Sort by time | Sort by thread (beta)
Link to this comment:
Share to:
Loading...
- Your queue is empty. Add videos to your queue using this button:
or sign in to load a different list.
Loading...Saving...
Whats up all u free energy ppl! Bud I did everything u said but my coil hums a little is that normal. Also my neo magnets are way smaller than my core when I spin my rotor it comes to a stop what do you think is wrong
333kgb 9 months ago
@333kgb Hi,
I have not achieved free energy myself, but this circuit is great to desulfate batteries.
1.) check the value of your resistors with your meter may have too high a value, it will go into self oscillation and hum like you describe.
2 ) There are four possible ways to have the power coils, and trigger coils hooked up. Try fliping the two wires on the trigger coil, then test, then flip the wires on the power coil, as you might have the in correct connections there.
Peace
marthale7 9 months ago
This has been flagged as spam show
The negative on the primary battery go’s to the inner 20 gauge wire on the coil which also go’s to the emitter on the transistor and the inner 24 gauge wire from the coil go’s to the collator on the transistor then the neon bulb is connected to the emitter and collator does it matter which way I put the neon bulb? And is there any problems you see in this hookup? Thanks for you help!
333kgb 9 months ago
This has been flagged as spam show
The potentiometer is connected to a 24 gauge outside coil wire. My 1N4007 diode is connected to the positive on the secondary battery. Then the outside 20 gauge wire runs to negative on the secondary battery and on the positive on the primary battery.
333kgb 9 months ago
This has been flagged as spam show
Nice video! Hi I have been trying to get the bedini motor to work, but the wheel just comes to a stop. My setup is 1N4001 diode is connected on the emitter to the base on the transistor. Then the base is connected to a 470 resister. Then resister is connected to the potentiometer.
333kgb 9 months ago
This has been flagged as spam show
Free inexhaustible energy is real!But a few ppl make too many billions from our energy needs to let this technology be known,Find the real deal, a free energy device at LT-MAGNET-MOTORdotCOM ,Let the revolution begin!
slipshodcoqbgg 1 year ago
This has been flagged as spam show
Free Energy is real but the coverup is strong, if you are interested in a REAL free energy machine then
just search for the LT MAGNET MOTOR in the youtube video search , it is probably the ONLY working magnet
motor out there. Join the free energy revolution!!
urgencyharviefcem 1 year ago
were i can find the diagram ??
brickxcv 1 year ago
It should have a neon bulb to keep your circuit from overloading when u dont have your charge battery hooked up
dapop1001 3 years ago
You are so right, this was my 2nd Bedini that I built :) if you look at my earlier videos I know even less. :)
marthale7 3 years ago
Does the aluminum plate attached to the transistor serve a necessary function? My bedini SSg does not work and I'm trying to figure out why.
abb8279 4 years ago
confusing the base and emitter.. classic!
tvryb 4 years ago
yes :)
marthale7 4 years ago
It does not have to be there, I just put one in today. According to the sheet it says "Small 25 ma or bigger bulb can be left or removed here. Adjust 1k resistor pot so wheel spins fastest with ratio of lowest amp draw on primary battery.
marthale7 4 years ago
cool... When I turn my pot down too far it turns the motor off and I get that frequency noise. Do you get that?? When it gets to that point of shut down my voltage goes up to 40vdc. My first circuit it with the 5k pot and 22awg wire on both ends it shot up to 90vdc... some weird stuff is going on that is for sure. NICE SET UP by the way
ktservicescorp 4 years ago
Yes, I get the noise, but, not as bad as in your video, perhaps that could be because you do not have a core? I think you would be very interested in kubikop videos, as he had the same noise in his.
marthale7 4 years ago
Why didn't you put a light from resistor and why no neon bulb? Are these not neccessary?
ktservicescorp 4 years ago