Dboys fail (customer's gun)

[xCOWSRYUMMYx]

o yes the amazing dboys bearings...mine disintegrated on stock setup with a 9.6v

[Lassi1001]

I managed to use my D-boys Kac PDW 2months whit original bearings and ubraged to 31rps - 34rps whitaout eny proplems, =S

[maad416]

There are a lot of other tricky issues with the DBoys KAC PDW. One that I ran into is that the metal that the gearbox shell is made out of is prone to easily stripping screw hole threads. I stripped my motor screw holes, and with only 2 holes available, that means a new gearbox. I looked at a replacement DBoys M4 gearbox, which has the bolt release, but no compatible insets for the ambidextrous selector. My DBoys PDW is now on its way to becoming a VFC, replacement box coming from Taiwan. :/

[Maekiii]

@maad416 Lonex gearbox is 100% compatible with a kac pdw, and that's what I'm using.

[iWE4]

@maad416 I recommend using helicoil threadrepair sets. First you drill an 3mm hole with special helicoil drill. Then you re-thread it with M3.5 thread maker and finally you insert the helicoil thread repair patch. Outer diameter is 3.5mm and inner diameter is 3mm so you can use your original screws.

[maad416]

@iWE4 holy crap, thanks for the advice. Had no idea those existed.

[pmakiku]

In some point, all of dboys kac pdws came with these shitty bearings

[dsdehan44]

I have these spare in my 26rps stock JG g36c except for the DBoy bearing. I have noticed they are crappy but I want to see if they will last because I have nothing else.

[ungd1]

*Excited for next video*

[stefanits1234]

But hey this is in one piece !! :D I had at least 3 guns with grinded metal from the bearing inside the gearbox, and bearing pieces everywhere.

[stefanits1234]

Also, this is one reason why I strongly say "do not buy boyi m4 hk416, etcetcetc". Other is the crappy hopup chamber, bad air seal, weak motor, weak wiring.

[Maekiii]

@stefanits1234 Dboys guns are upgrading platforms to me, nothing else. Altough with little money and tuning you can make them pretty good stock weekend play aeg for quite cheap.

[ASoftaaja]

haha just tommoset oli tuossakin pdw:ssä minkä viritin ja yhdestä puuttui laakerin keskiö kokonaan.

[kalashnikob1]

Just like what happened to me... However I've noticed that the bearings in their v3 boxes are much more solid than in their v2 boxes.

[stefanits1234]

@kalashnikob1 That's because the v3s are in AKs and AKs are made by kalash, not boyi. Boyi makes M series, kalash makes AKs, dboys makes mags, and other accessories.

I had a LOT of these falling apart, however in aks they holds up fine...

[Maekiii]

@stefanits1234 Dboys and Kalash are the same. Same factory, same internals.

[Maekiii]

@kalashnikob1 My kac pdw came with proper ball bearings, they are actually not bad imo. This is completely different.. I dont think they even have balls inside them.

[Meboyboyboy]

ah.. 7mm bearings at their finest. maekii what do you run on your dsg? I personally use matrix 9mm ball bearing's, but my dsg is at 350 fps at 60 rps, and I've had to replace the bushings a lot recently. should I go to solid metal bushings? thanks!

[Maekiii]

@Meboyboyboy Definately go solid bushings, because there arent proper 9mm bearings on the market atleast yet.

[Meboyboyboy]

@Maekiii really? I mean matrix ones are working fine, but I'll go solid metal. thanks!