman. There'll be a lot more experimenting because of you.

[jembalangmerah]

draftman,does the bedini circuit drain the energy from the primary battery or the circuit helps the two batteries charging each other??

[theDaftman]

The Bedini circuit drains the energy from the primary battery and then recharges the charge battery, well in theory that is.

[bratstarr]

cant believe that uve got the guts 2 thank us 4 wacthin......it is us mere mortals who owe u all the thx 4 ur time ur expertise & 4 giving us the hope that 1 day we 2 can say............ive bloody done it.

so plz mr daftman no more thanking us just tell us ur bidding & we shall comply.

keep up ur most excellent work...Brat

[theDaftman]

Thank you for your comments.

[maximusr2d2]

Your methods are very clever and artistic and i like the simplicity of it. Thanks so much for those 3 videos. So does this demo work to charge a 2nd battery to keep the motor running indefinitely if the batteries are rotated? Or is it just a highly efficient pulse motor?

[theDaftman]

Well in theory rotating the batteries the motor will run indefinitely. But don't let the batteries run down below 12 volts. (That's just a super quick guide)

[Griffith181]

theDaftman im not sure if someone already asked you this, but can I make that heat sink smaller? or is a 2inchX1inch (55mmX50mm)actually essential? I noticed you said it wasnt getting hot.

Im trying to make a mini circuit but the heat sink would have to shrink to a 1x0.5 sink. Do you think I will burn the circuit?

[theDaftman]

If you not running high currant it should be fine as long as it dont get hot.

[comwarrior69]

ok, if your running 12V with > 500 turn coils then you do not need a heat sink...

i'm running a PSU fan bedini and their is no heat produced using a 2SC4242 and i'm not using a heat sink...

[marthale7]

Thank you for sharing. Clean setup, I have gone to putting mine in a box.  I have had too many sparks because I crossed wires when I did not want to.

[theDaftman]

Thank you for your comments.