NetWelding
Loading...
Welding 4130 CrMoly
Welding 4130 Chrome Moly for race car chasses and roll cages requires carful choice of filler rod. Details of what to choose and why are presented...
NetWelding
uploaded
-
1 week ago
NetWelding
commented:
Tuning Holley Carb- Engineering A Street Rod.mp4
Tuning the Holley 850 Carb that comes with the Chevy 502/502 Crate Engine was a fun but often frustrating task. Ultimately had to replace with an ...
NetWelding
commented:
Edelbrock's a fine carb for a street only machine. For a real performance carb Holley is the way to go! In 1960 I had a Carter carb (Edelbrock copied) in my 1st street rod, a ’41 Ford Opera Coupe with a 50 Olds engine bored out an 1/8 inch. Modifed the metering rods! Similar to what I did wit...
Miller Plasma Cutter + Miller Fume Extractor + DIY DownDraft Cutting Table = Sweeeet
http://www.weldingtipsandtr...
The DownDraft plasma cutter table is finally done and it works like it is supp...
RENNtech Mercedes Benz C63 C74 AMG Drag Video 10.71 @ 132.91 mph - Road Test TV
http://www.RoadTestTV.com Drag Video of a RENNtech Modified C63. The C63 has prototype camshafts, race tune, ported heads, long tube headers, prot...
Mark Proctor and Paul Christian (Pop)
The Battle of the Dodge Colts, Burgundy Big Block Dodge Colt give the Purple Small block Dodge Colt the Back tire and the kick. Neither driver stag...
wildcat-Frank Huszar front engine dragster
original 1960s slingshot or front engine dragster a Frank Huszar and bob richy 392 hemi
Set MIG Gas Flow.mp4
Suggested MIG Shielding Gas Flow Rates. FREE technical paper available at www.NetWelding.com. This video defines why MIG gas flow must be limited t...
NetWelding
commented:
The two gauges read different things. The higher pressure cylinder contents(should be ~2000 psi when full.) The other is calibrated in CFH (cubic feet per hour) as you note. This flow is set by a very small orifice in the outlet (probably 0.020 to 0.025.) I estimate the pressure your setting ...
SIG 522: "Tactical .22 Done Right" by Nutnfancy
Imagine a Tactical .22 carbine that will feed pretty much whatever rounds you throw in it. If it seems far fetched then you must have some trigger...
NetWelding
liked
MIG_Welding_Gas_Flow_Settings.mp4
A FREE CHART is available at www.NetWelding.com that provides suggested MIG Welding Gas Flow Rates. Setting the proper MIG Welding shielding gas f...
NetWelding
uploaded
-
1 year ago
NetWelding
commented:
Excellent question asked by enginner who watched video. Long answer: see web page Flow Chart Page
Welding_GO-Green.mp4
Save About 1/2 Your MIG Shielding Gas Cost While "Going Green!" Each Industrial MIG Welder Wastes About 8 Tons of Carbon Dioxide or Argon/CO2 Shie...
NetWelding
commented:
@NetWelding: Thanks. It is interesting that fabricators can saveuo to 8 tons of CO2 MIG shielding gas per welder/per year and get improved quality weld starts and save a lot of money-but many do not understand the reasons for their high shielding gas use. Those using Argon based gases can save...
Welders Rap On Gas
Fun way to learn about the 70 to 80% waste of MIG shielding gas the average MIG welder experiences. The biggest reason is the "Blast of Gas" at eac...
NetWelding
uploaded
-
1 year ago
NetWelding
commented:
@6013welder For perspective, 60+% of all industrial welding is done with gas shielding MIG either solid wire or gas shielded flux cored wire. If welding out doors self shieldied cored wire and stick have the advantage of tollerating more wind.
-
1 year ago
NetWelding
liked
Why Gas Waste
Average MIG Welder Wastes 80+% of the Shielding Gas Used! This Video Tells Why and How to Stop the Waste and Improve Weld Start Quality.
FREE PDF ...
NetWelding
liked
Weld Math Deposition & Penetration Spread Sheet pds
Applying Math and Science in welding helps in understanding and solving welding problems.
A computer spread sheet can be used to calculate wire dep...
NetWelding
uploaded
Welding Math Deposition & Penetration Part 1
Applying Math and Science in welding helps in understanding and solving welding problems.
Understanding why a MIG wire melts provides the reasons ...
NetWelding
uploaded
Welding Math Shielding Gas Flow Part 1
Math and Science are important for understanding and solving welding problems. They are also very useful tools if operating automatic welders and ...
NetWelding
uploaded
-
1 year ago
NetWelding
liked
Welding Math Shielding Gas Flow Part 2
Math and Science are important for understanding and solving welding problems. They are also very useful tools if operating automatic welders and ...
NetWelding
uploaded
-
1 year ago
NetWelding
liked
Pulsed MIG Reduces Fumes
Pulsed MIG welding can be used to reduce welding fumes by up to 80 to 90%. However the proper fast rise time Pulse MIG Power System must be used. ...
NetWelding
uploaded
-
1 year ago
NetWelding
liked
Body Engineering A Street Rod
To achieve the goal of 0 to 60 mph in less than 3.5 seconds selecting the proper body type is very important. Picking a 1934 Ford Sedan allows the...
NetWelding
uploaded
-
1 year ago
NetWelding
liked
MIG Gas Flow Control
The control of MIG welding shielding gas is more complex than meets the eye. Systems designed when the process was invented use high pressure to p...
NetWelding
uploaded
-
1 year ago
NetWelding
liked
Chassis-Engineering A Street Rod.mp4
The proper chassis is needed for a Pro Street/ Street Rod if you intend on achieving the performance a high horse power engine can deliver in a lig...
NetWelding
uploaded
In WWII, Oxyacetylene welding was the process of choice for welding 4130 CrMoly for aircraft. For the many small tubes welded, even today for ultra-light aircraft, Oxyacetylene welding may be the best choice. The slow cooling avoids any hard areas, which can occur with TIG! It takes practice a...